Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADG 9449 FD

EN -1-

Chart

(see at right for options description)

PROGRAM SELECTION

BUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the program.

When the door is opened during a washing cycle, the

cycle is temporarily paused: the Start indicator blinks.

To resume the cycle push Start button and close

the door within 3 seconds.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may

vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic

calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/

Standard loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

* Power consumption in: Left-on mode: 1.08 W / Off-mode: 0.40 W.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

Sensor 40°-70°C

Delay,

Multizone,

Antibacterial rinse

Recommended program for routine

washes, with dried-on food.

X 7.5-13 0.95-1.45 85-175 Full

Pre-Wash cold

Delay,

Multizone

Crockery to be washed later. – 4.0 0.01 14-16 NO

Fragile 40°C

Delay,

Multizone

Light soiling, for example glasses

and cups.

X 10.5 0.85 105-114 Light

Rapid 45°C

Delay,

Multizone

Lightly soiled crockery, with no

dried-on food.

X 11.0 0.85 30-50 NO

Eco

50°C

Delay,

Multizone,

Antibacterial rinse

Normally soiled crockery.

Standard program the most efficient

in terms of its combined energy and

water consumption.

X 9.0 0.92 240 Full

Daily 60°C

Delay,

Multizone,

Antibacterial rinse

Normally soiled crockery. X 11.0 1.30 80-95 Full

Silent 50°C

Delay,

Multizone

Normally soiled crockery, gentle

and quiet thanks to the lower spray

pressure.

X 14.0 1.20 290-299 Light

Steam

Delay,

Multizone,

Antibacterial rinse

Program including steam action

dedicated for heavily soiled

crockery, pots and pans. Soaking or

hand pretreatment is no longer

needed.

X 14.5 1.75 180-190 Full

5019 300 02752

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING THE

CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER

30 SECONDS IF NO CYCLE HAS STARTED.

MULTIZONE

Allows you to choose the washing

zones. Press this button (repeatedly)

to select the wash zones:

both racks

only lower rack

only upper rack

ANTIBACTERIAL RINSE

This function activates an antibacterial

rinse at the end of the wash cycle,

guaranteeing a further reduction of

bacteria. Press the button to activate

or deactivate the function.

This function can be used with the

programs indicated in the table of

programs. The dishwasher door must

be kept shut for the entire duration of

the program in order to guarantee

reduction of bacteria. If the door is

opened the indicator lamp starts

flashing.

SALT INDICATOR

When lit (at the end of the cycle), the salt

reservoir needs to be refilled.

RINSE AID INDICATOR

When lit (at the end of the cycle), the rinse aid

dispenser needs to be refilled.

- indicator lits

TABLET SETTING

This setting allows to

optimize the cycle

performances according

the type of detergent

used. Push the Tablet

button for 3 seconds

(until the indicator lights

up) if you are using the

combined detergents in

tablet (rinse aid, salt and

detergent in 1 dose).

If you are using powder

detergent or liquid

detergent, the Tablet

indicator on the control

panel has to be off.

DELAYED START

BUTTON

Push the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to

24 hours.

With each press of the

button, the delayed start

indicator increases by

one hour and after

24 restarts from 0.

Then press the START

button.

The dishwasher will

start after the set time.

OPERATION

INDICATOR

A LED light projected on

the floor indicates that

the dishwasher is

working.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

Quick reference guide

Whirlpool is a registered trademark of Whirlpool USA

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! (see at right for options description) PROGRAM SELECTION BUTTON Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) - see “Table of programs” below. START/RESUME BUTTON Push this button to start the selected program: the indicator lights up and goes off at the end of the program.
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only before the first wash or if water hardness has been changed Water hardness level is factory set for medium-hard water (level 4). - Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds. - The current water hardness setting will be visible on the display. - Press the PROGRAM Selection button to increase setting.
PAGE 3
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B.
PAGE 4
How to load the racks UPPER RACK - depending on the model 4 A - Adjustable flaps (2 or 4): in horizontal position for cups / long utensils / stemmed glasses. A - CLOSED A - OPEN B - Cutlery basket: can be placed in the upper rack when the “Half load/Multizone” option is selected. The Grid (F) should be removed. TO OPEN A: CLICK! C D How to remove the upper rack (if available) It could be useful to remove the upper rack to load bulky items in the lower rack.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. For hygienic reasons it is recommended to run a high-temperature cycle (e.g. Intensive 65) at least once per month.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes... Solutions... salt indicator is lit - rinse aid indicator is lit - Rinse aid dispenser is empty. - Refill dispenser with rinse aid (for more information - see page 3) ...
PAGE 7
What to do if... Crockery and cutlery... ...have deposits: regeneration salt residue Possible causes... Solutions... - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly. - Not enough rinse aid. - If you use a combined action detergent, try adding more rinse aid. - Plastic containers dry badly.
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.