Instruction for Use

ManualsBrandsWhirlpool ManualsDomestic AppliancesADG 7580

-1-

Chart

PROGRAMME SELECTION BUTTON

Press button “P” (repeatedly) until the indicator of the required programme lights

up (see “Table of programmes” below).

BUTTON

OFF

BUTTON

START BUTTON

The indicator lights up during operation, flashes when a fault occurs and goes off at

the end of the programme.

START BUTTON RESET FUNCTION

Press this button for at least 2 seconds; the selected programme and options are

cancelled. Main failure displays (repeated flashing of the START indicator lamp) can be

cancelled by RESETTING. Detailed instructions are given in chapter “What to do if...”.

(see at right for options description)

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions

(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible

with sensor programmes as a result of the appliance’s automatic calibration system.

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: fo

detailed information on the EN/Standard loading comparison test and other tests, contact the following address:

“nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697

standard of November 2001.

Table of programmes

Deter-

gent

Consumption

Programmes

Available

options

Loading instructions

Litres kWh

Minutes

Pre-Wash cold

Delay

Crockery to be washed later.

— 4.0 0.03 14

Quickwash 45°C

Delay

Lightly soiled crockery, with no

dried-on food.

* Use of tablets not

recommended.

11.0 0.80 30

Eco

50°C

Delay

Normally soiled crockery.

Energy-saving programme.

X 11.0 1.05 155

Antibacterial

Delay

Normally or heavily soiled crockery,

with additional antibacterial wash.

Programme interruption (e.g. due to

door opening) can compromise

elimination of germs.

X 13.0 1.50 115

Intensive 70°C

Delay

Recommended programme for

heavily soiled crockery, especially

suitable for pots and pans.

X 14.0 1.55 155

5019 396 01791ADG 7580

Options and display description

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE ASSEMBLY

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

DELAYED START BUTTON

Press the button (repeatedly) to delay the start of

the programme by 3, 6 or 9 hours. Then press the

START button. The dishwasher will start at the set

time.

RINSE AID INDICATOR

When lit, the rinse aid

dispenser needs to be refilled.

SALT INDICATOR

When lit, the salt reservoir

needs to be refilled.

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide ON BUTTON PROGRAMME SELECTION BUTTON Press button “P” (repeatedly) until the indicator of the required programme lights up (see “Table of programmes” below). BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! THE GUARANTEE IS NOT APPLICABLE IF FAULTS ARE CAUSED BY INCORRECT USE OF THE APPLIANCE.
PAGE 2
First time use How to set detergent type: powder/gel/tablet (if option is available) In order to always ensure the best cleaning results, you NEED to set: DETERGENT type and WATER HARDNESS. 1. Select 3rd programme 2. Press START button 3a. Check your (see Table of programmes for 7 seconds detergent type... - page 1) Detergent types 3b....and set it on your dishwasher using the START button (as per table below) 4. Remember to use salt and rinse aid when needed (as indicated below) 5.
PAGE 3
Daily check Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) Add salt (never add detergent!). min. 1.5 kg max. 2 kg Fill the salt reservoir with water before the first wash only. Visual indicator (depending on model). Unscrew cap. SEL SEL The salt level indicator lamp may remain lit for the duration of several wash cycles. If the water hardness level falls within category (soft), no salt is required.
PAGE 4
How to load the racks How to load UPPER RACK 4 B - Adjustable flaps: In horizontal position for cups/long utensils, in raised position for plates and stemware. (In some models only) A - Multipurpose support: Different positions for long utensils, cups and glasses. How to adjust upper rack height (if available) - It could be useful to lift up upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select programme 6 Quick, permanent or alternating Overview of programmes The max. possible number of programmes is illustrated in the chapter “Chart”. The corresponding programmes for your appliance can be found on the panel (page 1). Choose programme according to the attached table of programmes (page 1). Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... ...is not working/will not start ...shows “F1” on the display or the START indicator lamp flashes once ...shows “F4” on the display or the START indicator lamp flashes 4 times ...
PAGE 7
What to do if... Crockery and cutlery... ...salt indicator lit ...have deposits: regeneration salt residue ...are not dry Possible causes... Solutions... - Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up. - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly.
PAGE 8
Disconnect the mains plug What to do if... If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.