Instruction for Use

ManualsBrandsWhirlpool ManualsDomestic AppliancesADG 690 WH

Whirlpool is a registered trademark of Whirlpool USA

5019 396 01130

ADG 690

Before using the dishwasher, read the

installation and maintenance instructions carefully!

1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to

different loads, extra functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness

and power supply voltage.

2) Energy label programme in compliance with EN 50242. - Information for Test Laboratories:

for more detailed information on

the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

1. OVERVIEW

Programme selector

START button

The indicator lights up during operation, flashes when a fault

occurs, and goes off at the end of the programme.

START button RESET function:

Press this button for at least 2 seconds; the selected programme

and options are cancelled. Main failure displays (repeated flashing

of the START indicator lamp) can be cancelled by RESETTING.

Detailed instructions are given in chapter 5 “What to do if...”.

Salt level indicator and rinse aid level indicator

These indicator lamps light up when salt or rinse aid need to be

added. Add just before starting a wash cycle.

Programme progress indicator

Fault indication and wash time display

With normal operation, the display indicates residual time (h:mm),

while with the “Delayed start” function selected it indicates time

remaining until the start of the programme (hh).

If “F..” appears on the display, see chapter 5 “What to do if...”.

Delayed Start button

Press the button (repeatedly) to delay the start of the programme.

Adjustable from 1 to 24 hours. With each press of the button, the

delayed start indicator increases by one hour and after 24 restarts

from 00. Then press the START button. The dishwasher will start

after the set time.

Detergent setting upon initial use and when using a different type of detergent

1. Select the third programme in the relative table.

2. Press the START button for approx. 7 sec. to change the display.

3. Using the START button, select the desired detergent:

Display shows: 2 -1 = 2 in 1, 3 -1 = 3 in 1, 4 -1 = other combined action

detergents (in this way, the rinse aid and/or salt indicator is deactivated).

Display shows OFF = Powder detergent (factory setting).

(rinse aid level and salt level indicator activated).

4. Switch the appliance off and then switch it on again. The selected detergent

type will be indicated on the display for approx. 3 seconds .

On / Off Button

Table 1.1.

Programme chart

Detergent

dispenser

Consumption

Programmes

Available

options

Loading instructions large small Litres kWh Minutes

SensorIntensive 60-70°C

Recommended programme for

heavily soiled crockery, with dried-

on food, e.g. pots and pans.

X X 13-20 1.10-2.00 100-150 ±

Quickwash 40°C

Lightly soiled crockery, with no

dried-on food.

X — 10.0 0.65 30 ±

Bio

50°C

Normally soiled crockery. Energy

Saving Programme.

X X 12.0 1.05 165 ±

Intensive 70°C

Recommended programme for

heavily soiled crockery, especially

suitable for pans and saucepans.

X X 14.0 1.55 155 ±

Power Clean 70°C

Recommended programme for

heavily soiled crockery, especially

suitable for pans and saucepans.

Intensive wash with additional water

jets.

X X 16.0 1.80 220 ±

Summary of content (8 pages)

PAGE 1
Before using the dishwasher, read the installation and maintenance instructions carefully! GB ADG 690 1. OVERVIEW Programme selector START button The indicator lights up during operation, flashes when a fault occurs, and goes off at the end of the programme. START button RESET function: Press this button for at least 2 seconds; the selected programme and options are cancelled. Main failure displays (repeated flashing of the START indicator lamp) can be cancelled by RESETTING.
PAGE 2
. QUICK REFERENCE GUIDE Detailed instructions are given on the following pages; also see section “5. What to do, in case of...” 1. Switch on the appliance Press the ON/OFF button. 2. Select a programme Press the button “Select programme” or the programme selector to display the selected programme. If required, select possible options. 3. Select the type of detergent The detergent selection procedure varies depending on the dishwasher model. Chapter “1.
PAGE 3
. HOW TO USE THE APPLIANCE PROGRAMME SELECTION Press the button “Select programme” or the programme selector to display the selected programme. The appliance must be switched on. If required, select possible options. The corresponding indicator lights up. The correct programme and the selectable functions are given in table 1.1 on page 1. Programme times stated in the table were obtained under normal conditions and may vary depending on conditions.
PAGE 4
3. HOW TO USE THE APPLIANCE c. How to adjust the rinse aid dosage regulator The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the lever 2 to open the cover. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again. If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3).
PAGE 5
3. HOW TO USE THE APPLIANCE HOW TO LOAD THE RACKS UPPER RACK - depending on model Multipurpose support A Three possible positions for long for utensils, cups and glasses. Dish holder B In horizontal position for cups/long utensils, in raised position for plates and stemware. Adjustable glass holder C Depending on the position, for small glasses or stemware. Long-handled utensils (kitchen knives) must be arranged with the sharp end facing in towards the appliance.
PAGE 6
4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
PAGE 7
5. WHAT TO DO IF... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes/solutions ...is not working/will not start - The appliance must be switched on. Check the household circuit fuse if there is no power supply. The dishwasher door must be closed.
PAGE 8
5. WHAT TO DO IF... Crockery and cutlery ... Possible causes/solutions ...are not perfectly clean/have food residues - ...have deposits: - regeneration salt residue - In the event of frequent use of the Eco programme 50°C (if available), from time to time select the intensive 70°C programme (if available). The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”).