ADL 101 IT Italiano DE Deutsch Istruzioni per l’uso Gebrauchsanleitung LAVASTOVIGLIE - Sommario GESCHIRRSPÜLER – Inhaltsverzeichnis Istruzioni per l’uso, 1 Istruzioni di sicurezza importanti, 2-3 Assistenza, 10 Scheda prodotto, 11 Installazione, 13-14 Descrizione dell’apparecchio,15 Sale Rigenerante e Brillantante, 16 Caricare i cesti, 17-18 Detersivo e uso della lavastoviglie, 19 Programmi, 20 Programmi Speciali ed Opzioni, 21 Manutenzione e cura, 22 Anomalie e rimedi, 23 EN English Operating in
LEGENDA SIMBOLI/LEGEND OF SYMBOLS/SYMBOLERKLÄRUNG/LEYENDA DE LOS SÍMBOLOS Attenzione/Warning/Warnung/Advertencia Messa a Terra/Grounding/Erdung/Conexión a tierra Rischio Elettrico/Electrical Hazard/Stromschlag/Peligro eléctrico Smaltimento/Waste/Abfall/Desechos Rispettare l’ambiente/Safeguarding the environment/Umweltschutz/Protección del medio ambiente Riciclare/Recycling/Recycling/Reciclado Usare i guanti/Use gloves/Verwenden Sie Handschuhe/Utilizar guantes IT ISTRUZIONI DI SICUREZZA IMPORTANTI Prima d
a terra ridurrà il rischio di scossa elettrica fornendo una via di minore resistenza della corrente elettrica. L’elettrodomestico è dotato di un cavo di alimentazione provvisto di conduttore di terra e di spina di terra. • La spina deve essere collegata ad una presa adeguata, installata e messa a terra nel rispetto di tutte le normative e disposizioni locali. • Non servirsi di prolunghe, adattatori e spine adattatrici per collegare l’elettrodomestico alla presa elettrica.
EN IMPORTANTSAFETYINSTRUCTIONS Read the instructions carefully before using, as they include important information on safe installation, use and maintenance. Keep this instruction manual in a safe place for future reference. If the appliance is sold, given away or moved, make sure the manual is kept with the machine.
installation. • When loading items to be washed: 1 - Locate sharp items so that they are not likely to damage the door seal; 2 - WARNING: Knives and other utensils with sharp points must be loaded in the cutlery basket with their points/blades down or placed in a horizontal position with the sharp end facing away from the front of the appliance. • Use only detergent and rinse additives designed for an automatic dishwasher. • WARNING: Some dishwasher detergents are strongly alkaline.
• Reinigungs- und Wartungsarbeiten sollten nicht von Kindern ohne Aufsicht durchgeführt werden. • Das Gerät darf nicht im Freien, auch nicht in überdachten Bereichen, aufgestellt werden. Es ist extrem gefährlich, wenn die Maschine Regen oder Unwettern ausgesetzt ist. • Lagern Sie keinen brennbaren Materialen in der Nähe des Geräts. • Das Wasser im Gerät ist kein Trinkwasser.
Stromversorgungskabel nicht stark geknickt oder gequetscht werden. Manipulieren Sie nicht die Steuerung. • Entsorgen Sie das Verpackungsmaterial gemäß den örtlichen Bestimmungen, dass es recycelt werden kann. • Benutzen Sie den Geschirrspüler nur für den vorgesehenen Verwendungszweck. • Das Gerät muss mit neuen Schläuchen an die Wasserleitung angeschlossen werden. Das alte Schlauchset darf nicht wiederverwendet werden. • Die maximale Anzahl von Gedecken ist im Produktdatenblatt angegeben.
• • • • • • • • • • • • 8 desconectarlo también para cualquier trabajo de mantenimiento en caso de defectos de funcionamiento. Las reparaciones y las modificaciones técnicas deben ser realizadas exclusivamente por un técnico cualificado. Al desconectar el aparato, tirar de la clavija para extraerla de la toma. No tirar del cable. • Para evitar el riesgo de cortes, utilizar guantes especiales durante el ensamblaje del aparato.
