Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADG 9100 FD

-1-

Chart

(see at right for options description)

PROGRAMME SELECTION BUTTON

Press button “P” (repeatedly) until the

required programme number appears on

the display (see “Table of programmes”

below).

START BUTTON

The indicator lights up during operation,

flashes when a fault occurs and goes off at

the end of the programme.

BUTTON

OFF

BUTTON

FAULT INDICATION AND WASH TIME DISPLAY

In normal operation it indicates the remaining time (h:mm), whereas with

“Delayed start” selected it indicates the time remaining until programme

start (hh).

If “F..” appears on the display, see chapter “What to do if...”.

RESET BUTTON

For programme change or indication of faults.

Press this button to cancel a started programme and selected extra

options. Press this button to cancel the main fault indicators “F..”

also refer to the chapter “What to do if...”. The programme can then

be selected and started.

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional

options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of

the appliance’s automatic calibration system.

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on

the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

Table of programmes

Deter-

gent

Consumption

Programmes

Available

options

Loading instructions Litres Kwh

Minutes

Quickwash 40°C

Delay

Lightly soiled crockery, with no dried-

on food.

Not recommended tablets use.

13.0 0.65 30

Bio

50°C

Delay Normally soiled crockery. X 17.0 1.13 195

Intensive 70°C

Delay

Recommended programme for heavily

soiled crockery, especially suitable for

pots and pans.

X 17.0 1.75 150

Antibacterial

Delay

Normally or heavily soiled crockery,

with additional antibacterial wash.

Programme interruption (e.g. due to

door opening) can compromise

elimination of germs.

X 17.0 1.60 120

Half Load 50°C

Delay

Ideal for washing a half load of lightly

or normally soiled crockery.

X 13.0 0.90 130

5019 396 01760ADG 9100

Options and display description

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE INSTALLATION

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

RINSE AID

INDICATOR

When lit, the rinse aid

dispenser needs to be

refilled.

SALT INDICATOR

When lit, the salt

reservoir needs to be

refilled.

SET THE

DETERGENT

Press this button

(repeatedly) to set the

type of detergent used.

Powder, gel

(standard)

Detergent

with rinse aid

Detergent

with salt +

rinse aid

DELAYED START

BUTTON

Press the button

(repeatedly) to delay

the start of the

programme.

Adjustable from 1 to 24

hours. With each press

of the button, the

delayed start indicator

increases by one hour

and after 24 resets

from 00. Then press

the START button. The

dishwasher will start

after the set time.

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide ON BUTTON FAULT INDICATION AND WASH TIME DISPLAY In normal operation it indicates the remaining time (h:mm), whereas with “Delayed start” selected it indicates the time remaining until programme start (hh). If “F..” appears on the display, see chapter “What to do if...”. START BUTTON The indicator lights up during operation, flashes when a fault occurs and goes off at the end of the programme.
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results * only before the first wash or if the water hardness has been changed Switch on the appliance - Select the 2nd programme “P2” - consult the table of programmes. Press the START button for at least 5 seconds until the START indicator lamp flashes. The water hardness setting is shown on the display (if present) or the START button flashes.
PAGE 3
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 2 Visual indicator B Add rinse aid to max. line ~100 ml If required, open the cover (press lever). Rinse aid indicator (depending on model) The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the lever to open the cover. Using a coin or similar object, turn the arrow to the desired setting.
PAGE 4
How to load the racks How to load UPPER RACK 4 B - Adjustable flaps: In horizontal position for cups/long utensils, in raised position for plates and stemware. (In some models only) A - Multipurpose support: Different positions for long utensils, cups and glasses. How to adjust upper rack height (if available) - It could be useful to lift up upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select programme 6 Quick, permanent or alternating Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the panel (page 1). Choose programme according to the attached Table of programmes (page 1). Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open.
PAGE 6
What to do if... If a fault occurs, before restoring normal appliance operation contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... ...is not working/will not start ...shows “F1” on the display or the START indicator lamp flashes once ...shows “F4” on the display or the START indicator lamp flashes 4 times ...
PAGE 7
What to do if... Crockery and cutlery... ...salt indicator lit ...have deposits: regeneration salt residue Possible causes... Solutions... - Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up. - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly.
PAGE 8
Disconnect the mains plug What to do if... If, after carrying out the above checks, the fault persists, switch off the appliance, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).