WWW9024M5WA Washing Machine User Manual 2
www.westinghouse.co.nz IMPORTANT INFORMATION THAT MAY IMPACT YOUR MANUFACTURER’S WARRANTY Adherence to the directions for use in this manual is extremely important for health and safety. Failure to strictly adhere to the requirements in this manual may result in personal injury, property damage and affect your ability to make a claim under the Westinghouse manufacturer’s warranty provided with your product. Products must be used, installed and operated in accordance with this manual.
5. DAILY USE - WASHING (Only) 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 Loading The Laundry................... 18 Using Detergent And Additives ... 18 Options Setting............................ 19 Starting A Cycle ( ) ................. 20 Interruption Of A Program ........... 20 Changing A Program................... 20 Changing The Options ................ 20 Opening The Door....................... 20 At The End Of The Program........
1. www.westinghouse.co.nz SAFETY INFORMATION 1.1 Conditions Of Use This appliance is intended to be used in household and similar applications such as: ˜ ˜ ˜ ˜ ˜ staff kitchen areas in shops, offices and other working environtment; farm houses; by clients in hotels, motels, and other residential type environments; bed and breakfast type environtments; areas for communal use in blocks of flats or in launderettes.
1.2 Child Safety ˜ This Washer-Dryer is not intended for use by young children or infirm persons without supervision. ˜ Young children should be supervised to ensure that they do not play with the appliance. ˜ The packaging components (e.g. plastic film, polystyrene) can be dangerous to children - danger of suffocation! Keep them out of children’s reach. ˜ Keep all detergents in a safe place out of children’s reach. Make sure that children or pets do not climb into the drum.
www.westinghouse.co.nz ˜ 1.4 Installation ˜ This appliance is heavy. Care should be taken when moving it. ˜ When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre. ˜ ˜ For safety reasons do not use double adaptors, extension cords and multi-plug adapters. Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning.
˜ ˜ ˜ The users should always check that they have not left their gas lighters (disposable or otherwise) in their clothing. Never tumble dry items which have had contact with chemicals such as dry cleaning fluid. These are of volatile nature and could cause an explosion. Only tumble dry items which have been washed in water or require airring. Plastic detergent dispensers should not remain in the drum during the drying cycle, as the plastic used is not designed to withstand the heat.
www.westinghouse.co.nz 2. PRODUCT DESCRIPTION 2.
Detergent/Softener Dispenser (For more informations, see page 18, 28) Transit Bolt (when remove) Softener Main Wash Prewash Door (when open) (for more informations, see page 18) Drum Lifter Stainless Steel Washing Drum Transit bolts must be removed before using the appliance. 2.2 Accessories Plastic Caps To close the holes on the rear side of the cabinet after the removal of the transit bolts.
www.westinghouse.co.nz 3. CONTROL PANEL 3.
3.2 Program Chart Max. Program; Spin Temperature Speed range Max. Load (Dry Clothes) Type of load and soil level Wash Dry 1200 rpm 9 kg 5 kg White and coloured cotton. Eco Cotton; 1200 1) rpm Cold to 40°C 9 kg 5 kg White and colourfast cotton. Set this program to have a good washing results and decrease the energy consumption. The time of the washing program is extended. Mixed; Cold to 60°C 1200 rpm 4 kg 3 kg Synthetic or mixed fabric items. Anti Allergy; 60°C 1200 rpm 1.
www.westinghouse.co.nz Program; Temperature range Max. Spin Speed Max. Load (Dry Clothes) Type of load and soil level Wash Dry Full Wash 60; 30°C, 60°C 1200 rpm 9 kg 5 kg Daily wear coloured cotton clothes such as shirts, blouses, towels and undergarments. Ideal for normal level of soil. WashDry 60; 30°C, 40°C 1200 rpm 1 kg 1 kg Non-Stop washing and drying program for 3 - 5 shirts with lightly soil. – – – Favourite Recall you favourite program.
