Instructions / Assembly

ManualsBrandsWG Wood Products ManualsBathNapa Valley 79.5 in H x 15.5 in. W x 3.5 in. D Unfinished Recessed Medicine Storage Cabinet

2018 - Product Assembly & Installation Instructions

For ALL IN THE WALL MODELS

(913) 829-6000 WGWOODPRODUCTS@COMCAST.NET

1. Determine if your model is a single cabinet or a two-piece cabinet.

Two-piece cabinets will be 44” and taller and will have screws already in the

bottom of one cabinet section which allows you to screw the cabinet back

together. Two-piece cabinets will have the trim around three sides only. If

you have a two-piece cabinet, screw the two sections back together before

installation. Paint or stain the cabinet and door if desired. See Image 1

2. Screw on the Back Panels being careful to go straight so that your

screws don’t come out on the inside of the cabinet. Depending on model

and finish this may already be done. See Image 2

3. Use a stud finder to locate the studs and mark them.

You’ll want your product to go between the studs whenever

possible to avoid having to cut through one.

If you do need to cut through a stud, a reciprocating saw will do the

job without damaging the wall on the opposite side.

4. Measure the back side of the cabinet and lay out the marks on the

wall at the height you desire.

Models Covered:

Tools Needed:

Newberry, Reeves, Franklin, Concord, Cove Niches,

Blair, Bishop, Lawrence, Curio cabinets, Johnstown,

Franklins Baldwin, Napa Valley, Plantation, Elkhart

Kensington, Belmont, Basehor, Bookcase, Addison,

Archer, Regan, Grand, Blackwell, Belleview, WC-4

Series

Drill or Cordless Screwdriver with Phillips bit,

3/16

”

drill bit, Hammer, Scissors, tape measure and

pencil, drywall saw, caulking gun (Optional),

construction adhesive

Summary of content (4 pages)

PAGE 1
2018 - Product Assembly & Installation Instructions For ALL IN THE WALL MODELS Models Covered: Newberry, Reeves, Franklin, Concord, Cove Niches, Blair, Bishop, Lawrence, Curio cabinets, Johnstown, Franklins Baldwin, Napa Valley, Plantation, Elkhart Kensington, Belmont, Basehor, Bookcase, Addison, Archer, Regan, Grand, Blackwell, Belleview, WC-4 Series Tools Needed: Drill or Cordless Screwdriver with Phillips bit, 3/16” drill bit, Hammer, Scissors, tape measure and pencil, drywall saw, caulking gun (Optiona
PAGE 2
018 - Product Assembly & Installation Instructions For ALL IN THE WALL MODELS 5. Once your opening has been marked out on the wall use a drill and drill a 3/8” hole in each corner of your marked opening. Insert a drywall saw into the first hole and cut to the next one. Continue in this manner until you have the entire opening cut out. 6.
PAGE 3
2018 - Product Assembly & Installation Instructions For ALL IN THE WALL MODELS 10. You can do this either before it is installed in the wall, or after. The hinges can be mounted on either side of the cabinet for a left or right door swing. Your cabinet may have either a knob or handle(s), depending on the model. 11. For knobs and handles, drill a 3/16” hole where you want your cabinet knob or handle located. If your cabinet has a handle, the spacing between the two holes should be 3” center to center.
PAGE 4
2018 - Product Assembly & Installation Instructions For ALL IN THE WALL MODELS Image 1 attaching cabinet together Image 3 Apply Construction Adhesive Around the Edge of the Cabinet. Image 2 Tack on Back Panel Image 4 Apply Construction Adhesive ©2012 WG WOOD PRODUCTS , 213 FIELD END ST. SARASOTA, FL 34240 (913) 829-6000 WGWOODPRODUCTS @ COMCAST .