Instruction for Use

ManualsBrandsWhirlpool ManualsDomestic Appliances9BRAKS9001A

5019 318 33435

D F NL

EXTRACTOR OR FILTERING HOOD INSTALLATION

The minimum distance between the support surface of the recipients on the cooking device and the lowest part of

the hood must not be less than 50 cm in case of electric cookers and 70 cm for gas or combination cookers. If the

installation instructions for the gas cooker specify a greater distance, this must be taken into account. Contact a

qualified technician for installation.

Do not connect the hood to the electrical power supply until installation is completed.

Warning! The exhaust pipe and clamps are not supplied and must be bought separately.

Very heavy product; hood handling and installation must be carried out by at least two persons.

Before beginning installation, decide which version of the hood you wish to use:

Extractor Version:

fumes are extracted and expelled to the outside through an exhaust duct fixed to the collar

(B)

at the top

of the hood.

Warning!

the hood is has a carbon filter fitted, the filter must be removed.

Filter Version:

air is filtered through two carbon filters and recycled into the surrounding environment.

Warning!

If the hood is not equipped with carbon filters, they must be ordered and fitted before use.

Mark a centre-line on the wall from the cooktop to the ceiling.

Bearing in mind the minimum heights over the cooktop specified above, mark the height of the hood on the wall with a

pencil

and place the template against the wall on the mark.

Using the template supplied, mark the holes, drill them and insert the rawlplugs, partly tighten 1 screw in the top rawlplug.

Fix the flue support to the wall as close as possible to the ceiling.

Hook the hood.

Adjust the position.

Fully tighten the top fixing screw.

Remove the grease filters and fix the hood from inside using 2

scr

ews and washers.

depending on hood version:

Extractor Version:

Fix an exhaust duct with the right diameter to the exhaust outlet of the hood and connect to an exhaust system ducted to the

outside (for fixture and connection of exhaust duct, utilize the most suitable system for the duct purchased).

Filter Version

Install the filter connection F on the collar B and secure with 1 screw.

• Connect the hood to the power supply!

Telescopic flue installation:

10.

Fix the telescopic flue tot he support with two screws.

11.

Slide the bottom section down into its seat on the top of the hood.

Summary of content (4 pages)

PAGE 1
EXTRACTOR OR FILTERING HOOD INSTALLATION The minimum distance between the support surface of the recipients on the cooking device and the lowest part of the hood must not be less than 50 cm in case of electric cookers and 70 cm for gas or combination cookers. If the installation instructions for the gas cooker specify a greater distance, this must be taken into account. Contact a qualified technician for installation. Do not connect the hood to the electrical power supply until installation is completed.
PAGE 2
4 2 x ø 8mm 2 x 5x45 1 ÷ 10 mm 5 3 3 x ø 8mm 1 x 5x45 B 2 B * 7 8 8 6 2 x ø 3x9 2 x ø 3x9 F * B 10 H *9 10 9 H 9 F * 11 H OK! * Only on some models 5019 318 33435 D GB F NL
PAGE 3
Replacing bulbs Disconnect the appliance from the power supply. Warning! Make sure lamps are cold before touching them. 1. Remove the clip that secures the lamp cover, then prise off using a small screwdriver or other suitable tool. 2. Replace the burnt-out bulb. Use a 40W max (E14) bulb only. 3. Refit the lamp cover and secure in place with the clip. Note: the lamp can also be accessed by removing the grease filters, but removing the lamp in this way is more difficult.
PAGE 4
SAFEGUARDING THE ENVIRONMENT Electrical connections 1. Packing The packing materials are 100% recyclable and are marked with the recycling symbol . Comply with local regulations for disposal. Packaging materials (plastic bags, polystyrene, etc.) can be dangerous for children and should be kept well out of their reach. 2. Product This appliance is marked in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).