3.3 Program Options Compatibility Option Program No Spin 2) Rinse Dryness Hold Level Cotton Eco Cotton 2) Time Dry 1) Delay Prewash Plus Start Hygiene Extra Rinse 3) Mixed Anti Allergy Delicates Bedding Extra Dirty Drain & Spin Rinse & Spin Wool Fast 15 Daily 39 Full Wash 60 WashDry 60 Favourite 1) Hygienic Care option can be combined with temperature 40°C to 90°C only. 2) Do not select a spin speed LOWER than that proposed by the appliance to avoid a too long drying time so saving energy.
www.westinghouse.co.nz ● No Spin ( ) No spin option eliminates all the spin phases and increase the number of rinses. ● Rinse Hold ( ) By selecting this option the water of the last rinse is not emptied out and the drum turns regularly to prevent the laundry creases. The door is still locked to indicate that the water must be emptied out. The door stays locked with the water in the drum. To continue the cycle, you must press (Start/Pause).
Dry Time Option Guidelines: Type of fabric Cotton and linen (bathrobes, bath towels, etc.). Load (kg) Spin Speed (rpm) Suggested Times (Hrs) Max.1) 2.5 - 4.5 1200 1200 3-4 2-3 2 1200 1-2 Synthetic or mixed fabric items ( jumpers, blouses, underwear, household linen, etc.). 3 1200 2-3 1 1200 1 Wool and hand washable wool. 1 1200 2 1) Maximum capacity depended on the model of the Washer Dryer (see defined on the control panel).
www.westinghouse.co.nz Additional drying Should the laundry still be too wet at the end of the program, set another short drying cycle. ● The final part of a washer - dryer cycle occurs without heat (cool down cycle). This ensures the laundry will be left at a low temperature. ● WARNING! To prevent the formation of creases or shrinking of fabrics, avoid excessive drying. 3.5 Settings Save Favourite ( ) Program Program settings that are frequently used can be saved (e.g.
Error warning beeps such as critical faults are not disabled. ˜ To disable the buzzer sound, press “Temp” and “Spin” touchpads at the same time about 3 seconds, the icon “ ” will show on display along with buzzer sound. ˜ To return to default configuration press these 2 touchpads at the same time about 3 seconds, the icon “ ” will show on display along with buzzer sound. 3.6 Start/Pause ( ) and Add Clothes ( ) Touchpad This touchpad has 2 functions: 1.
www.westinghouse.co.nz 5. DAILY USE - WASHING (Only) 5.1 Loading The Laundry 1. Turn the water tap on. 5.2 Using Detergent And Additives Please read “Detergents Type and Quantity of Detergent”on page 25 before use. 2. Connect the main plug to the main socket. 3. Press the On/Off button to turn on the Washer-Dryer. Turn the knob to set a program. The Washer-Dryer will propose a temperature and automatically select the spin value provided for the program you have chosen. 1.
When you use the liquid detergent - Do not use gelatinous or thick liquid detergents. - Do not put more liquid than the maximum level. - Do not set the “Prewash” phase. - Do not set the “Delay Start”. 2. Measure out the detergent and the fabric softener; - Pull out the dispenser drawer until it stops. - Measure out the amount of detergent required, pour it into the main wash compartment . - Close the drawer gently. NOTE The softener amount used must not exceed the “MAX” mark in the drawer.
www.westinghouse.co.nz 5.4 Starting A Cycle ( ) To start a program, press the Start/Pause touchpad. The corresponding pilot light will stop flashing and a default program duration will be displayed on the screen. After approx. 15 minutes from the start of a program: - The appliance will automatically adjust the selected program duration according to the type and size of the load. - The display will show adjusted program duration.
NOTE NOTE At the end of the program, the time remaining can suddenly decrease from 7 minutes or less to 0 due to the overestimated total program time during the load sensing phase. In some cases (with perfectly balanced load) the program time can be shorter than the time estimated after the load sensing phase is completed. This is a normal behavior of the machine and not a cause for concern as it does not compromise its performance. 5.
www.westinghouse.co.nz 6. DAILY USE - DRYING (Only) 1. Press the On/Off button to turn on the machine. The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe. 2. Make sure the load size does not exceed the maximum drying capacity of the machine. 3. Turn the knob to set a wash program which can select drying option (refer to Program Chart on page 11), according to your clothes then press Mode touchpad to switch your machine to Dry Only Mode. 4.
