Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADG 681 IX

-1-

Chart

START

DELAY

option

ON/OFF

BUTTON

PROGRAMME

SELECTOR

KNOB

(see “Table of

programmes”

below)

START BUTTON

The indicator lights up during operation, flashes when a fault occurs, and goes off

at the end of the programme.

START BUTTON RESET FUNCTION:

Press this button for at least 2 seconds; the selected programme and options will

be cancelled. Main failure displays (repeated flashing of the START indicator lamp)

can be cancelled by RESETTING. Detailed instructions are given in chapter

“What to do if...”.

(see at right for options description)

POWER

CLEAN

option

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional

options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of

the appliance’s automatic calibration system.

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on

the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

Table of programmes

Detergent

Consumption

Programmes

Available

options

Loading instructions Litres kWh

Minutes

Pre-Wash cold

Delay Crockery to be washed later. — 4.0 0.03 14

Quickwash 40°C

Delay

Lightly soiled crockery, with no

dried-on food.

* Use of tablets

not recommended.

10.0 0.65 30

Eco

50°C

Delay

Power

Clean

Normally soiled crockery.

Energy-saving programme.

X 12.0 1.05 165

Daily 60°C

Delay

Normally or heavily soiled

crockery.

X 13.0 1.25 120

Intensive 70°C

Delay

Power

Clean

Recommended programme for

heavily soiled crockery, especially

suitable for pots and pans.

X 14.0 1.55 155

DELAYED START

BUTTON

Press the button

(repeatedly) to delay the

start of the programme by

3, 6 or 9 hours.

Then press the START

button. The dishwasher

will start at the set time.

5019 396 01758ADG 681

SALT INDICATOR

When lit, the salt reservoir

needs to be refilled.

Options and display description

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE INSTALLATION

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

POWER CLEAN

Thanks to the additional

power jets this option

provides a more intensive

and powerful wash in the

lower rack, in the specific

area.This option is

recommended for washing

pots and casseroles

(see

page 4)

. Press this button

to activate Power Clean

(the indicator lights up).

RINSE AID INDICATOR

When lit, the rinse aid dispenser

needs to be refilled.

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE INSTALLATION INSTRUCTIONS! THE GUARANTEE IS NOT APPLICABLE IF FAULTS ARE CAUSED BY INCORRECT USE OF THE APPLIANCE. Options and display description PROGRAMME SELECTOR KNOB (see “Table of programmes” below) START BUTTON The indicator lights up during operation, flashes when a fault occurs, and goes off at the end of the programme.
PAGE 2
First time use How to set detergent type: powder/gel/tablet (if option is available) In order to always ensure the best cleaning results, you NEED to set: DETERGENT type and WATER HARDNESS. 1. Select 3rd programme 2. Press START button 3a. Check your (see Table of programmes for 7 seconds detergent type... - page 1) 3b....and set it on your dishwasher using the START button (as per table below) 4. Remember to use salt and rinse aid when needed (as indicated below) 5.
PAGE 3
Daily check Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) 1 The salt level indicator lamp may remain lit for the duration of several wash cycles. If the water hardness level falls within category (soft), no salt is required. Salt indicator (depending on the model) Visual indicator (depending on model). Screw on the cap. Salt residues around cap need to be removed. Add salt (never add detergent!). min. 1.5 kg max.
PAGE 4
How to load the racks How to load UPPER RACK 4 (In some models only) A - Multipurpose support: Different positions for long utensils, cups and glasses. B - Adjustable flaps: In horizontal position for cups/long utensils, in raised position for plates and stemware. How to adjust upper rack height (if available) - It could be useful to lift up upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select programme 6 Quick, permanent or alternating Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the panel (page 1). Choose programme according to the attached table of programmes (page 1). Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open.
PAGE 6
What to do if... If a fault occurs, before restoring normal appliance operation.contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... ...is not working/will not start ...shows “F1” on the display or the START indicator lamp flashes once ...shows “F4” on the display or the START indicator lamp flashes 4 times ...
PAGE 7
What to do if... Crockery and cutlery... ...salt indicator lit ...have deposits: regeneration salt residue ...are not dry Possible causes... Solutions... - Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up. - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly.
PAGE 8
Disconnect the mains plug What to do if... If, after carrying out the above checks, the fault persists, switch off the appliance, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).