Instructions

ManualsBrandsWhadda ManualsArduinoMotor shield

Power shield that can drive: relays, solenoids, DC and

stepper motors

ILLUSTRATED ASSEMBLY MANUAL HKA03IP’1

KA03

Motor & Power

shield Arduino

Features

• For use with Arduino Due™, Arduino Uno™, Arduino Mega™

• Based on L298P dual full bridge driver IC

• Outputs: up to 2 DC motors or 1 bipolar stepper motor

• Power supply: external power or power from Arduino board

Specications

• Power supply: 7..46VDC

• Max current: 2A

• Dimensions: 68 x 53mm / 2.67 x 2.08”

Summary of content (12 pages)

PAGE 1
KA03 ILLUSTRATED ASSEMBLY MANUAL HKA03IP’1 Motor & Power shield Arduino® Power shield that can drive: relays, solenoids, DC and stepper motors Features • For use with Arduino Due™, Arduino Uno™, Arduino Mega™ • Based on L298P dual full bridge driver IC • Outputs: up to 2 DC motors or 1 bipolar stepper motor • Power supply: external power or power from Arduino board Specifications • Power supply: 7..46VDC • Max current: 2A • Dimensions: 68 x 53mm / 2.67 x 2.
PAGE 2
Subscribing our newsletter?, visit www.vellemanprojects.
PAGE 3
Velleman N.V.
PAGE 4
assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: • A good quality soldering iron (25-40W) with a small tip. • Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will protect the tip, and enables you to make good connections.
PAGE 5
DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE.
PAGE 6
Construction I CONSTRUCTION 3 Shottky diode 1 Resistors R... D7: 1N5819 D8: 1N5819 R1: 4K7 R2: 10K R3: 4K7 R4: 4K7 R5: 10K R6: 4K7 R7: 1K R8: 1K R9: 100K R10: 10K (4 - 7 - 2 - B) (1 - 0 - 3 - B) (4 - 7 - 2 - B) (4 - 7 - 2 - B) (1 - 0 - 3 - B) (4 - 7 - 2 - B) (1 - 0 - 2 - B) (1 - 0 - 2 - B) (1 - 0 - 4 - B) (1 - 0 - 3 - B) D1: D2: D3: D4: D5: D6: . 3pin T1: BC547B T2: BC547B 5 Male header C1: 100nF (104) CUT c..
PAGE 7
Construction 6 Female header 9 Electrolytic capacitors 8 Terminal blocks SK5 : 2p SK6 : 2p SK12 : 2p (motor 1) (motor 2) (power supply) C...
PAGE 8
Connection diagram II CONNECTION DIAGRAM 1 MOTOR DIRECTION LD1 Motor 1 5 PIN SELECT LD2 Motor 2 1 A 2 2 MOTOR’S DC Motor 1 2 B 1 DC Motor 2 1 BIPOLAR STEPPER MOTOR DC MOTOR 4 SELECT POWER SOURCE Vin: Power from Arduino (max. 2A) PWR: Power from external supply (max. 50VDC/6A) 3 EXTERNAL POWER SUPPLY INPUT Max. 50VDC/6A DOWNLOAD SAMPLE CODE FROM KA03 PAGE ON WWW.VELLEMAN.
PAGE 9
Schematic diagram IC1 GND GND D1 1N5819 D3 1N5819 1 2 3 4 SK5 SCREW02 5 LD1 LED5RL R7 1K POWER D2 1N5819 D4 1N5819 DIRA ENA DIRA2 GND 6 7 8 9 GND SENSE A SENSE B NC NC OUT1 OUT4 OUT2 OUT3 INPUT4 VS INPUT1 ENABLE B ENABLE A INPUT2 GND INPUT3 VSS GND 20 19 GND POWER GND D5 1N5819 18 D7 1N5819 17 SK6 SCREW02 16 15 14 13 12 DIRB2 D6 1N5819 ENB D8 1N5819 LD2 LED5RL 5V GND 11 R9 POWER GND 0 1 2 3 4 5 6 7 SK1 SK3 1 2 3 4 5 6 7 8 1 2 3 4 5 6 1 2 3 4 5 6 7 8 - 2 4 6 1
PAGE 10
PCB - 10 -
PAGE 11
Leds and how to use them Leds feature a specific voltage drop, depending on type and colour. Check the datasheet for exact voltage drop and rated current ! Never connect leds in parallel How to Calculate the series resistor: Example: operate a red led (1.7V) on a 9Vdc source. Required led current for full brightness: 5mA (this can be found in the datasheet of the led) Supply voltage (V) - led voltage (V) required current (A) 9V - 1.7V 0.
PAGE 12
The new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu Modifications and typographical errors reserved - © Velleman nv. HKA03’IP (Rev.1) Velleman NV, Legen Heirweg 33 - 9890 Gavere.