Technical Manual
Table Of Contents
- 0. Safety Precautions
- 1. Introduction
- 2. Function of the Coin Selector
- 2.1. Introduction
- 2.2. Programming Connector
- 2.3. Programming of Coins
- 2.4. Coin Selector Output Signals
- 2.5. Coin Blocking
- 2.6. Currencies and Coins
- 2.7. Slave Channels
- 2.8. Coin Return
- 2.9. Safety Features
- 2.10. RFID Card Reader Functionality EMP 500 v7 /CLB
- 2.10.1. Install whcashless App
- 2.10.2. Creation of an Operator Account
- 2.10.3. Setting the Identity of a Coin Selector
- 2.10.4. Getting multiple Operator Keys
- 2.10.5. Setting the Price(s) of a Coin Selector
- 2.10.6. Setting the Price with a Price Setting Key
- 2.10.7. Personalize a CLB Pay Key
- 2.10.8. Loading CLB Pay Key with funds via PayPal
- 2.10.9. Use the CLB Pay Key
- 2.11. Bluetooth Functionality
- 3. The EMP 500 v7 /CLB with Interface 06 – 1 Price Totalizer
- 4.
- 4. Serial Interface
- 5. RS232 Interface
- 6. Coin Selector Label
- 7. Maintenance
- 8. EC Conformation Declaration
- 9. Compliance Statements FCC / ISED for EMP 500 v7 /CLB
- 10. Appendix
- 11. Applications
Technical Manual EMP 500 v7 /CLB WH Münzprüfer Dietmar Trenner GmbH, Germany
version 2.7
page 36/62 subject to technical modification EMP 500 v7 /CLB
Timed credit clear
The function “Timed credit clear” specifies that a credit lower than the
pre-set price will be erased automatically after a programmed time. The
time after which the remaining credit should be erased is set in the same
window as this function is activated by means of the respective checkbox
(see Figure 17).
Always delete credit
This feature expands the function “Timed credit clear” in the way that a
credit that is higher or equals the set price is also erased after the time
out. It is essential that the function “Timed credit clear” is enabled when
“Always clear credit” is activated.
3.7.2. Automatic Erasure
This function features that the coin selector will automatically send a pulse
via the price line and deduct the credit each time the build-up credit
equals or exceeds the set price. This mode requires no signal from the
machine.
The setting of the duration is effected in the menu “Configuration” –
“Stepper/Timer” on the tab “Price” in the field “Pulse”. Figure 15 shows a
setting of the pulse length of 100 milliseconds.
The price line will be automatically activated again if the coin selector is
set for “multiple vend” and the remaining credit is higher or equals the
set price. The reactivation of the price line can be delayed by a
programmable time between 1 milliseconds and 65 seconds. The setting
is accomplished in the menu “Configuration” – “Stepper/Timer” on the tab
“Price” in the field “Pause”. Figure 14 shows a setting of the delay time of
100 milliseconds.
3.8. Display
For the EMP 500 v7 /CLB with interface 06 the 4-digit LED display D 500
is suitable. The display is connected to the programming connector (see
chapter 2.2 Programming Connector) of the coin selector. It can show the
price, the remaining value or the accumulated credit.
The configuration of the display functions is accomplished in the menu
“Configuration” – “Stepper/Timer…” on the tab “Display” (see Fig 18).
3.8.1. Hide Leading Zeros
This feature is to be activated, if left-hand zeros shall not be displayed. If
this feature is activated, e.g. 1.00 is displayed, whereas when this feature
is not activated 01.00 is displayed.