THE RAZZA PLUS TM Portable Whirlpool Spa Owner's Manual R WHIRLPOOL BATH
IMPORTANT SAFETY INFORMATION READ AND FOLLOW ALL INSTRUCTIONS Jacuzzi Whirlpool Bath does not recommend spa water o temperatures in excess of 104 F. High water temperao tures in excess of 104 F. and prolonged periods of use can raise internal human body temperature excessively and impair the body’s ability to regulate its internal temperature. Limit your initial use of the spa to 10 - 15 minutes.
The Razza Plus™ Portable Whirlpool Spa Owner’s Manual Model 9400000 Contents Installation Instructions _________________________________________ Inspection and Shipping Claim ___________________________________________ Unpacking ___________________________________________________________ Positioning Your Spa ___________________________________________________ Electrical Requirements ________________________________________________ Electrical Precautions __________________________________________________ Out
The Razza Plus™Portable Whirlpool Spa Specifications and Installation Instructions The Razza Plus™ is an exquisite tear-drop shaped whirlpool spa by Jacuzzi Whirlpool Bath designed with fullfeatured elegance to provide the comfort and luxurious spa experience you expect from a Jacuzzi whirlpool spa. The Razza Plus features multi-level contoured seating for 5 or more people. Entry and exit from the spa are made easier and safer by the built-in exterior and interior steps.
INSTALLATION INSTALLATION INSTRUCTIONS Inspection and Shipping Claim Check for shipping damage upon receipt of the spa. Jacuzzi Whirlpool Bath is not responsible for damage to the spa sustained during shipping. If damage is evident before unpacking, see instructions regarding shipping claims on the outside of the carton and immediately file a claim with the carrier.
INSTALLATION Important: Read complete instructions before beginning installation. Positioning Your Spa Because your Razza Plus spa is portable, you can locate it just about anywhere you wish--on a deck,patio, or even indoors. Just be sure to position it above ground in an area with good drainage and on a level, continuous surface which can support the weight of the spa when filled with water and people; this weight is approximately 4017 lbs.
INSTALLATION Electrical Precautions CAUTION: Do not apply electrical power to the spa unless it is filled with water to the normal water level, which is approx. 9" below the spa rim (see location of water level indicator on face of skimmer on page 13). If the spa's motor/pumps are actuated when there is not sufficient water in the unit, the circulation pump could be irreparably damaged. Not heeding this caution will nullify the warranty.
INSTALLATION Equipment Set-Up 1. Remove the plastic sheet covering the spa. Use care; stepping into the spa with shoes will scratch the acrylic surface. • Select JETS on the SYSTEM switch. 2. Remove any packing materials from the spa. • Add 1/4 cup sodium dichlor (a fast dissolving granular type of chlorine) to the water and let the whirlpool run for 15-20 minutes only. 3. Remove each filter cartridge from its plastic bag. • Turn off JETS. 4.
OPERATION OPERATING INSTRUCTIONS Now that your Razza Plus spa is in place, you are probably eager to take advantage of its unique designed-in features—especially the patented Jacuzzi Whirlpool Bath hydromassage performance. Besides being a beautiful addition to your indoor decor or outdoor landscaping, your Jacuzzi® whirlpool spa will provide you with the ultimate in spa pleasure.
OPERATION Basic Control Set-Up (Continued) • Make sure the circuit protector buttons are pushed in. • Locate the HIGH TEMPERATURE SAFETY SWITCH which is a raised button on the end of the heater. Push this button to be sure it is in the reset mode. The purpose of this switch is to shut down the spa if the water becomes excessively hot. If, for some reason, the switch is tripped, the reset button must be pushed in for the heater to operate again after the water has cooled to about 100O F.
OPERATION air blower and light. Refer to the Control Panel illustration for an explanation of the various switch functions. SYSTEM continuous sequence indicated: The SYSTEM switch controls the following four functions in the continuous sequence indicated: 1. OFF 1. OFF 3. AIR/LIGHT 2. JETS 4. LIGHT 2. AIR 3. HTR/FLTR 4. FILTER (The next selection is OFF again.) Temp.
OPERATION Set the HEATER knob by rotating it to the desired temperature. When the water temperature is lower than that set by the HEATER knob, the heater and filter motor/ pump will be activated. The heater and filter functions will automatically turn off when the desired temperature is reached. When the heater is on, the water is also being filtered. The heater will also maintain water temperature in the JETS mode.
