58Khz Common Platform EAS Systems Installation Manual April 2008 Manual Part Number: WG(Ver.
WARRANTY DISCLAIMER WG Security Products Inc. makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, WG Security Products Inc. reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of WG Security Products Inc. to notify any person of such revision or changes. WG SECURITY PRODUCTS INC.
TABLE OF CONTENTS OVERVIEW .................................................................................................................. 1 System Overview ........................................................................................................ 1 System Configurations................................................................................................. 2 Product Names and Part Numbers ...............................................................................
Common Platform EAS Systems OVERVIEW System Overview Note: Common Platform EAS Systems differ only in the antennas that are used. All systems use a universal transceiver printed circuit board that performs all the functions of transmitting, receiving and alarm notification. This manual applies to AdGuard, AdGuard XL, Lane Guard and Diamond Door Guard. The common platform line of products consist of one or more pedestals (transceiver antenna and optional extender), and one external PSU unit (WG SPS24).
Common Platform EAS Systems System Configurations Each transceiver pedestal is powered by its own dedicated SPS. The common platform SPS not only provides 24vac power to the transceiver pedestal, but it includes some very important features.
Common Platform EAS Systems Product Names and Part Numbers Accessories Accessory Name Order Number 1. Smart Power Supply (SPS unit) WG SPS24 2. Instruction Manual TBD 3. Power Line Connector (2 pins) TBD 4. Communication Connector (4 pins) TBD 5. Laptop Tuning Software (includes WG USB Cable) TBD 6. USB Tuning Cable TBD 7. WG IR Tuning Module TBD Antenna Name Order Number 1. AdGuard Transceiver Pedestal WG AGTR24 2. AdGuard Extender Pedestal WG AGTR-EX 3.
Common Platform EAS Systems Common Platform Features & Benefits • All-in-One platform design for the Acousto-Magnetic (AM) product line makes it a perfect AM detection core solution for various antenna forms and needs. There are visible advantages on short term and long term operation along with low cost maintenance.
Common Platform EAS Systems Specifications (common parameters) Smart Power Supply (SPS) Electrical 100vac ±10 % Primary Input (Stepdown Transformer) 110vac ±10 % 120vac ±10 % 220vac ±10 % 240vac ±10 % Secondary Output 26Vac ±5 % Rated Output Current 1.4A ±5 % Maximum Secondary Output Current 1.9 A Built-in Fuse (self recovery) 500mA Smart Power Supply (SPS) Mechanical Height 80mm ( 3.15” ) Width 110mm ( 4.33” ) Thickness 140mm ( 5.5” ) Weight 3 Kg ( 6.
Common Platform EAS Systems COMMON PLATFORM ELECTRONICS Board Functions Description Receiver Area External Sockets Antenna Sockets Transmitter Transformer 6
Common Platform EAS Systems PCB Sockets & Connections Board Power Input Fuse 2-Pin Power Connector Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin # Function I/O 1 GND Common GND 2 24VAC 26vac±5% 3 TX OFF Output 4 Alarm Input 5 AntiJammer Input 6 Alarm Volume Output 4-Pin Control Connector Pedestal Local Alarm and LED Connector USB connection cable or IR Tuning Module 7
Common Platform EAS Systems PCB Jumpers There is only one set of Jumper that is subject to User’s configuration; all other jumpers please keep them as original as system is delivered.
Common Platform EAS Systems Pedestal Tuning Access Common Platform systems include advanced tuning features that offer the technician a choice of access. There is a connector on the Transceiver PCB for tuning access. The installer can connect to the pedestal using a laptop PC with a WG USB cable or attach an external IR tuning and display module. The same dedicated tuning connector on the transceiver board accepts both the WG USB cable and external IR tuning and display module.
Common Platform EAS Systems Antenna Channels on Transceiver Board TX-B To Loop Antenna TX-A To Figure 8 Antenna Receiver Connectors TX-A and TX-B sockets connect to the two types of coil antennas. They must not be transposed; strictly follow the illustration.
Common Platform EAS Systems Fuse Replacement Information (Transceiver PCB) The fuse holder is accessed through the pedestal side panel. 1. Equipment shall be electrically disconnected from the main circuit supply when replacing the fuse. 2. Remove the fuse holder with a screwdriver, rotating it in a counterclockwise direction. 3. Replace the fuse in accordance with the specification noted above. Fuse Replacement: 5mm x 20mm 3.15A (Normal Fuse) 2.
Common Platform EAS Systems SMART POWER SUPPLY (SPS) SPS Controls and Connections SPS Front View SPS Power On/Off Switch SPS Top View Input Voltage Select Switch A Main AC Power In TX Antenna On/Off Switch Pedestal Alarm Volume Adjust 24vac Power & Data Output SPS Rear View Input Voltage Select Switch B 12
Common Platform EAS Systems SPS Box Terminals Illustration SPS Main AC Input Terminal Layout Main AC Cable (3 wires) Pin Function Color 1 Neutral Blue 2 Ground Green w/Yellow Stripe 3 Live Red(Brown) N - GND - L Pin: 1 2 3 Main AC Input Terminal LED Status Pin: 1 2 3 4 5 6 7 8 9 LED On Off TX Off TX is Off TX is On System Alarm Alarm Enabled Alarm Disabled Jammer Detection Detection Enabled Detection Disabled Alarm Volume Dim Means Weaker Bright Means Louder 10 SPS Output T
Common Platform EAS Systems SPS Box Main AC Input and Voltage Setup The Smart Power Supply (SPS) box accepts 5 input voltages: 100vac 110vac and 120vac in North America and Japan, 220vac and 240vac in Europe and Australia. Caution: Set the two Voltage Switches (A and B) o n the SPS at the specified combination based on the local incoming voltage value (see picture below).
Common Platform EAS Systems Interconnection between Smart Power Supply and Pedestal The system transceiver board has two sockets (combined pins 1 to 6) that connect to SPS output terminal pins 1 to 6 (one-to-one pin connection). The reference diagram shows the pin mapping relation between transceiver board and PSU. Isolated Multiple Conductor Cable Pin 1 Pin 1 Un-Shielded Pin 6 Pin 6 Caution! One SPS can power only one transceiver pedestal.
Common Platform EAS Systems Power Cord Notices The SPS delivered does not include AC cable for installation except a short testing cable; we recommend that you use a CE approved power cord H05 VV-F or H05 VVH2-F2 (Refer to the Electrical code which governs your country for installation of an Anti-Theft Unit to the Main power Supply) with the cable specification and gauge provided below.
Common Platform EAS Systems SPS Box External Relay interface The external relay interface is located at Output side of the SPS. Suggested Relay Ratings 1A@ 24 VDC Last 4 pins on this end. Pin 1 Pin 2 Pin 3 Pin 4Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 SPS Output Terminal Layout (10 pins) Alarm Relay SPS to Pedestal Cable (6 wires) Pin # 1 2 3 4 5 6 Function GND 24VAC TX OFF Alarm AntiJammer Alarm Volume 7 Jammer Relay 8 1A Contact Rating Electrical Notes: 1.
