Assembly Instructions

ManualsBrandsWFX Utility ManualsGarage & Tool StorageAshleigh 4 Shelf Shelving Unit Starter

Wire Shelving

SHOWN ASSEMBLED:

ASSEMBLY INSTRUCTIONS

Sort and count your parts!

LETTER

CODE

DESCRIPTION

QTY.

Determine the desired

position of the bottom shelf

(only); on each post, place

two C Half-Sleeves around

the post at the correct

position, with the LARGE

ends of the sleeves toward

the BOTTOM of the post and

the ridges inside the sleeves

fitting into the grooves in the

post. Press the two halves

until they snap together.

NOTE: the bottom shelf

must be mounted no more

than 12" from the floor.

LARGE

END

SMALL

END

RIDGE

GROOVE

LETTER

CODE

DESCRIPTION QTY.

STARTER

ADD-ON

UNIT

Set unit upright. Press shelf firmly at each shelf

corner, close to corner holes until firmly seated.

Stand a D Shelf on end, and from the BOTTOM side

of the shelf (the bottom side is recessed), slide the

TOP end of a post through a corner hole until the half-

sleeves are seated in the corner hole. Repeat with

remaining posts.

When ordering replacement parts,

please specify Black or Gray color.

To build the four corner

posts, screw the A Lower

Posts (with levelers) onto

the B Upper Posts (with

plastic caps). Hand

tighten.

STARTER UNIT

ADD-ON UNIT

PARTS LIST: STARTER UNIT

Lower Post (with leveler) 4

Upper Post (with plastic cap) 4

Half-Sleeve 32

Shelf 4

PARTS LIST: ADD-ON UNIT

Lower Post (with leveler) 2

Upper Post (with plastic cap) 2

Half-Sleeve 16

Shelf 4

S-Connecting Hook 8

UNIT

STARTER UNIT and

ADD-ON UNIT

Summary of content (4 pages)

PAGE 1
Wire Shelving PARTS LIST: STARTER UNIT A Q B Q C Q D Q DESCRIPTION QTY. Lower Post (with leveler) Upper Post (with plastic cap) Half-Sleeve Shelf D Q . 4 4 32 4 A Q B Q C Q D Q E Q DESCRIPTION STARTER UNIT QTY.
PAGE 2
5 Snap half-sleeve sets onto all four posts at desired height for next shelf. Lower next shelf into position and press until fully seated. Install third and fourth shelves in the same manner, with both shelves mounted ABOVE the post seams. 6 Connect optional add-on upper posts to lower posts using step 1. Install half-sleeves for bottom add-on shelf, refer to step 2. Insert posts into short side of addon shelf referring to steps 3 and 4.
PAGE 3
Étagères en treillis MODÈLE DE BASE MODÈLE COMPLÉMENTAIRE INSTRUCTIONS DE MONTAGE N’oubliez pas de trier et compter les pièces ! LISTE DES PIÈCES : MODÈLE DE BASE CODE ALPHABÉTIQUE A Q B Q C Q D Q DESCRIPTION QUANTITÉ Poteaux inférieur (avec les niveleurs) 4 4 32 4 Poteaux supérieur (avec casquettes en plastique) Fausse manche Tablette LISTE DES PIÈCES : MODÈLE COMPLÉMENTAIRE CODE ALPHABÉTIQUE A Q B Q C Q D Q E Q DESCRIPTION QUANTITÉ Poteaux inférieur (avec les niveleurs) 2 2 16 4 8 Poteaux
PAGE 4
Estantería de alambre LA UNIDAD BAS LA UNIDAD ADICIONAL INSTRUCCIONES DE ENSAMBLAJE Trier et compter les pièces ! Lista de piezas: Unidad base Clave alfabética A Q B Q C Q D Q DESCRIPCIÓN Poste inferior (con nivelador) Poste superior (con tapetas de plástico) Media manga Repisa CANTIDAD 4 4 32 4 SHOWN ASSEMBLED: STARTER UNIT and ADD-ON UNIT Lista de piezas: Unidad adicional Clave alfabética A Q B Q C Q D Q E Q DESCRIPCIÓN Poste inferior (con nivelador) Poste superior (con tapetas de plástico)