Instruction for Use

ManualsBrandsWhirlpool ManualsOtherADG 7443 A+ FD

EN -1-

Chart

(see at right for options description)

PROGRAM SELECTION

BUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the program.

When the door is opened during a washing cycle, the

cycle is temporarily paused: the Start indicator blinks.

To resume the cycle push Start button and close

the door within 3 seconds.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may

vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic

calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/

Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

6th Sense

Power Clean

40-

70°C

Delay

Half-Load

Recommended program for routine

washes, with dried-on food

(e.g. EN 50242)..

X 7-14 1.00-1.65 80-165 Full

Pre-Wash cold

Delay Crockery to be washed later. — 4.0 0.03 14 NO

Rapid 45°C

Delay

Lightly soiled crockery, with no

dried-on food.

X 11.0 0.80 30 NO

Eco

50°C

Delay

Half Load

Normally soiled crockery.

Energy-saving program.

X 11.5 1.03 170 Full

Fast Daily 60°C

Delay

Half Load

Normally soiled crockery. X 10.0 1.30 80 Full

Steam

Delay

Program including steam action

dedicated for heavily soiled crockery,

pots and pans. Soaking or hand

pretreatment is no longer needed.

X 14.0 1.70 180 Full

RINSE AID INDICATOR

When lit (at the end of the cycle),

the rinse aid dispenser needs to be

refilled.

5019 300 02253

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING THE

CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF

NO CYCLE HAS STARTED.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

HALF LOAD BUTTON

Half load cycle can be used for the upper or lower rack.

Select the required program then press the “Half

Load” button - the light comes on. Turns off at the end

of the program.

The “Half Load” option can be used with the programs

indicated in the table of programs.:

DELAYED START BUTTON

Push the button (repeatedly) to delay

the start of the program - delay

indicator turns on. Adjustable from

1 to 24 hours. With each press of the

button, the delay increases by one

hour and after “h 24” returns to

“h 00”. When this option is selected

the delay indicator turns on.

Then press the START button.

The dishwasher will start after the

set time.

SALT INDICATOR

When lit (at the end of the cycle),

the salt reservoir needs to be

refilled.

TABLET SETTING

This setting allows to optimize

the cycle performances

according the type of

detergent used.

Push the Tablet button for

3 seconds (until the indicator

lights up) if you are using the

combined detergents in tablet

(rinse aid, salt and detergent in

1 dose).

If you are using powder

detergent or liquid detergent,

the Tablet indicator on the

control panel has to be off.

Quick reference guide

Whirlpool is a registered trademark of Whirlpool USA

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED. (see at right for options description) PROGRAM SELECTION BUTTON Push “P” button (repeatedly) until selected program number is shown on the display (P1...
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only before the first wash or if water hardness has been changed Water hardness level is factory set for medium-hard water (level 4). Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
PAGE 3
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B.
PAGE 4
How to load the racks UPPER RACK - depending on the model 4 A - Adjustable flaps (2 or 4): in horizontal position for cups / long utensils / stemmed glasses. A - CLOSED A - OPEN B - Cutlery basket: can be placed in the upper rack when the “Half load/Multizone” option is selected. The Grid (F) should be removed. TO OPEN A: CLICK! C D How to remove the upper rack (if available) It could be useful to remove the upper rack to load bulky items in the lower rack.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open. To pause the program (e.g.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes... salt indicator is lit rinse aid indicator is lit - Rinse aid dispenser is empty. - Refill dispenser with rinse aid (for more information - see page 3). ...
PAGE 7
What to do if... Crockery and cutlery... ...have deposits: regeneration salt residue Possible causes... Solutions... - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly. - Not enough rinse aid. - If you use a combined action detergent, try adding more rinse aid. - Plastic containers dry badly.
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.