Operation Manual

ManualsBrandsWhirlpool ManualsDishwashersADG SPACE

-1-

Chart

PROGRAMME SELECTION BUTTON

Press button “P” (repeatedly) until the indicator of the required programme lights up (see “Table of

programmes” below).

START BUTTON

The indicator lights up during operation, flashes when a fault occurs and goes off at the end of the

programme.

START BUTTON RESET FUNCTION

Press this button for at least 2 seconds; the selected programme and options are cancelled. Main

failure displays (repeated flashing of the START indicator lamp) can be cancelled by RESETTING.

Detailed instructions are given in chapter “What to do, if...”.

BUTTON

OFF

BUTTON

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional

options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of

the appliance’s automatic calibration system.

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information

on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

Table of programmes

Detergent

Consumption

Programmes Loading instructions Litres kWh

Minutes

Pre-Wash cold

Crockery to be washed later. — 4.0 0.03 14

Quickwash 40°C

Lightly soiled crockery, with no dried-

on food. * Use of tablets not

recommended.

X * 10.0 0.65 30

Eco

50°C

Normally soiled crockery.

Energy-saving programme.

X 12.0 1.05 165

Antibacterial

Normally or heavily soiled crockery,

with additional antibacterial wash.

Programme interruption (e.g. due to

door opening) can compromise

elimination of germs.

X 13.0 1.50 115

Intensive 70°C

Recommended programme for heavily

soiled crockery, especially suitable for

pots and pans.

X 14.0 1.55 155

5019 396 01745ADG Space

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE INSTALLATION

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide ON BUTTON PROGRAMME SELECTION BUTTON Press button “P” (repeatedly) until the indicator of the required programme lights up (see “Table of programmes” below). START BUTTON The indicator lights up during operation, flashes when a fault occurs and goes off at the end of the programme. START BUTTON RESET FUNCTION Press this button for at least 2 seconds; the selected programme and options are cancelled.
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results In order to always ensure the best cleaning results, you NEED to set: DETERGENT type and WATER HARDNESS. 1. Select 3rd programme 2. Press START button 3a. Check your (see Table of programmes for 7 seconds detergent type... - page 1) Detergent types 3b....and set it on your dishwasher using the START button (as per table below) 4. Remember to use salt and rinse aid when needed (as indicated below) 5.
PAGE 3
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 1 The salt level indicator lamp may remain lit for the duration of several wash cycles. If the water hardness level falls within category (soft), no salt is required. Salt indicator (depending on the model) Visual indicator (depending on model). Screw on the cap. Salt residues around cap need to be removed. Add salt (never add detergent!). min. 1.5 kg max.
PAGE 4
How to load CUTLERY RACK 4 How to load LOWER RACK Position 1 Position 2 A - Two trays for cutlery E - Vertical plate holders: They can be folded down to load pots. E To allocate the cutlery rack in position 2 bring the upper rack down (see description at right). How to remove cutlery and/or upper rack (if available) It could be useful to remove cutlery rack to load stem glasses in upper rack and/or remove upper rack to load bulky items in lower rack.
PAGE 5
Select programme 6 Quick, permanent or alternating Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the panel (page 1). Choose programme according to the attached Table of programmes (page 1). Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open.
PAGE 6
What to do if... If a fault occurs, before restoring normal appliance operation.contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... ...is not working/will not start ...shows “F1” on the display or the START indicator lamp flashes once ...shows “F4” on the display or the START indicator lamp flashes 4 times ...
PAGE 7
What to do if... Crockery and cutlery... ...salt indicator lit ...have deposits: regeneration salt residue Possible causes... Solutions... - Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up. - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly.
PAGE 8
Disconnect the mains plug What to do if... If, after carrying out the above checks, the fault persists, switch off the appliance, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).