Self Cleaning Hot & Cold Hidden Bottle Water Cooler Model No.: 8LIECH-SCSSFP5W USER MANUAL SAVE THIS MANUAL FOR FUTURE USE For service call: 1-844-494-4757 8LIECH-SCSSFP5W © 2014 Electrotemp Technologies Inc.
Model # 8LIECH-SCSSFP5W: Page 2 SAFETY PRECAUTIONS Your safety and the safety of others are very important. We have provided many important safety messages in this manual and your appliance. Always read and follow all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
Model # 8LIECH-SCSSFP5W: Page 3 SAFETY PRECAUTIONS ---Electrical Requirements WARNING Electrical shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. A 120 volt, 60 Hz., AC only, 15 amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended.
Model # 8LIECH-SCSSFP5W: Page 4 TABLE OF CONTENTS Safety Precautions ...................................................................... 2 Safety Precautions-Electrical Requirements ........................ 3 Product Features ........................................................................ 3 Key Information for Future Use ................................................ 4 Specifications ............................................................................... 5 Parts & Features .
Model # 8LIECH-SCSSFP5W: Page 5 SPECIFICATIONS Version 2.0 Energy Verified Power Supply 8Amp. Refrigerant Type R-134A Cold Water Power <100 Watts Cold Capacity / Hour 6 Litres / 1.59 Gallon Cold Temperature 3°C - 10°C / 37.4°F - 50°F Hot Water Power 870 Watts Hot Capacity / Hour 8 Litres / 2.11 Gallon Hot Temperature 80°C - 92°C / 176°F - 197.6°F Dimensions 1028 H x 320 W x 382 D (mm) 40.5 H x 12.6 W x 15 D (inch) Net Weight 36.2 Ibs / 16.
Model # 8LIECH-SCSSFP5W: Page 6 UNPACKING AND ASSEMBLY Remove the dispenser from packaging: WARNING TOP TO OPEN: TOP Excessive Weight Hazard TOP TOP Use two or more people to move and install the water cooler and the bottles. Failure to do so can result in back or other injury. 1. Lay dispenser on its side. 2. Open bottom flaps of the cardboard box. 3. Stand cooler up with flaps unfolded. 4. Pull box straight up. 5. Unpack the drip tray and insert it into the dispenser. 6.
Model # 8LIECH-SCSSFP5W: Page 7 CLEANING PRIOR TO INITIAL USE To remove any odors or dust that may have accumulated during shipment, you may want to clean the dispenser prior to first use. Time Required: 45 minutes. Notice: Do NOT plug in power cord yet. 1. Move the dispenser away from the wall and turn it 90° in either direction. 2. Turn the power switches to OFF. Stainless Steel tube for Self - Clean function 3. Remove the water bottle and the probe from the water bottle. A 4.
Model # 8LIECH-SCSSFP5W: Page 8 OPERATION IMPORTANT This unit is intended for water dispensing only. Do NOT use other liquids. Do NOT use for other purposes. Warranty is void if used with any other liquids such as coffee, tea, juices, beer or wine. This dispenser has been designed to use water bottles with a 3, 5, or 5.2 gallon capacity. Do NOT use alternative bottles. Initial Set Up Do NOT plug in until steps 1-2 are completed.
Model # 8LIECH-SCSSFP5W: Page 9 NOTE: When using a 5 gallon rectangular bottle, slide it into place as shown in the illustration below. • If the probe tube A and B(see previous page) are not sealed, the pump will run a few minutes and the night lights will flash. To correct, open the door, re-attach the probe, and close the door. • If the lights continue to flash, your bottle may be empty or there may be an issue with the water tube lines. Call 1-844-494-4757 for assistance. 3.