OPERATION Normal Operation Filtration Whirlpool System When you are ready to leave the spa, push the SYSTEM switch button to turn off the whirlpool. Then select the HTR/FLTR mode. Adjust the HEATER knob to the temperature at which you wish the water maintained. In this way, the water will be filtered when the heater goes on to maintain the temperature. Whenever the water temperature reaches the desired temperature, the pump will turn off.
MAINTENANCE MAINTENANCE Water Quality and Water Chemistry Maintaining water quality and water chemistry in your spa is extremely important and should be a regular part of your spa maintenance program, as a neglected spa can be a breeding place for dangerous bacteria. The water quality of your spa is maintained by a combination of filtration and chemistry.
MAINTENANCE Balancing pH: For good hygiene and equipment longevity, maintain the pH of your spa water according to the instructions provided. pH is the measure to determine if the spa water is too acid (low pH) or too alkaline or basic (high pH). The ideal range for spa water is 7.2 to 7.6 pH. For excessive acidity (below 7.2 pH) add soda ash or sodium bicarbonate to the spa water. For excessive alkalinity (above 7.6 pH) add dry acid to the spa water.
MAINTENANCE Water Level/Drain The water level in the spa must be maintained at its normal level. Evaporation and splashing will cause the water level to drop. spa is not occupied. In addition, its use will reduce energy consumption. When concentrations of impurities from evaporation, water quality chemicals, body oils, perfumes, dirty feet, and winds, etc., accumulate in the spa and cannot be filtered out, it is necessary to drain your spa and refill it with fresh water.
MAINTENANCE Automatic Filtration/Maintenance If you plan to be away, you should maintain minimum water quality by running the filter system. To do this, set the timer to turn the system on for at least two hours each day. This will cause the filter system to turn on at a desired time. Set the timer according to instructions on page 7 with the SYSTEM switch OFF. If you do not want the water to be heated, turn the HEATER knob to its minimum setting.
MAINTENANCE Spa Light Covering Your Spa Colored filters are provided with your spa. To change a filter, simply pull the filter out of the fitting and replace it with the desired colored filter. Replacement bulbs (#912) are also included. Put them in a safe place for future use. When a bulb burns out, replace it from the back of the light fitting, pulling out the bulb receptacle. An optional rigid spa cover is available to place on top of the spa.
TROUBLESHOOTING GUIDE PROBABLE CAUSE PROBLEM REMEDY 1. Control Switches do not respond. A. No power to the unit. B. Actuated too rapidly. 2. Heater not functioning. A. B. Heater mode not selected. High temperature safety switch tripped. A. B. C. C. D. Thermostat set lower than water temperature. No power to heater. E. F. G. H. Abnormally low water flow. Heater relay not operating. Heater element failure. Flow switch not operating. Check house circuit breaker and GFCI.C.
TROUBLESHOOTING GUIDE PROBLEM 6. Low water flow from jets. (Continued) 7. No water flow from jets. Suction or discharge line partially plugged. F. Pump running at subnormal speed. G. Worn or damaged pump seal. H. Subnormal voltage. E. * F. * A. B. C. A. B. C. E. D. E. Power turned off. Selector switch in OFF. House circuit breaker tripped; no power to system. Spa circuit protector tripped. High temperature safety switch tripped. F. GFCI tripped. G. Faulty pump or motor. H.
TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE 10. Motor will not start. (Continued) 11. Motor stops. 12. Air Blower does not operate. REMEDY I. Subnormal voltage. I. J. K. L. Locked shaft or impeller. Motor windings burned out. Defective starting switch inside motor. J. K. L. A. Motor overload condition. A. B. High temperature safety switch tripped. B. C. D. E. Selector switch failure. Relay failure. Inadequate supply wiring. C. D. E. A. B. C. Power off. ACCESSORY switch in OFF.
A LEVEL SPA SHELL WEIR BLADE Leveling the Cascade First make sure spa is in its final position and that it is level before proceeding. To ensure an equal flow of water over the cascade weir it may be necessary to level the weir blade. (See illustration A above.) Loosen the three screws that secure the weir blade to the spa shell; then proceed to level the weir blade by placing a small level on top of the weir blade. When the blade is level, tighten the screws.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.