Instruction for Use

ManualsBrandsWhirlpool ManualsDomestic AppliancesADG 9041 FD

-1-

Chart

PROGRAMS

SELECTION

BUTTON

Push “Programs” button

(repeatedly) until the

indicator of the required

program lights up (see

“Table of programs” -

next page).

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

MULTIZONE

Allows you to choose the

washing zones. Press this

button (repeatedly) to

select the wash zones:

both racks

only lower rack

only upper rack

(including

cutlery rack)

- indicator lits

DELAYED START

BUTTON

Push the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to 24

hours. With each press of

the button, the delayed

start indicator increases

by one hour and after 24

restarts from 0. Then

press the START button.

The dishwasher will start

after the set time.

ADG 9041

5019 396 01994

POWER CLEAN

MAX

Thanks to the additional

power jets this option

provides a more intensive

and powerful wash in the

lower rack, in the specific

area. This option is

recommended for

washing pots and

casseroles (see page 7).

Press this button to

activate Power Clean (the

indicator lights up).

TABLET SETTING

This setting allows to

optimize the cycle

performances according

the type of detergent

used. Push the Tablet

button for 3 seconds (until

the indicator lights up) if

you are using the

combined detergents in

tablet (rinse aid, salt and

deteregent in 1 dose). If

you are using powder

detergent or liquid

detergent, the Tablet

indicator on the control

panel has to be off.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

START/RESUME

BUTTON

Push this button to start

the selected program: the

indicator lights up and

goes off at the end of the

program.

When the door is opened

during a washing cycle, the

cycle is temporarily

paused: the Start indicator

blinks.

To resume the cycle push

Start button and close the

door within 3 seconds.

CANCEL/OFF

BUTTON

Push this button to switch

off the control panel.

If pressed when a

program is running it

cancels the program

ongoing draining water for

1 minute (0:01 is shown

into the display).

If pressed when the

dishwasher is switched

off, it drains any possible

liquids from dishwasher

(1 minute process).

RINSE AID INDICATOR

When lit (at the end of the

cycle), the rinse aid

dispenser needs to be

refilled.

SALT INDICATOR

When lit (at the end of the

cycle), the salt reservoir

needs to be refilled.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With

“Delayed start” selected it indicates the time remaining until program

start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 9 - chapter

“What to do if...”.

OPERATION

INDICATOR

A LED light projected

on the floor indicates

that the dishwasher is working.

Quick reference guide

Summary of content (12 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED. OPERATION INDICATOR A LED light projected on the floor indicates that the dishwasher is working.
PAGE 2
Chart Quick reference guide Table of programs P Available options Programs Consumption Loading instructions Soaking or hand pre-treatment is no longer needed on any kind of items. Steam is used to soften soil and its action is particularly effective Delay coffee, tea and lipstick stain on glasses and 40-70°C Multizone on cups. Furthermore, thanks to the combination Power Clean with 6th Sense, optimization of time, energy and water is guaranteed because it adapts the washing cycle to the level of soil.
PAGE 3
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only before the first wash or if water hardness has been changed - Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds. The current water hardness setting will be visible on the display. Press the Programs button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the start button will set the level back to 1).
PAGE 4
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B.
PAGE 5
How to load the racks Cutlery rack 4 Position 1 Position 2 A - Two trays to load cutlery Load cutlery with the handle into the pins. Knives or cutlery with bulky handle can be loaded with the head into the pins. This positions is ideal to load both cutlery, and long tools. Adjust the upper rack in lower position before to move the cutlery rack in Position 2 (see description in the following page).
PAGE 6
How to load the racks Upper rack 4 In the upper rack you can load glasses, cups, bowls and, in the right side of the rack, you can load the dessert dishes. Adjustable glass holder - B (provided in some models) helps to load stemmed glasses. You can load dishes up to Ø 20 cm in the upper rack ONLY if the rack is in lower position (see below how to adjust the upper rack).
PAGE 7
How to load the racks Lower rack 4 In the lower rack plates and pots can be loaded. Vertical plate holders (E) can be folded down to create more space to load pots. When the “Half load/Multizone” is selected the cutlery basket - F (provided in some models) can be placed in the lower rack. How to use Power Clean 1. Adjust the Power Clean area (G) folding down the 2. Load pots and casseroles inclined vertically in Power rear plate holders to load pots. Clean area.
PAGE 8
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached Table of programs (page 2). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open. To pause the program (e.g.
PAGE 9
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. How the faults are shown on the display: Function number “F”x - blinking The appliance... ...is not working/will not start ...shows “F6 ...shows “F6 E2” E7” or “F6 E1” Possible causes... E1” 0.5 sec. pause Solutions...
PAGE 10
What to do if... Crockery and cutlery... ...are not perfectly clean/have food residues Possible causes... Solutions... - Too little space between dishes (incorrect - Arrange crockery so that items do not touch each other. Concave items (e.g. arrangement of the concave items in the rack). bowls, cups) must be arranged facing downwards in the rack. - Too little detergent; detergent too old or incorrectly stored.
PAGE 11
What to do if... Crockery and cutlery... Possible causes... Solutions... ...have discoloured plastic parts - Tomato/Carrot juice. - Tomato sauce, for example, can lead to discolouring of plastic parts. Powder detergent is recommended as it allows slightly higher doses to be used for improved whitening. Programs with higher wash temperatures should be used. ...opaque glasses, etc. - Dishes unsuitable for washing in dishwashers (porcelain), - Usage of incorrect programs for glasses.
PAGE 12
Precautions and general recommendations 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.