Installation Instructions IMPORTANT: Read and save these instructions IMPORTANT: Installer: Leave Installation Instructions with the owner. Owner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use. www.whirlpool.com Part No.
Before you start... Your safety and the safety of others are very important. We have provided many important safety message in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will be preceded by the safety alert symbol and the word “DANGER” or “WARNING”. These words mean: Check location where washer will be installed.
Recessed area instructions Tools needed for installation: This washer may be installed in a recessed area or closet. The installation dimensions shown are the minimum spaces allowable. Additional spacing should be considered for ease of installation and servicing. If closet door is installed, the minimum air openings in top and bottom of door are required. Louvered doors with air openings in top and bottom are acceptable. Companion appliance spacing should be considered. level pliers 48 sq. in.
Now start... WARNING Excessive Weight Hazard Use two or more people to move and install washer. Failure to do so can result in back or other injury. Use new hoses and washers that came with your Whirlpool washer. Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found. When replacing your inlet hoses, mark the date of replacement on the label with a permanent marker. 5. coupling washer 2.
9. Stack two corner posts on top of each other. Tilt washer backwards and insert corner posts 3 inches (7.6 cm) in from one side of washer as shown. Repeat with other corner posts on other side of washer. 1/2" (1.3 cm) base 14. If washer is not level, adjust the front legs up or down. Make final check with level. When washer is level, use wrench to turn nuts on front legs up tightly against washer base. If nuts are not tight against washer base, the washer may vibrate.
Additional features WARNING Electrical Shock Hazard Disconnect power before making electrical connections. Failure to do so can result in death or electrical shock. For WARM RINSE: • Remove screws from each end of the console bottom. • Pull the console bottom forward; lift and tilt back. • Change BLUE wire on circuit board from COLD to WARM. To SAVE WATER: • Locate water level switch on back of washer. (See Back Page.) • Turn shaft 45° counterclockwise.
Typical full load sizes. Load Type Loading Suggestion Load Type Loading Suggestion Mixed Load 3 double sheets 4 pillowcases 6 pair shorts 8 T-shirts 2 shirts 2 blouses 8 handkerchiefs Heavy work clothes 3 pair pants 3 shirts 1 coverall 4 pair jeans 1 overall Permanent Press 2 double or 1 king size sheet 1 tablecloth 1 dress 1 blouse 2 slacks 3 shirts 2 pillowcases Knits 3 blouses 4 slacks 6 shirts 4 tops 4 dresses Operating Tips WARNING Moving the washer to a new location...
7" (18 cm) power supply cord Water level switch and shaft cold 1-1/2" (4 cm) hot water inlets 43" (109 cm) label 38-1/8" (97 cm) drain hose connector 35" (89 cm) 27-3/4" (70.5 cm) 7" (18 cm) 25-1/2" (65 cm) 5" (12.7 cm) 5-1/4" (13.3 cm) 27" (68.5 cm) 1" (2.5 cm) Part No. 8315965 ©2000 Whirlpool Corporation Prepared by Whirlpool Corporation Benton Harbor, Michigan 49022 Printed in U.S.A.
Instructions d’installation IMPORTANT : Lire et conserver ces instructions. IMPORTANT : Installateur : Remettre la brochure des instructions d’installation au propriétaire. Propriétaire : Conserver la brochure des instructions d’installation pour référence ultérieure. Conserver les instructions d’installation pour consultation par l’inspecteur local des installations électriques. www.whirlpool.
Avant de commencer. . . Votre sécurité et celle des autres est très importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité. Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous et à d’autres.
Instructions pour l’installation dans une cavité encastrée Outillage nécessaire pour l’installation : Il est possible d’installer cette laveuse dans niveau une cavité encastrée ou dans un placard. Les dimensions d’installation indiquées correspondent à l’espacement minimum admissible. Considérer de laisser des espaces plus grands pour faciliter l’installation et l’entretien. Si la porte du placard est installée, veiller à aménager des passages d’air de dimensions adéquates en haut et en bas.
Commencement. . . La laveuse étant dans la buanderie. AVERTISSEMENT Risque du poids excessif Utiliser deux ou plus de personnes pour déplacer et installer la laveuse. Le non-respect de cette instruction peut causer une blessure au dos ou d’autre blessure. Ruben adhésif d’expédition coupures, signes d’usure ou fuites apparaissent. Lors du remplacement des tuyaux d’alimentation d’eau, inscrire la date de remplacement sur l’étiquette avec un marqueur indélébile. 2.
1,3 cm (1/2 po) base écrou 10. Utiliser les pieds et les écrous fournis dans le sachet de pièces. Visser l’écrou jusqu’à environ 1,3 cm (1/2 po) de la base. 11. Insérer le pied dans le trou convenable à chaque angle avant de la laveuse, jusqu’à ce que l’écrou soit en contact avec la base de la laveuse. Ne pas serrer les écrous avant l’étape 14. 12. Incliner la laveuse vers l’arrière de la base et ôter les cornières. Abaisser doucement la laveuse sur le plancher.
Caractéristiques supplémentaires AVERTISSEMENT Risque de choc électrique Déconnecter le courant avant de faire des connexions électriques. Le non-respect de cette instruction peut causer un décès ou un choc électrique. Pour LE RINCAGE TIÈDE : • Enlever les vis de chaque bout de l’arrière du tableau de commande. • Tirer vers l’arrière du tableau de commande; soulever et incliner vers l’arrière. • Changer le fil BLEU sur le panneau de FROID (COLD) à TIÈDE (WARM).
Taille typique des charges complètes Type de charge Suggestion de chargement Type de charge Suggestion de chargement Charge mixte 3 draps (lit à 2 places) 4 taies d’oreiller 6 shorts 8 T-shirts 2 chemises 2 chemisiers 8 mouchoirs Vêtements de travail très sales 3 pantalons 3 chemises 1 combinaison 4 jeans 1 salopette Pressage permanent 2 draps (lit à Tricots 2 places) ou 1 drap (lit très grand) 1 nappe 1 robe 1 chemisier 2 pantalons 2 slacks 3 chemises 2 taies d’oreiller Conseils de fonctionnement
18 cm (7 po) Cordon d’alimentation Interrupteur et arbre de niveau d’eau froid 4 cm (1-1/2 po) chaud entrées d'eau 109 cm (43 po) étiquette 97 cm (38-1/8 po) Raccord du tuyau de vidange 89 cm (35 po) 70,5 cm (27-3/4 po) 18 cm (7 po) 65 cm (25-1/2 po) 12,7 cm (5 po) 13,3 cm (5-1/4 po) 68,5 cm (27 po) 2,5 cm (1 po) N° de pièce 8315965 ©2000 Whirlpool Corporation Préparé par Whirlpool Corporation Benton Harbor, Michigan 49022 Imprimé aux E.-U.