COLD AND ROOM TEMPERATURE BOTTLE WATER COOLER Model No.: 7LIECK-W-WL USER MANUAL SAVE THIS MANUAL FOR FUTURE USE For service call: 1-855-5-WHIRL-5 7LIECK-W-WL © 2014 Electrotemp Technologies Inc.
Model # 7LIECK-W-WL: Page 2 SAFETY PRECAUTIONS Your safety and the safety of others are very important. We have provided many important safety messages in this manual and your appliance. Always read and follow all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
Model # 7LIECK-W-WL: Page 3 SAFETY PRECAUTIONS ---Electrical Requirements WARNING Electrical shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. A 120 volt, 60 Hz., AC only, 15 amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended.
Model # 7LIECK-W-WL: Page 4 TABLE OF CONTENTS Safety Precautions ..................................................................... Safety Precautions-Electrical Requirements ............................. Product Features ...................................................................... 2 3 3 Key Information for Future Use .................................................. 4 Specifications ........................................................................... 5 Parts & Features ...........
Model # 7LIECK-W-WL: Page 5 SPECIFICATIONS Power Supply 1.5 Amp Refrigerant Type R-134A Cold Water Power 100 Watts Cold Capacity / Hour 5 L / 1.32 Gallon Cold Temp Range 3°C - 10°C / 37.4°F - 50°F Dimensions 91.3 H × 27.5 W × 28.6 D (cm) 35.9 H × 10.8 W × 11.3 D (inch) 25.4 Ibs / 11.5 Kg Net Weight PARTS & FEATURES Back Front Bottle Probe 1 Room Temp. Water Control 2 Cold Water Control 3 Room Temp.
Model # 7LIECK-W-WL: Page 6 UNPACKING AND ASSEMBLY Remove the dispenser from packaging: WARNING TOP TO OPEN: TOP TOP TOP Tip Over Hazard Do not use water cooler until base is attached to bottom of water cooler. Failure to do so can result in death or serious injury. 1. Lay dispenser on its side. 2. Open bottom flaps of the cardboard box. 3. Stand cooler up with flaps unfolded. 4. Pull box straight up. 5. Unpack the drip tray and insert it into the dispenser. (See illustration ) 6.
Model # 7LIECK-W-WL: Page 7 4. Install the Wall Mount Strap to prevent accidental tip over: • Unclip the strap from the back of dispenser. • Mount the strap 25 inches up from the floor directly to the wall stud with a screw (see Illustration A). If the stud is not available, insert and turn the anchor directly into the sheet rock using a star shaped screwdriver (DO NOT drill a hole into the sheet rock first when using this anchor).
Model # 7LIECK-W-WL: Page 8 CLEANING PRIOR TO INITIAL USE To remove any odors or dust that may have accumulated during shipment, you may want to clean the dispenser prior to first use. DO NOT PLUG THE COOLER INTO AN ELECTRICAL POWER OUTLET AT THIS TIME. Time Required for Set Up: 40 minutes. 1. Remove the bottle receptacle by turning it counterclockwise and pulling up. 2. Remove the plastic baffle from inside the reservoir. Clean with warm soapy water, rinse. 3.
Model # 7LIECK-W-WL: Page 9 INSTALLING THE CORRECT BOTTLE RECEPTACLE If your water bottle looks like this Then use this bottle receptacle This model comes with a Probe Receptacle (1). No changes are required. The Probe will push the Plug out of the way when you place the bottle into the receptacle. If your water bottle looks like this Then use this bottle receptacle 1. Remove the bottle receptacle (1) by turning it counterclockwise and pulling it up. 2.
Model # 7LIECK-W-WL: Page 10 OPERATION IMPORTANT This unit is intended for water dispensing only. Do NOT use other liquids. Do NOT use for other purposes. Warranty is void if used with any other liquids such as coffee, tea, juices, beer or wine. This dispenser has been designed to use water bottles with a 3 or 5 gallon capacity. Do NOT use alternative bottles. Initial Set Up Note: To avoid damage to the compressor, allow the unit to sit upright for at least 4 hours prior to operation. 1.
Model # 7LIECK-W-WL: Page 11 Dispensing Cold Water Note: After setup, it will take up to 6 hours to get the water to its maximum cold temperature. During this time, the compressor will run continuously. Compressor works to build up ice bank, this is normal. 1. Position the bottle, glass, pitcher, or cooking pot securely below the cold water tap. - The circular shapes in the drip plate help align the flow of water. This unit dispenses water at a fast rate.
Model # 7LIECK-W-WL: Page 12 PROPER CARE & CLEANING General Cleaning Perform: As needed Time Required: 5 minutes. Note: Do NOT use abrasive materials or chemical cleaners. They may scratch surfaces and contaminate drinking water. For cleaning hard spots suggest rubbing with toothpaste. 1. Clean the cabinet surfaces using a soft cloth and warm soapy water, then rinse. 2. Wipe dust at the back of dispenser to improve efficiency. 3. Remove the drip tray assembly by pulling it forward. Remove the cover.
Model # 7LIECK-W-WL: Page 13 6. Let it sit for 30 minutes. 7. Remove the cleaning mixture from reservoirs by dispensing it from both taps into a pitcher. 8. Wipe the inside of reservoir with a soft cloth.9. Fill the reservoir with 1 gallon tap water. 10. Remove the water from the reservoir by dispensing it from both taps into a pitcher. 11. Reattach bottle receptacle to this unit. WARNING Excessive Weight Hazard Use two or more people to move and install the water cooler and the bottles.
Model # 7LIECK-W-WL: Page 14 TROUBLESHOOTING Dispenser is not operating. • Make sure that the power cord is properly connected to a working outlet. Water is leaking. • Replace water bottle. Most common cause is a cracked bottle. • Call 1-855-5-WHIRL-5 for assistance. Push buttons are stuck and/or faucets are leaking. • Apply mineral oil (baby oil) to the button slides to reduce friction. No water is coming from the taps. • Make sure that the bottle is not empty. If so, replace it.
Model # 7LIECK-W-WL: Page 14 LIMITED WARRANTY Electrotemp Technologies Inc., (“Vendor”) warrants to the original purchaser of this dispenser, and to no other person, that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such dispenser shall be free from defects in material and workmanship.
® TM © 2013 Whirlpool. All rights reserved. Manufactured under license by Electrotemp Technologies Inc., Mississauga, ON. Warranty provided by manufacturer.
