Specifications

ground yonnector
7
Figure A
n If the ground connector is
located to the left on the back of
the termlnal box and looks like
Figure A, loosen the front nut on the
ground connector. Do Not loosen
the rear nut on the ground
connector.
Form the bare ground wire into a
U-shaped hook. Wrap ground wire
hook clockwise around ground
connector and between the rear
and front nuts. Securely tighten the
front nut over the ground wire.
Tighten strain relief or conduit
connector screws.
Figure B
If the ground connector is located
in the center on the back of the
terminal box and looks like Figure B,
loosen the front screw on the ground
connector. Form the bare ground
wire into a U-shaped hook. Wrap
ground wire hook clockwise around
ground connector and under the
washer. Securely tighten the screw.
Tighten strain relief or conduit
connector screws.
8
n Replace terminal box cover.
B
n Power supply cord
method (connecting
dishwasher to outlet).
Local codes may permit the use of
a U.L.-listed/GSA-certified, three-
conductor, power supply cord
terminated with a three-prong,
ground-type plug.
Some models are already equipped
with a power supply cord. If a power
supply cord is not supplied, Power
Supply Cord Kit (Part No. 43 17824)
is available at your local dealer
or parts supplier. Follow the
instructions packaged with the
power supply cord kit. If the kit is
not available locally, the power
supply cord used must be
a U.L.-listed/GSA-certified.
three-conductor, 16-gauge cord
that meets all local codes and
ordinances. The length of the
power supply cord must not
exceed six feet (1.8 m). It must be
routed so it does not touch the
dishwasher motor or the lower
portion of the dishwasher tub.
strain ryief
power co
A strain relief, available at your local
dealer or parts supplier, or a similar
part must be used to secure the
power supply cord to the
dishwasher terminal box.
Follow direct wire instructions for
disconnecting wires inside the
terminal box.
Recommended ground
method
Sprang, ground-type
wall receptacle
For your personal safety, this
dishwasher must be grounded. To
minimize possible shock hazard, the
power supply cord must be plugged
into a mating 3-prong ground-type
wall receptacle, grounded in
accordance with all national and
local codes and ordinances.
If a mating wall receptacle is not
available, it is the personal
responsibility and obligation of the
customer to have a properly
grounded 3-prong wall receptacle
installed by a qualified electrician.
The receptacle should be installed
on the rear or side wall of the
cabinet next to dishwasher
opening.
Water
readrements
Alltsoider connections must be
made before the water line is
connected to the dishwasher to
prevent damage to inlet valve.
Do Not solder within 6 inches (15 cm)
of the inlet valve. The plastic part of
the inlet valve could be damaged.
The hot water line to the dishwasher
must provide between 15 120 psi
(103-827 kPa) water pressure.
The hot water heater should be set
to deliver 120°F (49°C) water
temperature to the dishwasher for
best results.
Use 3/8” (9.5 mm) O.D. copper
tubing or l/2” plastic tubing
minimum inlet line. Dishwasher inlet
valve has 3/8” internal pipe thread.
Water line
connection
Electrical Shock Hazard
Disconnect electrical power at the
fuse box or circuit breaker box
before installing dishwasher.
Failure to do so can result in death
or electrical shock.
1 n Disconnect the electrical
power supply. Put on gloves and
safety glasses,
cabinet
wall
I
water supply
pipe
(15.26
I
(10.&m)
i
(253 cm)
/a
(5. :Smj
2 n Cut a l/2” (1.3 cm) minimum
hole in cabinet rear wall or floor for
water line.
3
n Rough in water line through the
l/2” (1.3 cm) minimum hole to
dishwasher cabinet opening.
Page 5