Instruction Manual

®
Paddle. Ski. Row +
THE WORLD'S ONLY PORTABLE MULTI-SPORT ERG MACHINE
Whipr Base Unit
Model: EQBSU-U00-BL1 or EQBSU-U00-BK1
Instruction Manual
Includes: Base Unit, Stabilizing Bracket (for door), Strap Anchor, Ground Anchor, Webbing
Strap, Carry Bag(Needs 3 AA Batteries - Not Included)
1)Install 3 AAA batteries. Batteries are located in the bottom of the unit. They can be installed by snapping off
the plastic cover by pulling on both sides.
2)Turn power on by pushing and holding button on the far left (the one with the circle and vertical line in it).
3)After turning power on, you will need to select the desired sport mode. To select the mode, you will press the
2nd button on the left (the one with the 3 horizontal lines). You will then press the button in the middle (the one
with the circle). The modes will be highlighted on the right. You will push the up or down button to select the
desired mode. The options are: ROW, KAYAK, SWIM, OPEN, SUP, SKI. After selecting the mode, press the
2nd button again (the one with the 3 horizontal lines).
4)Resistance Mode – should now be selected from the wheel located at the back of the unit (1-10…1 being the
easiest and 10 being the most difficult).
5)You are now ready to begin your exercise.
6)You can reset your workout any time by pressing the middle button (the one with the circle in it).
The Display Stats include the following:
Strokes/Minute, Distance, Time, 500 Meter Split Time, Projected Time, Calories, Average Watts
Securing the Unit – some modalities require the Base Unit to be secured. There are 3 ways to secure the unit.
Door - Securing the unit by using the attached inflatable anchor that goes under a door. The door should be a
standard 3.5cm width door with up to a 2cm gap.
1)Stabilizing Bracket needs to be attached to the base unit – this easily can be done by locking the tabs on the
bracket into 2 slots located on the bottom corners of Base Unit.
2)Slide the Bracket and Inflatable rubber anchor under the door.
3)Inflate the rubber anchor by pushing the larger of the 2 rubber balls on the Base Unit. You will need to keep
pushing it until the anchor and bracket are fully secure and very tight under the door.
When you are finished and would like to remove the Base Unit from the door crack, you can push the smaller
rubber ball and the anchor will deflate. After removing from under the door, the Bracket can be taken off easily
by pulling gently and removing from the grooves on the Base Unit.
Strap Anchor – The strap holder can rotate to be horizontal or vertical
1)Before attaching the strap anchor, make sure the plastic panel that the bladder folds into is securely attached
to the base unit. Also make sure the bladder is evenly placed in the square box (connects by magnets located
within the top of the bladder).
2)The lug bolts on the strap anchor easily locks into place on the back of the Base Unit.
3)Take the loop end of the strap and place through anchor hole.
4)Wrap around object.
5)Place buckle through loop and tighten..
Ground Anchor – To use ground anchor, put in ground and wrap strap around anchor.
See video links also: https://www.youtube.com/watch?v=7fCmaVLTanY
https://whipr.com/collections/whipr-ecosystem/products/whipr-base-unit
FCC DISCLAIMER
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canada IC DISCLAIMER
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
3. For WIFI product, it should be added:
This equipment complies with FCC’s and IC’s RF radiation exposure limits set forth for an uncontrolled
environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation
distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other
antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the
device (excluding its handset) and users.
Cet appareil est conforme aux limites d’exposition au rayonnement RF stipulées par la FCC et l’IC pour une
utilisation dans un environnement non contrôlé. Les antennes utilisées pour cet émetteur doivent être installées
et doivent fonctionner à au moins 20 cm de distance des utilisateurs et ne doivent pas être placées près d’autres
antennes ou émetteurs ou fonctionner avec ceux-ci. Les installateurs doivent s’assurer qu’une distance de 20 cm
sépare l’appareil (à l’exception du combiné) des utilisateurs.
RED DISCLAIMER
EU Declaration of Conformity
We,
WHIPR, INC.
251 Little Falls Drive, Wilmington, Delaware, 19808, USA
Declare that the DoC is issued under our sole responsibility and belongs to the following product(s):
Software Version: 11.03
Accessories: N/A
The object of the declaration described above is in conformity with the essential requirements of the
relevant Union harmonization legislation:
Radio Equipment Directive 2014/53/EU
The following harmonized standards and technical specifications have been applied:
Product Type: Whipr Base Unit
Model Number(s): EQBSU-U00-BL1, EQBSU-U00-BK1
Health and Safety (Article 3.1a):
EN 62479:2010
EN IEC 62311:2020
EMC (Article 3.1b):
ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301 489-17 V3.2.4 (2020-09)
EN 55014-1:2017+A11:2020
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019
EN 55014-2:2015
Radio Spectrum (Article 3.2):
ETSI EN 300 328 V2.2.2 (2019-07)
WIFI
(a) Transmitting frequency band(s):2412 MHz-2472 MHz
(b) Maximum allowed transmitting power in the frequency band(s) in which the radio equipment
Operates: E.I.R.P.: <20 dBm
Bluetooth
(a) Transmitting frequency band(s): 2402 MHz–2480MHz
(b) Maximum allowed transmitting power in the frequency band(s) in which the radio equipment
Operates: E.I.R.P.: <8 dBm
Notified Body Involved: N/A
Technical Compliance File Held by:
WHIPR, INC.
251 Little Falls Drive, Wilmington, Delaware, 19808, USA
Signed for and on behalf of WHIPR, INC.
Name and Title:
Adrina Lee, Director of Global Supply Chain
Address: 251 Little Falls Drive, Wilmington, Delaware, 19808, USA
Wilmington, Delaware 7/22/21
Place of issue Date of issue Signature of Authorized Person
UKCA Declaration of Conformity
We,
WHIPR, INC.
251 Little Falls Drive, Wilmington, Delaware, 19808, USA
Declare that the DoC is issued under our sole responsibility and belongs to the following product(s):
Software Version: 11.03
Accessories: N/A
The object of the declaration described above is in conformity with the essential requirements of the
relevant Union harmonization legislation:
Radio Equipment Directive Radio Equipment Regulations 2017
The following harmonized standards and technical specifications have been applied:
Product Type: Whipr Base Unit
Model Number(s): EQBSU-U00-BL1, EQBSU-U00-BK1
Health and Safety (CHAPTER
1 6(1)(a)):
EN 62479:2010
EN IEC 62311:2020
EMC (6(1)(b)):
ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301 489-17 V3.2.4 (2020-09)
EN 55014-1:2017+A11:2020
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019
EN 55014-2:2015
Radio Spectrum (6(2)):
ETSI EN 300 328 V2.2.2 (2019-07)
Notified Body Involved: N/A
Technical Compliance File Held by:
WHIPR, INC.
251 Little Falls Drive, Wilmington, Delaware, 19808, USA
Signed for and on behalf of WHIPR, INC.
Name and Title:
Adrina Lee, Director of Global Supply Chain
Address: 251 Little Falls Drive, Wilmington, Delaware, 19808, USA
Wilmington, Delaware 7/22/21
Place of issue Date of issue Signature of Authorized Person