EZ-m mini-mixer OWNER’S MANUAL 10x2
Table of Contents Page 1 Introduction / Features / Back Panel diagram 2 Important Safety & Warranty Information 3 Detailed Features of the EZ-m 10x2 – Mic/Line Input Channel 4 Mono Mic/Line Channel - Low Impedance (Low Z) MIC Input - LINE IN - GAIN Control - CLIP LED 5 - Mono Channel EQ Section - Mono Channel PAN and LEVEL 6 Stereo Channel Inputs - BALANCE & LEVEL 7 MASTER Section - POWER LED & Signal Metering 8 - 2TK IN - 2TK OUT - MAIN OUT ¼” L/R Outputs - PHONES 9 - POWER Switch On/Off - AC Power Cable C
Introduction Thank you for purchasing a Wharfedale Pro EZ-m mini-mixer. The Wharfedale Pro EZ-m Series mixers are designed for ease of use and quality audio performance. Please read this manual completely to ensure proper understanding of the features and operation of your mixer.
Important Safety & Warranty Information 1. Power Supply This EZ-m Series mini-mixer is supplied with an external power supply unit. Use only the power supply provided with your mixer. Use of any other power supply could cause damage to the mixer and other equipment. Connect the power supply to the mixer BEFORE connecting it to the power source outlet. Be sure to allow for free airflow around the mixer, as it may become warm during long periods of operation.
DETAILED FEATURES OF THE EZ-m 10x2 Mono Mic / Line Input Channel 3
Low Impedance (Low Z) MIC Input 1 1 The low noise, high headroom “Low Z” MIC input is for use with balanced, low impedance dynamic microphones. NOTE: Condenser microphones will not work on this mixer. 2 LINE IN This ¼” Tip, Ring, Sleeve (TRS) jack is designed to be connected with (-10 to +4dBu) balanced or unbalanced line level sources.
5 EQ Section 5 Channel 1 on the EZ-m 10x2 mixer features a two band Equalization (”EQ”) section. Each band is chosen from the prime frequencies for most musical applications, and allows up to 15 decibels of boost (increase) or cut (decrease) of the signal in the tone range for which it controls. The HIGH EQ control is centered at 12kHz and the LOW EQ control is centered at 80Hz.
Stereo Channel Inputs Each of the stereo channels on the EZ-m 10x2 (2/3 and 4/5) feature two line level inputs with ¼” Tip/Ring/Sleeve (TRS) jacks for both balanced and unbalanced left and right input signals. These inputs can accommodate both stereo and mono inputs. When using a mono source, connect the cable to the LEFT (MONO) input only. Stereo Channels 2 /3, 4/5 have two inputs with left and right ¼” Tip/Ring/Sleeve (TRS) input jacks.
Master Section The master section on the right side of the mixer controls the final gain stage of the mixed signals from the input channels. The MAIN MIX control allows for the adjustment of the overall output level of the EZ-m mixer. 10 POWER LED & Signal Metering 10 10 POWER LED This amber LED lights indicating power is on for the mixer. 11 11 Level Meters The signal level of the MAIN MIX output is displayed on the 4 segment LED bar-graph meters. Levels shown are -20, 0, 6 and CLIP.
12 2TK IN This section consists of two sets of three input jacks. The top rows of jacks are the “2TK IN” input, which includes a 1/8” stereo jack and left and right RCA jacks. These inputs allow for an external stereo signal into the mixer. This 12 signal is controlled by the 2TK IN volume control and the 2TK TO PHONES switch as well as the 2TK TO MAINS switch. When the 1/8” 2TK IN jack is used, it takes priority over the RCA 2TK IN jacks.
16 16 POWER Switch – On/Off This slide switch turns the unit on and off. Always power down the EZ-m when it is not in use. Be sure to turn off all system amplifiers or powered speakers before turning off the mixer. 17 AC Power Cable Connector The included power adaptor connects here. Use only the power adaptor supplied with the mixer.
SPECIFICATIONS EZ-m mini-mixer 10X2 Specifications Maximum Output Level (1%T.H.D. @ 1kHz) THD+N% Frequency Response Hum and Noise Maximum Input Levels Mono Input Channel Gain +22dBu over 130mw (headphone) @ 32 ohms <0.
BLOCK DIAGRAM 11
Wharfedale International LTD. IAG HOUSE Sovereign Court, Ermine Business Park, Huntingdon, Cambs, PE29 6XU, England www.wharfedalepro.com IAG Professional reserves the right to alter or improve specifications without notice.