User Manual

Page 2
CIGAR PLUG
& 6' CABLE
IN LINE BUTT
CONNECTOR
MAGNET &
MOUNTING
HARDWARE
18
01
1
2
3
4
5
6
7
8
9
1
0
11
12
DRILL OUT
MOUNTING
HOLES
DRILL WIRE
ACCESS HOLE
HERE
RED +
BLACK
-
11
5 6
7 8
9
10
12
4
2
3
1
17
16
14
15
01-06839212( )
ASS'Y / 128 FPM 12 VOLT TWIN SPIN RB6
01-06839214( )
ASS'Y / 128 FPM 24 VOLT TWIN SPIN RB6
11-381574-00
BASE HOUSING
39-0402023-04
2 POS SOCKET HOUSING
1
SCREW 8 X 3/8 PHEXWASSHD SS/15-081916-066
44
LENS AMBER/68-4161381-10
67-1021600120 WIRE 16 GA 12" BLK. 61117-1 SCKT/STRIP 3/16"/
67-1021622120 WIRE 16 GA 12" RED 61117-1 SCKT./STRIP 3/16"/
11
19-261465-000 CLAMP RING
38-0141549-00 BASE DECAL
38-0241504-00 GASKET
01-2861506-00
MAGNET MOUNT KIT
01-2861522-00
MIRROR MOUNT KIT
15-101416-100 #10 X 5/8" PPHSMS
#10 X 3/4" PPHSMS15-101416-120
11
68-4161381-20 LENS BLUE/
68-4161381-30 LENS CLEAR/
68-4161381-40 LENS GREEN/
68-4161381-50 LENS RED/
68-4161381-V0
LENS VIOLET/
01-0461560-( )
LENS FILTER KIT
02-0363626-03
02-0363626-01
ASSEMBLY ROTATING REFLECTOR 128-24-35W/
ASSEMBLY / ROTATING REFLECTOR 128-12-60W
2
3
ITEM PART NUMBER DESCRIPTION
QTY QTY
11
12
13
14
15
16
17
18
19
20
21
4
5
6
7
8
9
10
1
1
1
1
1
1
1
1
1
A/R
A/R
1
A/R
3
A/R
A/R
A/R
A/R
A/R
A/RA/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
1
A/R
3
1
11
COLOR: R RED=
B=
G=
A=
C=
V=
BLUE
GREEN
AMBER
CLEAR
VIOLET
COLOR:
COLOR:
COLOR:
COLOR:
COLOR:
VOLTAGE: 2 = 12V 60W (128)
VOLTAGE: 4=24V 35W (128)
BASE: S STANDARD=
M=
R=
MAGNET
MIRROR
BASE:
BASE:
COLORBASIC PART NUMBER
01-2483921___
VOLTAGE
PART NUMBER KEY:
BASE TYPE
13
Mounting:
The RB6 Series uses a base that may be mounted one of two
ways. It is designed to be mounted in a normal dome- up
position. If mounted in an inverted position, seal the wire exit
hole and any mounting holes with silicone seal.
WARNING! All customer supplied wires that
connect to the positive terminal of the battery must
be sized to supply at least 125% of the maximum
operating current and FUSED
at the battery to carry
that load. DO NOT USE CIRCUIT BREAKERS WITH
THIS PRODUCT!
1” N.P.T. PIPE MOUNT:
1. Feed the beacon wires through the pipe.
2. Extend the RED beacon wire to +12VDC and fuse at 7.5
amps (see warning). Extend the BLACK beacon wire to
chassis ground (-). This unit is polarity sensitive!
3. Screw the strobe beacon onto the pipe, being careful not
to pinch or strain the wires. Hand tighten the unit onto
pipe.
Permanent Surface Mount:
Note: It will be necessary to remove the dome in
order to use this mounting style.
1. Remove the clamp ring securing the dome to the base
and remove the dome.
2. Locate the 3 mounting hole indentations on the inside
bottom of the base. Drill openings at these locations sized
to accommodate the sheet metal mounting screws
(customer supplied). Deburr these openings and remove
any shavings.
3. Using the base as a template, mark the location of the
three mounting holes and wire access hole onto the
mounting surface.
4. Using an appropriately sized drill bit (based on the
mounting hardware used and the thickness of the
mounting surface), drill the three mounting holes marked
in step 3. The wire access hole should be drilled using a
1/4” drill bit. Deburr all holes and install a rubber grommet
(customer supplied) to protect the wires.
5. Feed the wires through the wire access hole in the
mounting gasket, and the mounting surface.
6. Align the mounting holes in the base, gasket, and
mounting surface. Fasten with the three sheet metal
screws.
7. Extend the RED beacon wire to +12VDC and fuse at 7.5
amps (see warning). Extend the BLACK beacon wire to
chassis ground (-). This unit is polarity sensitive!
8. A magnet mount or mirror mount kit is available for
purchase separately (see parts list).