Specifications

NX-8E-CF CONTROL
35
LOCATION 203 - PARTITION SELECT, ZONES 177-184 (8 segments of feature selection data)
Location 203 is used to select the partition(s) that zones 177-184 reside in. A zone may reside in any combination of the 8 partitions. If a
burglary zone resides in more than 1 partition, it will only be active when all partitions are armed. A zone that resides in more than
1 partition will be reported to its lowest partition. Segment 1 corresponds to zone 177 and Segment 8 corresponds to zone 184.
Segments 1 - 8:
1 = Partition #1 3 = Partition #3 5 = Partition #5 7 = Partition #7
2 = Partition #2 4 = Partition #4 6 = Partition #6 8 = Partition #8
L LOCATION 204 - ZONES 185-192 ZONE TYPE (8 segments, numerical data)
Location 204 contains the Zone Type for zones 185-192. Segment 1 is for zone 185; Segment 8 is for zone 192. Default Zone Types are
found in the table on page 19. To customize a Zone Type, see page 28.
LOCATION 205 - PARTITION SELECT, ZONES 185-192 (8 segments of feature selection data)
Location 205 is used to select the partition(s) that zones 185-192 reside in. A zone may reside in any combination of the 8 partitions. If a
burglary zone resides in more than 1 partition, it will only be active when all partitions are armed. A zone that resides in more than
1 partition will be reported to its lowest partition. Segment 1 corresponds to zone 185 and Segment 8 corresponds to zone 192.
Segments 1 - 8:
1 = Partition #1 3 = Partition #3 5 = Partition #5 7 = Partition #7
2 = Partition #2 4 = Partition #4 6 = Partition #6 8 = Partition #8
LOCATION 206 – AUTO DISARM DAY SELECTOR (8 segments of feature selection data)
Location 206 selects which days each partition will auto disarm. Segment 1 is for partition 1, and segment 8 is for partition 8. If a zone is
faulted when the panel tries to auto disarm, the zone will be bypassed.
Segments 1-8: 1 - Auto Disarming on Sunday.
2 - Auto Disarming on Monday.
3 - Auto Disarming on Tuesday.
4 - Auto Disarming on Wednesday.
5 - Auto Disarming on Thursday.
6 - Auto Disarming on Friday.
7 - Auto Disarming on Saturday.
8 - Reserved.
LOCATION 207 – SERIAL PORT SELECTOR (1 segment of feature selection data)
Location 206 enables the serial port operations. There is one segment
“0” = Disabled (Default) “1” = NX584 enabled “2” = Serial Printer Enabled.
LOCATION 208 – BAUD RATE TABLE (1 segment of numerical data)
The NX-584 can operate on a number of different baud rates. Consult the home automation application information to determine the
best baud rate for your application and program it in Location 208. The default is “2” – 9600 Baud or the serial printer baud rate.
0 = 2400 Baud (2.4K) 2 = 9600 Baud (9.6K) 4 = 38400 Baud (38.4K)
1 = 4800 Baud (4.8K) 3 = 19200 Baud (19.2K) 5-7 = Reserved
LOCATION 209 – PROGRAMMING THE NX-8E-CF HOME AUTOMATION PROTOCOL (1 segment of numerical data)
The NX-8E-CF home automation protocol can operate in one of two possible modes - binary or ASCII. Consult the home automation
application information to determine the proper mode for your application and program it in Location 209. The default is “Off” – Binary.
Option 1 LED 0ff = Binary LED On = ASCII
Options 2 - 8 Reserved
LOCATION 210 – ENABLING THE NX-8E-CF TRANSITION-BASED BROADCASTS (2 segments of feature selection data)
The NX-8E-CF can be programmed to automatically send information to the home automation system whenever there has been a
change in this information. This is referred to as ‘transition-based broadcasting’. Which information packets use ‘transition-based
broadcasting’ is dependent upon the application and the capabilities of the home automation system. Location 210 is used to enable and
disable the appropriate transition based broadcasts. Consult the home automation application information and enable the appropriate
transition based broadcasts in Location 210.
Segment 1:
DATA ENABLES TRANSITION DATA ENABLES TRANSITION
1 Reserved 6 Zones Snapshot Message
2 Interface Configuration at power-up / program mode 7 Partition Status Message
3-4 Reserved 8 Partitions Snapshot Message
5 Zone Status Message