• Para información más detallada sobre la manipulación y el reciclado del producto, contactar con las autoridades locales que se ocupan de la recogida selectiva, o con la tienda donde se haya adquirido el aparato. ELIMINACIÓN DEL EMBALAJE •El embalaje se puede reciclar al 100%, como indica el símbolo. No abandonar en el ambiente ninguna parte del embalaje. Para la eliminación del embalaje respetar los reglamentos establecidos por las autoridades locales.
IT Assistenza Prima di contattare l’Assistenza: • Verificare se l’anomalia può essere risolta da soli (vedi Anomalie e Rimedi). • Riavviare il programma per controllare se l’inconveniente è stato ovviato. • In caso negativo, contattare il Servizio Assistenza Tecnica Autorizzato. Non ricorrere mai a tecnici non autorizzati. Comunicare: • il tipo di anomalia; • il modello della macchina (Mod.); • il numero di serie (S/N).
IT Scheda prodotto Scheda prodotto Marchio IGNIS Modello ADL 101 Capacità nominale in numero di coperti standard (1) 10 Classe di efficienza energetica su una scala da A+++ (bassi consumi) a D (alti consumi) A+ Consumo energetico annuo in kWh (2) 237 Consumo energetico del ciclo di lavaggio standard in kWh 0.83 Consumo di potenza nel modo spento in W 0.5 Consumo di potenza nel modo lasciato acceso in W 5.
DE Datenblatt Datenblatt Marke IGNIS Modell ADL 101 Nennkapazität in Standardgedecken für den Standardreinigungszyklus (1) 10 Energieeffizienzklasse (A+++ niedriger Verbrauch) bis D (hoher Verbrauch) A+ Energieverbrauch pro Jahr in kWh (2) 237 Energieverbrauch Standardreinigungszyklus in kWh 0.83 Gewichtete Leistungsaufnahme im Aus-Zustand in W 0.5 Gewichtete Leistungsaufnahme im unausgeschalteten Zustand in W 5.
Installazione In caso di trasloco tenere l’apparecchio in posizione verticale; se fosse necessario, inclinarlo sul lato posteriore. Collegamenti idraulici L’adattamento degli impianti idraulici per l’installazione deve essere eseguito solo da personale qualificato. I tubi di carico e di scarico dell’acqua possono essere orientati verso destra o sinistra per consentire la migliore installazione. I tubi non devono essere piegati o schiacciati dalla lavastoviglie.
IT Avvertenze per il primo lavaggio Dopo l’installazione, rimuovere i tamponi posizionati sui cesti e gli elastici di trattenimento sul cesto superiore (dove presenti). Impostazioni addolcitore acqua Prima di avviare il primo lavaggio, impostare il livello di durezza dell’acqua di rete. (vedi capitolo Brillantante e sale rigenerante) Il primo caricamento del serbatoio dell’addolcitore deve avvenire con acqua, poi introdurre circa 1 Kg. di sale; è normale che l’acqua fuoriesca.
Descrizione dell’apparecchio Vista d’insieme IT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Sale rigenerante e Brillantante IT Usare solo prodotti specifici per lavastoviglie. Non usare sale alimentare o industriale. Seguire le indicazioni riportate sulla confezione. Se si usa un prodotto multifunzione, si consiglia comunque di aggiungere il sale, specie se l’acqua è dura o molto dura. (Seguire le indicazioni riportate sulla confezione). Non aggiungendo né sale né brillantante è normale che le spie MANCANZA SALE e MANCANZA BRILLANTANTE rimangano accese.
Caricare i cesti Suggerimenti Prima di caricare i cesti, eliminare dalle stoviglie i residui di cibo e vuotare bicchieri e i contenitori dei liquidi rimasti. Non è necessario un risciacquo preventivo sotto acqua corrente. Sistemare le stoviglie in modo che siano ben ferme e non si ribaltino, i contenitori siano disposti con l’apertura rivolta in basso e le parti concave o convesse in posizione obliqua, per permettere all’acqua di raggiungere tutte le superfici e di defluire.