6. At the end of the program press the On/Off button to switch the machine off. At the end of each drying cycle, the temperature of your clothing will be high. For your safety, please leave the door open to let your clothes cool before removing your laundry. NOTE ● If you wish to open the door during the anti-crease phase or interrupt it, press Start/Pause touchpad. ● Some drying level options are not available for some programs.
www.westinghouse.co.nz 8. WASHING HINTS 8.1 Sorting The Laundry Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. 8.2 Temperatures Temp Soil level 90°C For normally soiled white cottons and linen (e.g. teacloths, towels, tablecloths, sheets...). 60°C For normally soiled, colourfast 50°C garments (e.g. shirts, night dresses, pajamas....
Oil based paint: moisten with benzine stain remover, lay the garment on a soft cloth and dab the stain; treat several times. Dried grease stains: moisten with turpentine, lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth. Rust: oxalic acid dissolved in hot water or a rust removing product used in cold water. Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole.
www.westinghouse.co.nz Not enough detergent causes: the washload to turn grey, greasy clothes. Too much detergent causes: oversudsing, reduced washing effect, inadequate rinsing. Use less detergent if: you are washing a small load, the laundry is lightly soiled, large amounts of foam during washing. 9. DRYING HINTS 9.1 Preparing The Drying Cycle As a dryer, the appliance works on condensation principle.
9.5 Additional Drying If the laundry is still damp at the end of the drying program, select a short drying cycle again. WARNING! Do not over dry the laundry in order to avoid creasing of fabrics or garments shrinking. 10. INTERNATIONAL WASH CODE SYMBOLS These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry. Energetic wash Max. wash Max. wash Max. wash Max.
www.westinghouse.co.nz 11. CARE AND CLEANING WARNING! You must DISCONNECT the appliance from the electricity supply, before you can carry out any cleaning or maintenance work. 11.1 External Cleaning Clean the appliance only with soap and warm water. Fully dry all the surfaces. CAUTION! Do not use alcohol, solvents or chemical products. To run a maintenance wash: The drum should be empty of laundry. Select the “Contton 90ºC” program. Press Start/Pause to start the program. 11.
Flush it out under a tap to remove any traces of accumulated powder. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance is operating. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump. To clean the drain pump: 1. Open the drain pump door. 11.
www.westinghouse.co.nz 3. When the container is full of water, put the drainage duct back again and empty the container. Do step 2, 3 again and again until no more water flows out from the drain pump. 5. Remove fluff and objects from the pump (if there are any). 6. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 4. Push back the drainage duct and turn the filter counter-clockwise to remove it. 7. Clean the filter under the water tap.
8. Put the filter back into the housing with exposed section facing up. Make sure that you correctly tighten the filter to prevent leakages. 3. Clean the filter in the inlet hose with a stiff brush. 4. Remove the inlet hose behind the appliance. 5. Clean the filter in the valve with a stiff brush or a towel. 6. Install the inlet hose again. Make sure that the couplings are tight to prevent leakages. 7. Open the water tap. Guide 9. Close the drain pump door. 11.
www.westinghouse.co.nz 11.9 Frost Precautions If the appliance is installed in an area where the temperature can be less than 0 °C, remove the remaining water from the inlet hose and the drain pump. Emergency Drain 1. Disconnect the main plug from the main socket. Turn off the water tap. 2. Remove the water inlet hose. 3. Remove the drain hose from the rear support and unhook it from sink or spigot. 4. Put the end of the drain and inlet hose in a container. Let the water flow out of the hoses. 5.
12. TROUBLESHOOTING 12.1 Possible Failures Alarm Code: Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please check troubleshooting. Once the problem has been eliminated, press the Start/Pause button to restart the program. If after all checks, the problem persists, contact your local Service Centre. WARNING! Deactivate the appliance before you do the checks.
www.westinghouse.co.nz Malfunction Machine does not empty and/or does not spin: There is water on the floor: Unsatisfactory washing results: The door will not open: Machine vibrates or is noisy: Possible cause Solution The drain hose is squashed or kinked. (Error code: ) Check the drain hose connection. The drain pump is clogged. (Error code: ) Clean the drain filter. The option “Rinse Hold” has been selected. Press Start/Pause touchpad to drain the water or select spin program.
