Instruction manual

-18-
GROUNDING
This appliance must be grounded while in use to protect
the operator from electrical shock. The appliance
is equipped with a 3-conductor cord and a 3-prong
grounding type plug to t the proper grounding-type
receptacle. The appliance has a plug that looks like
Figure A. An adaptor, Figure B, should be used for
connecting Figure A plugs to two-prong receptacles.
The grounding tab which extends from the adaptor must
be connected to a permanent ground such as a properly
grounded outlet box as shown in Figure C using a metal
screw.
EXTENSION CORDS
Use only 3-wire extension cords which have 3-prong
grounding-type plugs and a 3-pole cord connector
that accepts the plug from the appliance. Use only
extension cords having an electrical rating not less than
the rating of the appliance. DO NOT use damaged
extension cords. Examine extension cord before using
and replace if damaged. DO NOT abuse extension
cord and do not yank on any cord to disconnect. Keep
cord away from heat and sharp edges.
Figure A
Figure B
Figure C
Circuit
Grounding
Conductor
Grounding
Prong
Metal
Grounding
Screw
Cover of
Grounded
Outlet Box
Grounding
Means
AA2220
GROUNDING INSTRUCTIONS
.
Remove all parts from packaging material and check to be sure there are no
missing parts.
.
Retain packaging material for storage of the Grinder and Grinder parts when not
in use.
UNPACKING INSTRUCTIONS
CIRCUIT BREAKER INSTRUCTIONS
-7-
PLEASE NOTE: This Grinder features an all hardened steel gear
transmission. This causes the Grinder to operate at a higher volume and
temperature than other Grinders. This is normal and will not affect the
Grinder’s performance.
This Grinder is equipped with a Circuit
Breaker as a safety precaution. If the Grinder
should stop running follow these steps to
remedy:
1. Turn the Grinder to the “Off” position.
2. Press the Circuit Breaker Reset Button
(Figure 16).
3. Turn the Grinder back on and resume
grinding.
4. If the Grinder still does not turn on, check that the electrical wall outlet is properly
working. Plug in another appliance to see if that appliance works from the wall outlet.
Check that the household circuit breaker has not been tripped. If none of the above
steps remedy the situation, or if the Circuit Breaker repeatedly shuts off the Grinder
contact a customer service for further assistance.
WARNING! DO NOT continue to use the Grinder if the Circuit Breaker trips
repeatedly. Continued use may cause permanent damage to the Grinder and will void
the warranty.
Circuit Breaker
Reset Button
.
DO NOT over-tighten the Front Ring Nut. It should be rmly tight.
.
Make sure the Grinding Knife blades lay at on the Grinder Plate.
.
DO NOT operate the Grinder without meat in the Head. Running the Grinder
while dry could damage the Head and Auger.
.
ALWAYS lubricate the Head, Grinding Plate and Grinding Knife with a food-
grade silicone spray after cleaning.
.
DO NOT grind bones, nuts or other hard objects.
.
If the Grinder Plate becomes clogged during operation, follow these steps to
restore normal output.
.
Turn the Grinder “OFF” and disconnect the Power Cord from the electrical outlet.
.
Remove the Front Ring Nut and Grinding Plate.
.
Thoroughly clean the Grinding Plate. Make sure all of the holes are clear.
.
Re-install the Grinding Plate and Front Ring Nut.
.
Re-connect the Grinder to the electrical outlet.
.
Continue with grinding.
.
Repeat as necessary.
GRINDING TIPS
FIGURE 16
If any components of this unit are broken or the unit does not operate
properly, call Pragotrade LLC Toll Free at
1-800-814-4895
Monday thru Friday 8:00am-5:00pm EST.
Outside the U.S. call 440-638-3131
O
I