User Manual

Page 1
GND
SYNC
SCANLOCK
BLACK -
GREY -
WHT/VIO -
+12VSplit Lighthead: RED/WHT -
- +12VSolid Lighthead: LED COLOR
LIGHTHEAD
To Ground Terminal
To SYNC wire of other light
Flash Pattern Selection
To +12 Volts VDC
Fuse @ 3 AMPS / Customer supplied
NOTE: The positive wire will vary depending upon which lighthead you have.
6 - 32 X 5/16 PHX
WASHER HEAD
SCREW (2)
Fig. 1
Remove vent
cover
©2012 Whelen Engineering Company Inc.
Form No.14574 (032612)
Automotive: Lightheads
Installation Guide:
SideKick™ Super-LED® Fender Lights
2011 - 2012 Chevrolet Caprice
®
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: [phone]
Fax: [phone]
Internet: www.whelen.com
Sales e-mail: [e-mail]
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]
For warranty information regarding this product, visi85ww.whelen.com/warranty
Installation 2011 - 2012 Chevrolet Caprice:
1. Remove the vent panel following manufacturers instructions (Fig. 1).
2. Install the ION™ lighthead into the SideKick™ panel using the 2 supplied screws.
3. Extend the lighthead wires to your power source and snap the panel into the vent
panel opening.
Connecting the Lighthead to Power:
Route the lighthead wires along the same path as the vehicle’s main power cable and connect
to power.
WARNING: All customer supplied wires that connect to the positive terminal of
the battery must be sized
to supply at least
125% of the maximum
operating current and
FUSED at the
battery to carry
that load.
DO NOT USE
CIRCUIT
BREAKERS
WITH THIS
PRODUCT!
GND
SYNC
SCANLOCK
BLACK -
GREY -
WHT/VIO -
+12VSplit Lighthead: RED/WHT -
- +12VSolid Lighthead: LED COLOR
LIGHTHEAD
To Ground Terminal
To SYNC wire of other light
Flash Pattern Selection
To +12 Volts VDC
Fuse @ 3 AMPS / Customer supplied
NOTE: The positive wire will vary depending upon which lighthead you have.
6 - 32 X 5/16 PHX
WASHER HEAD
SCREW (2)
Fig. 1
Remove vent
cover
©2012 Whelen Engineering Company Inc.
Form No.14574 (032612)
Automotive: Lightheads
Installation Guide:
SideKick™ Super-LED® Fender Lights
2011 - 2012 Chevrolet Caprice
®
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: [phone]
Fax: [phone]
Internet: www.whelen.com
Sales e-mail: [e-mail]
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]
For warranty information regarding this product, visit www.whelen.com/warranty
Installation 2011 - 2012 Chevrolet Caprice:
1. Remove the vent panel following manufacturers instructions (Fig. 1).
2. Install the ION™ lighthead into the SideKick™ panel using the 2 supplied screws.
3. Extend the lighthead wires to your power source and snap the panel into the vent
panel opening.
Connecting the Lighthead to Power:
Route the lighthead wires along the same path as the vehicle’s main power cable and connect
to power.
WARNING: All customer supplied wires that connect to the positive terminal of
the battery must be sized
to supply at least
125% of the maximum
operating current and
FUSED at the
battery to carry
that load.
DO NOT USE
CIRCUIT
BREAKERS
WITH THIS
PRODUCT!