Refrigerator User Manual
Table Of Contents
- FRONT COVER
- A NOTE TO YOU
- SAFETY
- PARTS AND FEATURES
- INSTALLING YOUR REFRIGERATOR
- USING YOUR REFRIGERATOR
- SETTING THE CONTROLS
- CHANGING THE CONTROL SETTINGS
- ENSURING PROPER AIR CIRCULATION
- REMOVING THE SNAP-ON DOOR TRIM
- REMOVING THE DROP-IN DOOR TRIM
- ADJUSTING THE DOOR BINS
- ADJUSTING THE REFRIGERATOR SHELVES
- ADJUSTING THE UTILITY COMPARTMENT AND TRAY
- USING THE FLIP-UP DOOR SHELF
- REMOVING THE MEAT DRAWER AND COVER
- ADJUSTING THE EZ-TRAK REFRIGERATOR SHELF
- REMOVING THE CRISPER AND CRISPER COVER
- ADJUSTING THE CRISPER COVER TRACK
- ADJUSTING THE CRISPER HUMIDITY CONTROL
- ADJUSTING THE FREEZER SHELF
- REMOVING THE PULL-OUT FREEZER FLOOR
- USING THE OPTIONAL AUTOMATIC ICE MAKER
- REMOVING THE BASE GRILLE
- CHANGING THE LIGHT BULB
- REVERSING THE DOOR SWING
- SAVING ENERGY
- UNDERSTANDING THE SOUNDS YOU MAY HEAR
- CARING FOR YOUR REFRIGERATOR
- FOOD STORAGE GUIDE
- TROUBLESHOOTING
- REQUESTING ASSISTANCE OR SERVICE
- INDEX
- WARRANTY
28
3 & 4
2
1
ADJUSTING THE
FREEZER
SHELF
(on some models)
Adjust the freezer shelf to match the
way you use your freezer.
To remove the shelf:
1.Lift entire shelf slightly.
2.Move shelf all the way to one side.
3.Tilt other side up and out of shelf
support cups.
4.Pull shelf up and out.
To replace the shelf:
1.Tilt the shelf and insert into freezer
compartment.
2.Insert one end of the shelf all the
way into the center of the shelf
support cups.
3.Lower other end of shelf and insert
into the shelf support cups.
4.Lower shelf into place.
NOTE: The shelf should lower slightly
and lock into place. If the shelf does
not appear sturdy, make sure both
ends of the shelf are inserted
into the shelf support cups.
1 & 2
4
3
RÉGLAGE DE LA CLAYETTE
DU
CONGÉLATEUR
(sur certains modèles)
Régler la clayette du congélateur
pour correspondre à votre façon
d’utiliser le congélateur.
Pour retirer la clayette :
1.Soulever délicatement toute la
clayette.
2.Pousser la clayette complètement
vers un côté.
3.Soulever l’autre côté et dégager la
clayette de ses supports.
4.Retirer complètement la clayette.
Pour remettre la clayette :
1.Incliner la clayette et la glisser
dans le congélateur.
2.Insérer complètement une
extrémité de la clayette au centre
des supports de la clayette.
3.Abaisser l’autre extrémité de la
clayette et insérer dans les sup-
ports de la clayette.
4.Abaisser la clayette en place.
REMARQUE : La clayette doit être
légèrement abaissée et fixée en
place. Si la clayette ne semble pas
solide, s’assurer que les deux
extrémités de la clayette sont bien
insérées dans les supports.
LOW
HIGH
ADJUSTING THE
CRISPER
HUMIDITY
CONTROL
(on some models)
You can control the amount of
humidity in the moisture-sealed
crispers. Adjust the control to any
setting between LOW and HIGH.
•
LOW (open) lets moist air out of
the crisper for best storage of fruits
and vegetables with skins.
•
HIGH (closed) keeps moist air in
the crisper for best storage of
fresh, leafy vegetables.
RÉGLAGE DE
L
’
HUMIDITÉ DANS LES
BACS
À LÉGUMES
(sur certains modèles)
Ce réglage permet de contrôler le
degré d’humidité dans les bacs à
légumes étanches. La commande
peut être réglée à n’importe quel
réglage entre LOW (ouvert) et
HIGH (fermé).
•
En position LOW (ouvert), le réglage
laisse échapper l’air humide du bac
pour mieux conserver les fruits et
légumes à pelures.
•
En position HIGH (fermé), le
réglage permet de retenir
l’humidité à l’intérieur du bac pour
mieux conserver les légumes frais
et les légumes à feuilles.