Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADG 8410 FD

EN -1-

Chart

(see at right for options description)

PROGRAM SELECTION

BUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the program.

When the door is opened during a washing cycle, the

cycle is temporarily paused: the Start indicator blinks.

To resume the cycle push Start button and close the

door within 3 seconds.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on

conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard

loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

* Power consumption in: Left-on mode: 0.70 W / Off-mode: 0.40 W.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

)

6th Sense

Power

Clean

40-70°C

Delay

Multizone

Power Clean

Use for normal soiled dishes with dried-on food. Senses the

level of soiling on the dishes and adjusts the program

accordingly. When the sensor is detecting the soil level an

animation appears in the display and the cycle duration is

updated. The Power Clean option is activated automatically

with this program. To deactivate, press the Power Clean

button on the control panel.

X 7-15 1.00-1.70 70-172 Full

P2 Pre-Wash cold

Delay

Multizone

Crockery to be washed later.

— 4.0 0.01 14-16 NO

P3 Fragile 40°C

Delay

Multizone

Light soiling, for example glasses and cups.

X 10.5 0.85 105-114 Light

P4 Rapid 45°C

Delay

Multizone

Lightly soiled crockery, with no dried-on food.

X 11.0 0.85 30-50 NO

Eco

50°C

Delay

Multizone

Power Clean

Normally soiled crockery.

Standard Program the most efficient in terms of its combined

energy and water consumption.

X 10.0 0.92 240 Full

P6 Fast Daily 60°C

Delay

Multizone

Normally soiled crockery.

X 11.0 1.30 80-95 Full

P7 Silent 50°C

Delay

Multizone

Normally soiled crockery, gentle and quiet thanks to the

lower spray pressure (39 dbA).

X 14.0 1.20 290-299 Light

P8 Intensive 65°C

Delay

Multizone

Power Clean

Recommended program for heavily soiled crockery,

especially suitable for pans and saucepans.

X 15.0 1.60 165-175 Full

P9 Hygiene

Delay

Multizone

Power Clean

Normally or heavily soiled crockery, with additional

antibacterial wash. Program interruption (e.g. due to door

opening) can compromise elimination of germs.

X 14.0 1.40 110-120 Full

P10 Dual Wash

Delay

Multizone

Power Clean

This program is able to manage different wash intensity for

each rack. You can optimize loading and properly wash

different crockery in one cycle, loading delicate items in

upper rack and pots and pans in lower rack.

X 15.0 1.50 155-170 Full

5019 300 00778

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ

THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING

ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING

THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER

30 SECONDS IF NO CYCLE HAS STARTED.

SALT INDICATOR

When lit (at the end of the cycle), the

salt reservoir needs to be refilled.

RINSE AID INDICATOR

When lit (at the end of the cycle), the

rinse aid dispenser needs to be refilled.

TABLET SETTING

This setting allows to

optimize the cycle

performances according

the type of detergent

used. Push the Tablet

button for 3 seconds (until

the indicator lights up)

if you are using the

combined detergents in

tablet (rinse aid, salt and

detergent in 1 dose).

If you are using powder

detergent or liquid

detergent, the Tablet

indicator on the control

panel has to be off.

DELAYED START

BUTTON

Push the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to 24

hours. With each press of

the button, the delayed

start indicator increases

by one hour and after

24 restarts from 0.

Then press the START

button. The dishwasher

will start after the set

time.

POWER CLEAN

Thanks to the additional power jets

this option provides a more intensive

and powerful wash in the lower rack,

in the specific area. This option is

recommended for washing pots and

casseroles (see page 4). Press this

button to activate Power Clean (the

indicator lights up).

MULTIZONE

Allows you to choose the washing

zones. Press this button (repeatedly)

to select the wash zones:

both racks

only lower rack

only upper rack

- indicator lits

Quick reference guide

Whirlpool is a registered trademark of Whirlpool USA

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! (see at right for options description) PROGRAM SELECTION BUTTON Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) - see “Table of programs” below. START/RESUME BUTTON Push this button to start the selected program: the indicator lights up and goes off at the end of the program.
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only before the first wash or if water hardness has been changed Water hardness level is factory set for medium-hard water (level 4). Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
PAGE 3
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B.
PAGE 4
How to load the racks UPPER RACK - depending on the model 4 A - Adjustable flaps (2 or 4): in horizontal position for cups/long utensils/stemmed glasses. A - CLOSED A - OPEN TO OPEN A: B - Cutlery basket: can be placed in the upper rack when the “Half load/Multizone” option is selected. The Grid (F) should be removed. CLICK! How to adjust upper rack height (if available). It could be useful to lift up the upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open. To pause the program (e.g.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. How the faults are shown on the display: Function number “F”x - blinking The appliance... ...is not working/will not start - The appliance must be switched on. - Check the household circuit fuse if there is no power supply.
PAGE 7
What to do if... Crockery and cutlery... Possible causes... Solutions... ...salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up. ...have deposits: regeneration salt residue - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly.
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.