IT Regolare l’altezza del cesto superiore Il cesto superiore è regolabile in altezza: in posizione alta quando nel cesto inferiore si vogliono sistemare stoviglie ingombranti; in posizione bassa, in modo da sfruttare gli spazi delle ribaltine creando più spazio verso l’alto. Si consiglia vivamente di non regolare in nessun caso la posizione in altezza a cestello carico. Non sollevare o abbassare MAI il cesto su un solo lato. Stoviglie non idonee • Posate e stoviglie di legno.
Detersivo e uso della lavastoviglie Caricare il detersivo Il buon risultato del lavaggio dipende anche dal corretto dosaggio del detersivo, eccedendo non si lava in modo più efficace e si inquina l’ambiente. A seconda del grado di sporco, il dosaggio può essere adattato al singolo caso con un detersivo in polvere o liquido. Solitamente per uno sporco normale, utilizzare circa 25 gr. (detersivo in polvere), o 25ml (detersivo liquido). Se si impiegano le pastiglie ne basta una.
Programmi IT I dati dei programmi sono misurati in condizioni di laboratorio secondo Norma europea EN 50242. A seconda delle diverse condizioni di utilizzo, la durata e i dati dei programmi possono variare. Asciugatura Opzioni Durata dei programmi ore:min. Consumo acqua (l/ciclo) Consumo energia (KWh/ciclo) 1. Eco Si Partenza Ritardata – Tab – Mezzo Carico 03:00 10 0,83 2. Intensivo Si Partenza Ritardata – Tab – Mezzo Carico 02:30 14 1,3 3.
Programmi speciali ed Opzioni Note: le migliori prestazioni dei programmi “Smart Daily” e “Rapido”, si ottengono preferibilmente rispettando il numero di coperti specificati. Per consumare di meno usa la lavastoviglie a pieno carico. Nota per i laboratori di Prove: per informazioni sulle condizioni della prova comparativa EN, farne richiesta all’indirizzo: contact_ignis@ignis.
Manutenzione e cura IT Escludere acqua e corrente elettrica • Chiudere il rubinetto dell’acqua dopo ogni lavaggio per eliminare il pericolo di perdite. • Staccare la spina dalla presa di corrente quando si pulisce la macchina e durante i lavori di manutenzione. Pulire la lavastoviglie • La superficie esterna e il pannello di controllo possono essere puliti con un panno inumidito con acqua non abrasivo. Non usare solventi o abrasivi.
Anomalie e rimedi Può accadere che l’apparecchio non funzioni. Prima di telefonare all’Assistenza controllare che non si tratti di un problema facilmente risolvibile aiutandosi con il seguente elenco. Anomalie: Possibili cause / Soluzione: La lavastoviglie non parte o non risponde ai comandi • Spegnere la macchina con il tasto ON/OFF, riaccendere dopo un minuto circa e reimpostare il programma. • La spina non è ben inserita nella presa di corrente. • La porta della lavastoviglie non è ben chiusa.
Installation EN If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back. Connecting the water supply Adaptation of the water supply for installation should only be performed by a qualified technician. The water inlet and outlet hoses may be positioned towards the right or the left in order to achieve the best possible installation. Make sure the dishwasher does not bend or squash the hoses.
Advice regarding the first wash cycle After the installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack (if any). Water softener settings Before starting the first wash cycle, set the hardness level of the water from the mains supply. (see chapter Rinse aid and refined salt). First load the softener tank with water, then introduce about 1 kg of salt. It is perfectly normal for water to flow out. As soon as this procedure is complete, run a wash cycle.
Description of the appliance EN Overall view 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Refined Salt and Rinse Aid Only use products which have been specifically designed for dishwashers. Do not use table salt or industrial salt. Follow the instructions given on the packaging. If you are using a multi-function product, we recommend that you add salt in any case, especially if the water is hard or very hard. (Follow the instructions given on the packaging.) If you do not add salt or rinse aid, the LOW SALT and LOW RINSE AID indicator lights will remain lit.
