Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADG 9190/1

WH/II/FD/GB

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Press the

button.

(The first time you use the appliance

and when using a different type of

detergent)

1. Select the third programme from the

top in the relative table.

2. Press the Start button for about 7

seconds until the display changes.

3. Select the required detergent with the

Start button: “3h” = 2in1, “6h” = 3in1, “9h” = All in 1, all three LEDs

on = soap powder (factory setting).

4. Switch the appliance off and then switch it on again. The type of detergent

selected is shown by the relative LED for approximately three seconds.

For dosage of powder detergent in compartment

and

refer to the

programmes table.

Mechanical indicator

Electric indicator on control panel (if provided).

On models with water softener

system only.

Mechanical indicator

. Electric

indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

The last programme selected will light up.

Press

or until the selected programme lights up.

If necessary the corresponding indicator lights up.

The selected programme is

then memorised (even in the

event of power failure).

- Only open the dishwasher if necessary

(Warning: beware of hot steam).

- If the appliance is switched off during a

wash cycle, when switched on again it

will resume the cycle from where it was

interrupted.

At the end of the programme an acoustic signal will sound.

Only after the START button has switched off: press the

OFF

button.

All the indicator lamps switch off.

Warning: When the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

Open the door,

switch on the appliance

Select, save, and

supply the detergent

ABC

Check the rinse aid level

Check the

regeneration salt level

Load the racks

Select a programme

Select additional options

Press the Start button

“Change programme in progress”

Press the START button for 2 sec. until the

Start indicator lamp switches off.

Select another programme and press the

START button again.

Turn on the water tap,

close the dishwasher door

Wash cycle

Switch off the appliance

Turn off the water tap,

unload the racks

Summary of content (4 pages)

PAGE 1
How to use the appliance Further indications are given in the single chapters and in the user instructions. Open the door, switch on the appliance Select, save, and supply the detergent Check the rinse aid level Check the regeneration salt level Load the racks Select a programme Select additional options Press the ON button. (The first time you use the appliance and when using a different type of detergent) A BC 1. Select the third programme from the top in the relative table. 2.
PAGE 2
Dishwasher loading instructions and racks provided Upper rack: depending on the model Multi-purpose support (A): 1) Depending on the position, for longhandles utensils, cups and glasses. May be used in three different positions. Crockery holders (B): Depending on the position, for example plates, cups and long-stemmed glasses. Revolving glass support (C): 2) Depending on the position, for example small or long-stemmed glasses. Long-handled utensils (e.g.
PAGE 3
What to do if... If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem (* see also the corresponding chapter in the user instructions). Problem The appliance is not working If crockery is not perfectly dry If crockery is not perfectly clean Cause Remedy • No water supply. • Open the tap. • The appliance does not load sufficient water. • Clean the water supply tap filter. • Ensure there are no kinks in the water hose.
PAGE 4
Before using the dishwasher, read the user instructions! GB Quick Reference Guide ADG 9190 Options 3) On button “Delayed start” button The wash cycle can be programmed to start after 3-6-9 hours. Then press the Start button. The wash programme will start at the set time. Off button Programme selection button Start button Switches “on” when the dishwasher is operating. Flashes when a fault occurs. Switches off at the end of the programme.