Specifications

ManualsBrandsWhirlpool ManualsHousehold Appliances50 Hz

368 201419

OVE

INSTALLATION INSTRUCTIONS

ACRYLIC WHIRLPOOL

K-1709T K-1709T-H

-1-

, 2006

Please read these instructions carefully to

familiarize yourself with the required tools, materials,

and installation sequences. Follow the sections that

pertain to your particular installation. This will help

you avoid costly mistakes. In addition to proper

installation, read all operating and safety instructions.

All information is based on the latest product

information available at the time of publication.

Kohler China Ltd. reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning,

and warranty information-please leave these

instructions for the consumer.

BEFORE YOU BEGINBEFORE YOU BEGIN

A. Ordering Information

ROUGHING-IN & DIMENSIONSROUGHING-IN & DIMENSIONS

17295T-CP

Hardware:

17295T-CP

Drain

Optional

HC103P

(GFCI)

B. Required Electrical Service

220~240V 5.1A 50Hz 750W.

220~240V 4.5A 50Hz 1000W.

Dedicated branch circuit required, protected with

Class A Ground-Fault Circuit-Interrupt (GFCI):

Pump

Heater HC103P

220~240 5.1 50

750

220~240 4.5 50

1000

1063633-T01-A

Summary of content (11 pages)

PAGE 1
OVE INSTALLATION INSTRUCTIONS ACRYLIC WHIRLPOOL K-1709T K-1709T-H BEFORE YOU BEGIN · Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to proper installation, read all operating and safety instructions. · All information is based on the latest product information available at the time of publication.
PAGE 2
C. Product Information C. K-1709T, K-1709T-H Fixture* Basin area Top area Weight Bathing well 1092 427mm 1585 625mm 42kg Water depth Capacity To overflow 327mm 214L * Approximate measurements for comparison only. Pump HP Voltage 1092 427 1585 625 327 214 42 * Frequency Amperage 1-Speed 1 HP 220~240 V Heater HP Voltage HC103P 1.36HP 220~240 V 50 Hz 5.1A Frequency Amperage 50~60 Hz 4.5A HC103P 1 220~240 50 5.1 1.36 220~240 50~60 4.5 D. D.
PAGE 3
PRODUCT NOTICES A. Installation Hazard Notification A. DANGER: Risk of fire, electric shock, or injury to Persons. Read important safety instructions on inside front cover of these instructions. WARNING: Risk of electrical shock. A licensed electrician should make all electrical connections. WARNING: Risk of electrical shock. Connect only to a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB). WARNING: Risk of electrical shock.
PAGE 4
C. Product Inspection C. Carefully unpack and inspect the whirlpool for damage. Leave all materials in the carton during constructions to prevent damage. NOTICE: Make sure both union connections to the pump are securely tightened. D. Electrical Connection D. 1. Pump The installation must have a 30mA Earth Leakage Circuit Breaker. The GFCI protects against Line-toGround shock hazard. Use a 220-240V, 10A (minimum), 50Hz dedicated service for the whirlpool. 2.
PAGE 5
INSTALLATION REQUIREMENTS A. Tools Required B. Materials Required · Adjustable pipe wrench · Rule · Level · Safety shoes · Safety glasses · Square · Screwdriver · Pliers · Utility knife A. · · · · · B. · · · · · · Plumbers putty Wall coverings, as necessary Silicone sealant Gypsum cement (optional) Construction adhesive (optional) · Protective covering for bathtub · Nails · · · · · · · · ( ( ( · · SITE REQUIREMENTS A. A. Old Bath Removal (If Applicable) Disconnect the drain at the trap.
PAGE 6
BEFORE INSTALLING WHIRLPOOL A. Your new whirlpool has been manufactured to the A. highest possible standards, it has been factory tested and approved. B. When removing bath from protective carton DO B. NOT LIFT BATH BY PIPE WORK. Inspect for any possible damage that may have occurred in transit. C. Identify motor access location before proceeding with installation. NOTE NO MOTOR ACCESS NO WARRANTY SERVICE. Ventilation must be provided in order to allow heat from motor to dissipate. C.
PAGE 7
E. E. Partially Install Whirlpool Bath Drain Install the drain on the whirlpool bath according to the drain manufacturer's instructions. When installing the drain overflow tube and hood, be sure to adequately seal along the edges of the hood to prevent leakage. Unpack drain (17295T-CP) and ensure that the Control Cable (9b) is not twisted or awkwardly bent. Please ensure that the bath is placed on woonden blocks or bricks to protect the waste body under the bath.
PAGE 8
7) Centralise Grating with Waste Body by lining up ribs of each directly in line and tighten Fixing Screw with a coin or suitable screwdiver. Do not overtighten - handtight plus 1/4 turn should be sufficient. 8) Adjust Plug by twisting Control Knob to the 'up' position and then fix Plug height by use of Adjusting Screw 2 . 9) Secure Flexible Pipe 13 by tightening Compression Nut against Compression Seal . 7) 10) Set drain pipe 16 , put on nut drain pipe 17 , and then tighten gasket 15 .
PAGE 9
COMPLETE FINISH WALL Drop-In Models: Bath Silicone Filler CAUTION: Risk of product damage. Do not support the weight of the bath by the rim. Finished tiled Wall Paste Mortar Brick or Concrete Wall For sunken type installation, construct the ceramic or marble tiles. Seal the joints between the bath rim and the tiled wall with silicone sealant. INSTALL PLUMBING CAUTION: Risk of damage to bath bottom and subfloor, Ensure a watertight seal on the bath drain connections. A.
PAGE 10
IMPORTANT: Your spa has been factory tested and approved. It is the responsability of the installer to test run the spa check all the fittings for leaks and test the control functions. NON OBSERVANCE WILL INVALIDATE FACTORY WARRANTY. DRILLING AND CUTTING ACRYLIC DRILLING: Small holes can be drilled with a twist drill, but the cutting edge MUST be backed off with an oil stone (the sharp edge dulled). Large holes must be drilled with a hole saw. Maximum drill size-12mm.
PAGE 11
LIMITED ONE-YEAR WARRANTY Plumbing Fixtures and Fittings Limited One-year Warranty Kohler plumbing fixtures and fittings are warranted to be free of manufacturing defects. This product is warranted for one year from date of purchase. Kohler China will be responsible for any problems caused by manufacturing defects provided with the invoice.