Hot & Cold Hidden Bottled Water Cooler Model No. : 8LIECH-BP-WL For spring water users, please follow the instructions shown in the "Descaling" section. USER MANUAL SAVE THIS MANUAL FOR FUTURE USE The appearance of your product may differ from the above illustration. For service, call: 1-855-594-4755 or E-mail Whirlpool@electrotemp.
Model # 8LIECH-BP-WL: Page 2 TABLE OF CONTENTS Safety Precautions........................................................................ Safety Precautions-Electrical Requirements ................................... Product Features ....................................................................... Specifications .............................................................................. Parts & Features .........................................................................
Model # 8LIECH-BP-WL: Page 3 SAFETY PRECAUTIONS Your safety and the safety of others are very important. We have provided many important safety messages in this manual and your appliance. Always read and follow all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or injure you and others.
Model # 8LIECH-BP-WL: Page 4 SAFETY PRECAUTIONS ---Electrical Requirements WARNING Electrical shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in serious injury, fire, or electrical shock. A 120 volt, 60 Hz., AC only, 15 amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended.
Model # 8LIECH-BP-WL: Page 5 SPECIFICATIONS Energy Verified Power Supply AC 120V / 60Hz / 5Amp Refrigerant Type R-134A Cold Water Power < 100Watts Cold Capacity / Hour 4 Liters / 1.06 Gallon Cold Temperature 3°C - 10°C / 37.4°F - 50°F Hot Water Power 425 Watts Hot Capacity / Hour 4 Litres / 1.06 Gallon Hot Temperature 80°C - 92°C / 176°F - 197.6°F Dimensions 102.8cm H x 32cm W × 38.2cm D 40.5inch H x12.6inch W × 15inch D Net Weight 15.8 Kg / 34.8 Ibs Version 2.
Model # 8LIECH-BP-WL: Page 6 UNPACKING AND ASSEMBLY Remove the dispenser from packaging: WARNING Excessive Weight Hazard Use two or more people to move and install the water cooler and the bottles. Failure to do so can result in back or other injury. 1. Lay the box containing the unit on its side. 2. Open bottom flaps of the cardboard box. 3. Stand cooler upright, with box flaps unfolded. 4. Pull box straight up. 5. Unpack the drip tray and insert it into the dispenser. 6.
Model # 8LIECH-BP-WL: Page 7 CLEAN OUT OF THE BOX, NO NEED FOR CLEANING PRIOR TO INITIAL USE Your water cooler is Clean Out of The Box. Cleaning described below is not required. However if you choose to clean your water cooler for any reason, please follow the instructions below. Time Required: 30 minutes. Notice: Unplug the power cord. 1. Remove the air filter and wash it in soapy water. 2. Submerge the probe head in the soapy water and rinse properly. 3.
Model # 8LIECH-BP-WL: Page 8 OPERATION IMPORTANT This unit is intended for use with high-quality bacteriologically safe bottled water only. Do NOT use other liquids. Do NOT use for other purposes. Warranty is void if unit is used with any other liquids, including tap water, coffee, tea, juices, beer, or wine. This dispenser has been designed to use with standard water bottles with a 3, 5, or 5.2 gallon capacity. Do NOT use alternative bottles. Initial Set Up Do NOT plug in until steps 1-3 are completed.
Model # 8LIECH-BP-WL: Page 9 NOTE: Fit all round bottles. When using a 5 gallon rectangular bottle, slide it into place as shown in the illustration below. • If the probe tube A and B are not sealed(see previous page), the pump will run a few minutes and the night lights will flash. To correct, open the door, re-attach the probe, and close the door. • If the lights continue to flash, your bottle may be empty or there may be an issue with the water tube lines. Call 1-855-594-4755 for assistance. 3.
Model # 8LIECH-BP-WL: Page 10 2. Press the right control downward to start dispensing water. 3. Release the control once desired fill level is achieved. Dispensing Hot Water Note: After setup, hot water will be available in 15-20 minutes. 1. Position the container you wish to fill with water securely below below the hot-water tap. • The left triangle below the hot water control indicates the location of the hot water tap (See the "Parts & Features" section on page 5).
Model # 8LIECH-BP-WL: Page 11 PROPER CARE & DESCALING General Cleaning Perform: As needed Time Required: 5 minutes. Note: Do NOT use abrasive materials or chemical cleaners. 1. Clean cabinet surfaces with a soft cloth and warm soapy water 2. Wipe dust from back of dispenser to improve efficiency. 3. Remove drip tray assembly by sliding it forward. Remove cover. Place tray and cover in dishwasher or wipe parts clean with a soft cloth and warm soapy water. 4. Reattach drip tray assembly.
Model # 8LIECH-BP-WL: Page 12 d.Re-attach the drain plug and plastic cap before proceeding. 4. Fill a bucket or empty 5-gallon water bottle with solution of white vinegar. For proportions, refer to "Descaling Solutions" section. Choose quantity in accordance with the frequency of your treatments. 5. Attach or insert the probe to the bucket/bottle. 6. Place the bucket/bottle into the cooler and close the door. The water will be pumped up into the holding tanks. 7. Wait for 1 hour. 8.
Model # 8LIECH-BP-WL: Page 13 TROUBLESHOOTING Call 1-855-594-4755 for service. Problem: Stainless steel surfaces are smudgy or fingerprinted. Solution: Use paper towel to wipe excess oils until surface feels dry to the touch. • To maintain beauty of stainless steel, oil it periodically using a stainless steel cleaning solution available at hardware stores, or use mineral oil (unscented baby oil). Problem: The buttons for dispensing water are slow-moving or jammed.
Model # 8LIECH-BP-WL: Page 14 Problem: Buttons are stuck. Solution: Apply mineral oil (unscented baby oil) to the button slides to reduce friction. Problem: No water is coming from the taps. Solution: Make sure the water bottle is not empty. If it is, replace it. If not, adjust the probe to an appropriate length. • Make sure that you fully press the water controls. • Make sure that the probe connection with the water bottle forms a complete seal. • Make sure that the door is closed.
Model # 8LIECH-BP-WL: Page 15 LIMITED WARRANTY Electrotemp Technologies Inc., (“Vendor”) warrants to the original purchaser of this dispenser, and to no other person, that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such dispenser shall be free from defects in material and workmanship.
®/™ ©2018 Whirlpool. All rights reserved. Manufactured under license by Electrotemp Technologies Inc., Mississauga, ON. Canada Limted warranty provided by manufacturer.