Model # 8LIECH-SCSSFP5W: Page 10 Dispensing Cold Water Note: After setup, it will take up to 6 hours to get the water to its maximum cold temperature. During this time, the compressor may run continuously as the refrigeration system builds the "Ice Bank" as noted in the "Product Features" section. 1. Position the bottle, glass, pitcher, or any container you are wishing to fill with water, securely below the cold water tap.
Model # 8LIECH-SCSSFP5W: Page 11 There may be a small amount of water left in the bottle. This is normal. 1. Open door and slide bottle out. 2. Remove the probe from the bottle: • Pull the probe straight up until completely out of bottle. 3. Install fresh bottle: WARNING Excessive Weight Hazard Use two or more people to move and install bottles. Failure to do so can result in back or other injury. • Place the fresh bottle in front of the tray.
Model # 8LIECH-SCSSFP5W: Page 12 2. The water pump delivers water to the cold tank. Besides a low humming pump noise, the sound of water running into the cold tank, can also be heard. 3. When the Hot Power Switch (see Parts and Features Section) is turned on, sounds of normal expansion and contraction of metal parts may be heard as the water is heated. 4. The refrigeration compressor works when water needs to be cooled. It has a very low pitch humming noise like that of your refrigerator. 5.
Model # 8LIECH-SCSSFP5W: Page 13 2. Fill the bottle with the water and bleach mixture. 3. Insert the probe into the bottle. 4. Slide the bottle into the cabinet and close the door. WARNING Electrical shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 5. Plug the power cord into a grounded wall outlet. 6. Turn the energy saving switches ON.
Model # 8LIECH-SCSSFP5W: Page 14 6. Turn the energy saving switches ON. 7. Allow the water to fill up the empty reservoirs. 8. Wait 10 minutes then turn the energy saving switches OFF and unplug the power cord. 9. Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser. 10. Remove the drain cap and the drain plug. Cold water will immediately flow into the bucket. After several seconds, hot water will dispense.
Model # 8LIECH-SCSSFP5W: Page 15 TROUBLESHOOTING Dispenser is not operating. • Make sure that the power cord is properly connected to a working outlet. • Confirm that power switches located in the back of unit are ON. They will glow in the ON position if they are on. • Turn them OFF and ON to make sure that cooler is plugged in and circuit breaker is not tripped. If needed, plug power cord into another receptacle to confirm there is electricity going to the water cooler. Water is leaking.
Model # 8LIECH-SCSSFP5W: Page 16 LED night lights are flashing and the dispenser is making beeping noises. • Replace the empty bottle. If unavailable, leave the door ajar or unplug the cooler to stop the beeping noise and the flashing lights. Dispenser is noisy. • Make sure that the dispenser is positioned on a level surface. Water tastes bad. • Drain the water from the reservoirs and replace the water bottle with a fresh one. • Clean dispenser as outlined in “ Proper Care & Cleaning ” section.
Model # 8LIECH-SCSSFP5W: Page 17 How to Connect /disconnect the quick connector and tubes 1. Remove U-shaped lock. 2. Press collet and pull tubing out. 3. If the end of the tubes have burrs, they can be removed by using a pencil sharpener as shown below. Do not create a large taper on the end of the tube because it can cause a leak. 4. Push tubing in until fully seated. 5. Reinstall U-shaped lock. IMPORTANT: Do NOT Return Dispenser To Store.
Model # 8LIECH-SCSSFP5W: Page 18 LIMITED WARRANTY Electrotemp Technologies Inc., (“Vendor”) warrants to the original purchaser of this dispenser, and to no other person, that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such dispenser shall be free from defects in material and workmanship.
/ ©2014 Whirlpool. All rights reserved. Manufactured under license by Electrotemp Technologies Inc., Mississauga, ON. Limited Warranty provided by manufacturer.
File Name:Manual 8LIECH-SCSSFP5W-English PN:5M009983XW00 Technical requirement: 1、Size: 215×279mm 2、Single color printing 3、Meets ROHS requirements 4、Sample must be confirmed before mass production. Do not revise drawing without authorization.