Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADG 4500

NLFGBD

Before using the dishwasher, you are advised to read the user instructions!

On/Off button

Press the button to switch on the

dishwasher. The indicator light for the last

programme to be selected lights up; at the

end of the cycle the dishwasher emits a

brief audible signal.

Programme selection button

Press this button to select the desired

programme.

The indicator light of the selected

programme illuminates.

Indicator lights

Add regeneration salt

Only add regeneration salt immediately

before starting a wash programme.

Add rinse aid

Options

Half load

selector button

Press this button to select the half load

option; the corresponding indicator light

will illuminate. Press the button again to

the deselect the option; the corresponding

indicator light will go out.

The half load function is suitable for

smaller wash loads. The dishes should be

distributed over both racks.

“Delayed start” button

The wash cycle can be

programmed to start after 3-6-9

hours. The delayed start can be

programmed either before or after

selecting the desired wash

programme. When the door is

closed, a pre-wash cycle is run,

after which the delayed start

countdown begins.

Switch-on, programming, switch-off, etc.

procedures are only possible when the door is

open.

QUICK REFERENCE GUIDE

Summary of content (8 pages)

PAGE 1
GB QUICK REFERENCE GUIDE Before using the dishwasher, you are advised to read the user instructions! On/Off button Press the button to switch on the dishwasher. The indicator light for the last programme to be selected lights up; at the end of the cycle the dishwasher emits a brief audible signal. Options Half load selector button Press this button to select the half load option; the corresponding indicator light will illuminate.
PAGE 2
GB Fault indicators Indicator lights Off Blinking On The water stop device has been activated Switch off the appliance and contact After-Sales Service. The dishwasher has filled with too much water Reset and start the programme again from the beginning. If the problem persists, contact the After-Sales Service. Water heating system Reset and start the programme again from the beginning. If the problem persists, contact the After-Sales Service.
PAGE 3
GB Detergent 2) Programme Table Consumption 3) Loading tips A B Litres kWh Minutes Pre-wash cold Dishes to be washed later. _ _ 3.5 0.02 15 Delicate 45°C Lightly soiled items, with no dried-on food. X 9.5 1.10 65 Eco 1) 50°C Normally soiled items. X X 12 1.10 165 Normal 65°C Normally or heavily soiled dishes. X X 13.5 1.35 115 70°C Recommended programme for heavily soiled dishes, ideal for pots and pans. With additional antibacterial action. X X 15.5 1.
PAGE 4
GB HOW TO USE THE APPLIANCE Further indications are given in the individual chapters and in the user instructions. Open the door Press the On/Off button. C Large compartment A How to fill the detergent dispenser Small compartment B A B indicator C. Check the rinse aid level Mechanical Electric indicator on control panel (if provided).
PAGE 5
GB LOADING THE DISHWASHER RACKS Upper rack: Cup support racks (A): Depending on the position, raise or lower the racks. Place the glasses in the middle and to the right, dishes to the left, under the cup support racks. Place long and narrow utensils (carving forks, knives) on the bottom of the rack, not crosswise, with the sharp ends pointing inwards. depending on the model B A A B Rack release lever Rack height adjustment: Release the catches (B) of both rack rails. Take the rack out.
PAGE 6
GB Cutlery basket The basket has removable top grids into which items of cutlery can be inserted to keep them properly spaced and allow water to pass between them effectively. The cutlery supports and central lid are in the bag of accessories. The central lid is intended to act only as a cover: do not place the cutlery in it. The cutlery should be arranged in an orderly manner inside the basket, with the handles pointing downwards. Take care during loading to avoid injury from the knife blades.
PAGE 7
GB WHAT TO DO IF... If a fault occurs, before contacting our After-Sales Service, check the following troubleshooting guide to try and remedy the problem (*see also the corresponding chapter in the user instructions). Problem Cause Remedy The appliance is not working • No water supply. • Turn on the water tap. • The appliance doesn’t fill with enough water. • Clean the filter in the water supply tap. • Ensure the inlet water hose is not kinked. • There is a power failure.
PAGE 8
GB • can be removed • Streaks on the dishes/glasses. • Layer of salt on dishes/glasses. • Reduce the rinse aid setting *. • Close the salt container lid properly *. • not removable • Insufficient water softening, calcium deposits. • Change water hardness setting, if necessary add salt *. Opaque/cloudy glasses • Glasses are not dishwasher-proof. • Use suitable glasses. Rust on cutlery • Not made of stainless steel. • Use suitable cutlery.