Malfunction Machine vibrates or is noisy: Cycle time longer than displayed: The cycle is shorter than the time displayed. Spinning starts late or machine does not spin: Machine makes an unusual noise: No water is visible in the drum: Possible cause Solution The laundry is not evenly distributed in the drum. Pause the machine and redistribute laundry manually. There is very little laundry in the drum. Load more laundry. Unstable floors eg. wooden floors.
www.westinghouse.co.nz Malfunction Machine does not dry or does not dry properly: Display time is frozen at the end of drying cycle for more than 30 minutes: Possible cause Solution The “Time Dry” or the “Dryness Level” degree has not been selected. Select the drying time or the dryness level degree. The water tap is not turned on. (Error code: ) Open the water tap. The drain filter is clogged. (Error code: ) Clean the drain filter. The machine is overloaded.
12.2 Emergency Door Opening In case of power failure or appliance failure, the appliance door remains locked. The wash program continues when power is restored. If the door remains locked in case of failure, it is possible to open it using the emergency unlock feature. Before opening the door: WARNING! Make sure that the water temperature and the laundry are not hot. Wait until they cool down if necessary. Make sure that the water level inside the drum is not too high.
www.westinghouse.co.nz 13. TECHNICAL DATA Dimensions (Height / Width / Depth) 850 X 600 X 659 mm Power supply (Voltage / Frequency) 220 - 240 V~ / 50 Hz Wash: 2100 W / Dry: 1100 W Total power absorbed Minimum fuse protection 10 A Water supply pressure (Maximum / Minimum) Program Maximum dry clothes capacity Spin speed (Maximum / Minimum) Cotton Eco Cotton Mixed Anti Allergy Delicates Bedding Extra Dirty Drain & Spin Rinse & Spin Wool Fast 15 Daily 39 Full Wash 60 WashDry 60 Favourite 0.
2. Remove the cardboard top. 3. Remove the polystyrene packaging materials. 4. Remove the plastic bag which cover the machine. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene base. 5. Open the door. Remove all the items from the drum. 8. Pull up the appliance in vertical position. 9.
www.westinghouse.co.nz A 10. Remove the three transit bolts. 11. Pull out the plastic spacers. 3rd 14.2 Positioning 1st 2nd It is important that your machine stands firm and leveled on the floor to ensure correct operation. The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to avoid restricting the machine door. Use a spirit level on the top and side of the machine to check the levels. 12. Put the plastic caps in the holes (X3).
Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents vibration, noise and the movement of the appliance when in operation. clockwise “DOWN” 14.3 Water Inlet Connect the water inlet hose to a tap with 3/4” BSP thread. Use the hose supplied with the WasherDryer. DO NOT USE OLD HOSES. check counter clockwise “UP” When the Washer-Dryer is levelled, try to rock it from corner to corner.
www.westinghouse.co.nz In a sink, drain pipe branch. Fitting Hose Guide 1. Pull apart to insert hose. 450 approx. 42 Hose Guide bend hose pull hose 2. Adjust length to suit trough. This branch must be above the trap so that the bend is at least 60 cm above the ground. Max. 90 cm Min. 60 cm Push the drain hose onto the spigot and secure with a clamp, ensure a loop is formed in the drain hose to prevent waste from the sink entering the appliance.
14.5 Electrical Connection This machine is designed to operate on a 220 - 240 V, single-phase, 50 Hz supply. CAUTION! Connect the machine to an earthed socket outlet. “An incorrect power supply may void The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution. your warranty.
accessible. 44 www.westinghouse.co.nz 15. ENVIRONMENT CONCERNS 15.1 Packaging Materials The materials marked with the symbol are recyclable. >PE<=polyethylene >PS<=polystyrene >PP<=polypropylene This means that they can be recycled by disposing them properly in appropriate collection containers. 15.2 Old Machine Use authorized disposal sites for your old appliance.
NOTE
www.westinghouse.co.
G0034728-003-A20692015 www.westinghouse.co.
