NOTICE D’EMPLOI INSTRUCTIONS D’INSTALLATION AVANT D'UTILISER L’APPAREIL POUR LA PREMIÈRE FOIS MESURES DE PRÉCAUTION ET CONSEILS D’ORDRE GÉNÉRAL CONSEILS RELATIFS À L’ÉCONOMIE D’ÉNERGIE ACCESSOIRES DU FOUR NETTOYAGE ET MAINTENANCE DIAGNOSTIC RAPIDE SERVICE APRÈS-VENTE Pour tirer le meilleur profit de votre four, nous vous conseillons de lire attentivement la Notice d’emploi et de la conserver précieusement pour toute consultation future.
INSTRUCTIONS D’INSTALLATION Branchements électriques Avant de brancher l’appareil, assurez-vous que : 1. la tension nominale desservant votre habitation correspond à celle spécifiée sur la plaque signalétique de l’appareil ; 2. le système électrique est adapté à la puissance maximum absorbée par l’appareil, telle que spécifiée sur la plaque signalétique ; 3. le circuit d’alimentation électrique domestique est correctement raccordé à la terre.
65 cm min. 50 cm min. (selon modèle) Réglage 15 mm Fig. 1 max. Fig. 2 Installation Attention : Les parois des éléments contigus doivent résister à la chaleur (90°C minimum). Si l’appareil doit être installé à proximité de meubles de cuisine, respectez la distance minimum indiquée sur la figure ci-après. Un certain nombre de points doivent être observés lors du positionnement de la cuisinière.
AVANT D'UTILISER L’APPAREIL POUR LA PREMIÈRE FOIS • Retirez tous les accessoires du four et faites-le chauffer à 200 °C pendant environ deux heures, afin d’éliminer les odeurs dégagées par les graisses de protection et les matériaux isolants. Maintenez la fenêtre ouverte pendant toute la durée de cette opération.
MESURES DE PRÉCAUTION ET CONSEILS D’ORDRE GÉNÉRAL • L’appareil a été conçu uniquement pour la cuisson d'aliments à échelle domestique. Aucune autre utilisation n’est permise. Le fabricant décline toute responsabilité en cas d’éventuels dommages résultant d’une utilisation impropre ou d’un réglage incorrect des commandes. • Les réparations et opérations de maintenance doivent uniquement être effectuées par un technicien qualifié. • Évitez d’exposer le four aux agents atmosphériques.
CONSEILS RELATIFS À L’ÉCONOMIE D’ÉNERGIE • La table de cuisson est équipée de zones de cuisson et de plaques chauffantes de différents diamètres (selon modèle). Utilisez des cocottes et des casseroles avec un fond de diamètre égal ou légèrement supérieur à celui de la plaque chauffante/zone de cuisson. • Utilisez uniquement des cocottes et des casseroles à fond plat. • Les cocottes et les casseroles ne doivent pas dépasser au niveau du bandeau de commande.
NETTOYAGE ET MAINTENANCE Avant de procéder au nettoyage de l'appareil, débranchezle de l’alimentation électrique. • Nettoyez l'appareil avec un chiffon imbibé d’eau chaude savonneuse ou de détergent liquide dilué. • N’utilisez en aucun cas des produits abrasifs ou corrosifs, des produits chlorés ou des tampons métalliques. • N’utilisez en aucun cas des appareils d’entretien à la vapeur. • N’utilisez en aucun cas des produits inflammables.
Retrait des grilles latérales (selon modèle) Saisissez les grilles latérales par le bas et tirez-les vers le centre du four. Soulevez-les pour les extraire complètement. Tirez sur la grille latérale comme indiqué sur l’illustration (fig. 1). Après l’avoir libérée de ses attaches, soulevez-la. Inversez les opérations de la procédure ci-dessus pour remettre la grille latérale en place. Attention : Une fois le nettoyage terminé, veillez à reposer les grilles sur leur côté d’origine.
DIAGNOSTIC RAPIDE 1. L’appareil ne fonctionne pas : • Vérifiez l’alimentation électrique et assurezvous que l’appareil est branché au secteur. • Mettez l’appareil hors tension, puis remettez-le sous tension pour vérifier si le problème persiste. Attention : • Vérifiez que le sélecteur du four n’est ni sur “0”, ni sur le symbole «ampoule» . • Si le four ne s’allume pas, vérifiez que le programmateur de cuisson (selon modèle) n’est pas sur le mode manuel (voir les instructions figurant sur la Fiche produit).