Troubleshooting guide

5019 301 05113
Whirlpool is a registered trademark of Whirlpool USA.
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. * To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
the water out.
Add the detergents as described in the programme table or in the chapter Detergents and Additives in the booklet. 1. Turn the
programme selector knob
to the
desired programme and temperature.
2. The pilot lamp of the
Start/Pause
button is
flashing.
3. The programme sequence and the predefined
spin speed indication corresponding to the selected programme lights up.
Selecting any option the indication lights up. When the combination of programme, additional options and temperature is not possible, the indication lights switch off automatically. Unsuitable combinations of options are deselected automatically.
Easy Ironing button  Can be used together with Cotton and Synthetics
programmes to make ironing easier.
 Increases the water quantity and the clothes are
spun very soft.
Eco Wash button  The duration of the wash is extended and the
temperature reduced to save up to 40% of energy but maintaining good washing results.
Prewash button  Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases approximately 15 min.
Intensive Rinse button  More water and a longer time in rinse cycle is added.  This option is particularly suitable for areas with
very soft water, washing baby linen and helps people with allergies.
Rinse Hold button  The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and prevent colours from changing.
 This option is particularly recommended for the
programme Synthetics or Delicates.
 This function is particularly useful if you want to
postpone spinning to a later time, or if you want to drain only.
Note:
The programme stops to Rinse Hold at the
time the Rinse Hold light in the programme flow indication is on.
CONSUMPTION DATA
Programme
Temperature
Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx.
Programme
Duration
(hours : minutes)
Cotton 95 5.0 49
*
1.70 1:50
Cotton 60 5.0 44 0.95 2:00 Cotton 40 5.0 44 0.55 1:50
Synthetics 60 2.5 55 0.80 1:25 Synthetics 40 2.5 50 0.60 0:50
Synthetics short 30 3.0 37 0.40 0:30
Delicates 30 1.5 50 0.50 0:45
Wool 40 1.0 55 0.50 0:40
Silk 30 1.0 37 0.40 0:40
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME SELECT ANY DESIDERED OPTION
Terminate the Rinse Hold option:  Press the Rinse Hold button again; the
programme will terminate automatically with the final spin cycle for the present wash programme.
 If you do not wish to spin the clothes, turn the
programme selector knob to the Drain programme and press the 
Start/Pause
 button
again when flashing.
Spin Speed Reduction button  Every programme has an automatic predefined
maximum spin speed.
 Press the button to set another spin speed.  If the spin speed 
0
 is selected, the final spinning
is cancelled but intermediate spin peaks remain during rinse. The water is drained out only.
Open the tap and press the
Start/Pause
button.
The pilot lamp of the 
Start/Pause
 button lights up.
The indicator lamps show the sequence reached in the programme. After starting the programme, the sequence indication runs from left to right through Wash, Rinse, Spin. When the sequence of the programme is finished the corresponding lamp goes out. The door can be opened when the Door Open indication is on.  All the lights of the programme sequence
indication are off.
1. Turn the programme selector to the

position.
2. Turn the water supply tap off. 3. Open the door and unload the machine. 4. Close the tap and leave the door ajar to allow
the drum to dry out.
1. Press the
Start/Pause
button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the
Start/Pause
button again. The
new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.
1. Press the
Start/Pause
button to pause the
programme. The light flashes.
2. Set the programme selector to Drain. The
spin indicators show
0
.
3. Press the
Start/Pause
button to start the
drain programme.
PROGRAMME START DOOR LOCK PROGRAMME END
CHANGE THE PROGRAMME, OPTIONS AFTER PROGRAMME START
CANCEL A PROGRAMME BEFORE THE END
3gb05113.fm5 Page 2 Wednesday, November 20, 2002 10:47 AM
Black Process Plate