Instruction for Use

ManualsBrandsWhirlpool ManualsOtherADG 9643

Whirlpool is a registered trademark of Whirlpool USA

5019 396 01194

Before using the dishwasher, read the installation and maintenance instructions carefully!

ADG 9643

1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads, extra

functions, different settings, water supply temperatures, water hardness and power supply voltage.

2) Programme for energy data label in conformity with EN 50242. - Information for Test Laboratories:

for detailed information on the EN/Standard

loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been proven in collaboration with the Pasteur Institute of Lille (France), in conformity with. Standard NF EN 13697 of

November 2001.

1. OVERVIEW

Programme selection button

Press the button (repeatedly) until the indicator lamp of the

desired programme lights up (see table 1.1).

At the end of the wash cycle, the last programme selected is

memorized.

Half Load/Multizone

Load the upper or lower rack only.

Factory setting = Wash upper and lower rack (both indicator

lamps light up)

Press once = Wash lower rack (the indicator lamp lights up)

Press twice = Wash upper rack (the indicator lamp lights up)

At the end of the programme, the most recently selected

setting remains memorised.

If the upper rack is not being washed, the “Wash lower rack”

indicator lamp should be lit.

Antibacterial rinse

This function activates an antibacterial rinse at the end of the

wash cycle, guaranteeing a further reduction of bacteria. Press

the button to activate or deactivate the function. This function

can be used with those programmes marked with the relative

symbol in table 1.1.

The dishwasher door must be kept shut for the entire duration

of the programme in order to guarantee reduction of bacteria.

If the door is opened the indicator lamp starts flashing.

At the end of the programme, the most recently selected

setting remains memorised.

Detergent setting upon initial use and when using a different

type of detergent

Indicator lamp off = Powder/gel detergent (factory setting).

If using combined detergents, press and hold the button for 3

seconds; the indicator lamp lights up = rinse aid and salt

indicators are deactivated.

From water hardness level 5, the salt indicator remains active.

At the end of the programme, the most recently selected

setting remains memorised.

Fault indication and wash time display

In normal operation it indicates the remaining time (h:min),

whereas with “Delayed start” selected it indicates the time

remaining until programme start (e. g. h 01). If using a sensor

programme, a dotted line indicates that the calibration process

is underway (lasting up to 20 minutes).

In the presence of a fault indication “F.. / E..”, refer to Section 5

“What to do if...”.

Delayed Start button

Push the button (repeatedly) to delay the start of the

programme. Adjustable from 1 to 24 hours. With each

successive touch of the button, the delayed start indicator

increases by 1 hour, and after “h 24” returns to “h 00”. Then

press the START button. The wash programme will start after

the set time.

Start/Resume button

The indicator lamp lights up during operation, flashes when the

programme is interrupted before completion and switches off at

the end of the programme.

Cancel/Off button

Press the button to switch the dishwasher off or to interrupt the

selected programme.

If the Cancel/Off indicator lamp flashes repeatedly, this indicates

a fault: see chapter 5 “What to do if...”.

Salt level indicator and rinse aid level indicator

These light up at the end of the programme if salt or rinse aid

needs topping up.

Only add just before starting a wash cycle.

Operation indicator

A LED light projected on the floor indicates that the dishwasher

is working.

Table 1.1.

Programme Table

Detergent

compartment

Consumption

Programmes

Selectable

options

Description of programme

large small Litres kWh Minutes

Sensor 40-70°C

Normally or heavily soiled crockery,

including pots and pans.

X X 7-14 0.99-1.80 70-185 ±

Pre-Rinse cold

Crockery to be washed later. — — 4.0 0.03

14 ±

Quickwash 45°C

Lightly soiled crockery, with no dried-on

food.

X — 11.0 0.80 30 ±

Eco

50°C

Normally soiled crockery. Energy-saving

programme.

X X 11.0 0.98 170 ±

Rapid daily 60°C

Normally soiled crockery. X — 10.0 1.30 80 ±

Intensive 70°C

Recommended programme for heavily

soiled crockery, especially suitable for pots

and pans.

X X 14.0 1.55 155 ±

Summary of content (8 pages)

PAGE 1
Before using the dishwasher, read the installation and maintenance instructions carefully! GB ADG 9643 1. OVERVIEW Programme selection button Press the button (repeatedly) until the indicator lamp of the desired programme lights up (see table 1.1). At the end of the wash cycle, the last programme selected is memorized. Half Load/Multizone Load the upper or lower rack only.
PAGE 2
. QUICK REFERENCE GUIDE Detailed instructions are given on the following pages; also see section “5. What to do if...”. 1. Switch the appliance on The dishwasher switches on automatically when any button is pressed, except for the button. If no button is pressed within 30 seconds, the appliance switches to Energy Saving mode. 2. Select the right type of detergent Depending on the dishwasher model 3. Fill the detergent dispenser 4. Check the rinse aid level 5. Set the water hardness level 6.
PAGE 3
. HOW TO USE THE APPLIANCE HOW TO FILL THE DETERGENT DISPENSER Only fill the detergent dispenser prior to starting a wash programme. Only use detergents specially recommended for dishwashers, observing the manufacturer’s recommended dosage. Observe the manufacturer’s safety warnings! Press the left button (button 1) on the dispenser to open the detergent dispenser compartments. a. Powder/gel/tabs Fill the detergent dispenser compartments in accordance with the wash programme selected (table 1.1).
PAGE 4
3. HOW TO USE THE APPLIANCE HOW TO CHECK/FILL/ADJUST SALT Only use regeneration salt specifically intended for dishwashers. a. How to check the salt level Depending on the model, check the visual indicator . The window on the salt reservoir cap is clear when salt needs to be added and coloured when the salt present is sufficient. In the case of appliances with an electric indicator on the control panel, the salt indicator lights up at the end of the wash cycle when salt needs to be added. b.
PAGE 5
3. HOW TO USE THE APPLIANCE HOW TO LOAD THE RACKS CUTLERY RACK: May be used in two different positions. Position 1 Position 2 In position 2 the upper rack must be lowered (see “Upper rack height adjustment” C below). For optimum washing results, position cutlery as shown (handles of spoons facing inwards). Beware of sharp/pointed items. Risk of injury! Cutlery holder A May be removed individually, depending on upper rack load.
PAGE 6
4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packaging The packaging materials are 100% recyclable and marked with the recycling symbol . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher has not been damaged during shipping and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3.
PAGE 7
5. WHAT TO DO IF... If a fault occurs, before contacting the After-Sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes/solutions ...is not working/will not start - The appliance must be switched on. Check the household circuit fuse if there is no power supply. The dishwasher door must be closed.
PAGE 8
5. WHAT TO DO IF... Crockery and cutlery ... Possible causes/solutions ...are not perfectly clean/have food residues - ...have deposits: - regeneration salt residue - In the event of frequent use of low temperature programmes (50°C or lower) (if available), every now and again select a higher temperature programme The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”).