Loading the racks EN Tips Before loading the racks, remove all food residues from the crockery and empty liquids from glasses and containers. No preventive rinsing is needed under running water. Arrange the crockery so that it is held in place firmly and does not tip over; and arrange the containers with the openings facing downwards and the concave/convex parts placed obliquely, thus allowing the water to reach every surface and flow freely.
Adjusting the height of the upper rack The height of the upper rack can be adjusted: high position to place bulky crockery in the lower rack and low position to make the most of the tip-up compartments by creating more space upwards. It is strongly recommended to never adjust height position when the rack is loaded. NEVER raise or lower the rack on one side only. Unsuitable crockery • Wooden crockery and cutlery. • Delicate decorated glasses, artistic handicraft and antique crockery.
Detergent and dishwasher use EN Measuring out the detergent Good washing results also depend on the correct amount of detergent being used. Exceeding the stated amount does not result in a more effective wash and increases environmental pollution. The amount can be adjusted to the soil level. In the case of normally soiled items, use approximately either 25g (powder detergent) or 25ml (liquid detergent). If tablets are used, one tablet will be enough.
Wash cycles Wash-cycle data is measured under laboratory conditions according to European Standard EN 50242. Based on the different conditions of use, the wash-cycle duration and data can change. Wash cycle which include drying 1. Eco EN Options Approximate duration of wash cycles h:min. Water consumption (l/cycle) Energy consumption (KWh/cycle) Yes Start Delay – Half Load - Tab 03:00 10 0,83 2. Intensive Yes Start Delay - Half Load - Tab 02:30 14 1,3 3.
Special wash cycles and Options EN Notes: Optimum performance levels when using the “Smart Daily” and “Rapid” cycles can be achieved by respecting the specified number of place settings. To reduce consumption even further, only run the dishwasher when it is full. Tablet option (Tab) This option optimises washing and drying results. When using multi-functional tablets, press the TABLET button; the corresponding symbol will light up. If the button is pressed again, the option will be deselected.
Care and maintenance Shutting off the water and electricity supplies • Turn off the water tap after every wash cycle to avoid leaks. • Always unplug the appliance when cleaning it and when performing maintenance work. Cleaning the dishwasher • The external surfaces of the machine and the control panel can be cleaned using a non-abrasive cloth which has been dampened with water. Do not use solvents or abrasive products.
Troubleshooting EN Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance. Problem: Possible causes / Solutions: The dishwasher does not start • The water supply tap is not turned on. or cannot be controlled. • Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately one minute and reset the wash cycle. • The appliance has not been plugged in properly or another electricity socket should be used.
Installation Im Falle eines Umzugs sollte das Gerät möglichst in vertikaler Position transportiert werden, falls erforderlich, neigen Sie das Gerät zur Rückseite hin. Der Versorgungsschlauch darf auf keinen Fall abgeschnitten werden: er enthält nämlich Strom führende Teile. Wasseranschlüsse Die Anpassung der Elektro- und Wasseranlagen zur Installation des Gerätes darf nur durch Fachpersonal erfolgen.
DE Hinweise zur ersten Inbetriebnahme Nach Abschluss der Installation die Puffer an den Körben und die Rückhaltegummis vom oberen Korb (wenn vorhanden) entfernen. Einstellungen Wasserenthärter Vor dem ersten Start muss die Wasserhärte des Wassers aus dem Netz eingestellt werden. (siehe Kapitel Klarspüler und Regeneriersalz) Wenn der Wasserenthärtebehälter das erste Mal befüllt wird, muss zunächst Wasser eingefüllt werden. Dann erst etwa 1 kg Salz hinzufügen.
Beschreibung Ihres Geschirrspülers Geräteansicht DE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Regeneriersalz und Klarspüler DE Verwenden Sie bitte nur Spezialprodukte für Geschirrspüler. Verwenden Sie bitte kein Kochsalz oder Industriesalz. Bitte befolgen Sie die auf der Verpackung befindlichen Anweisungen. Sollten Sie ein Multifunktionsprodukt verwenden, empfehlen wir dennoch den Zusatz von Regeneriersalz, besonders bei hartem oder sehr hartem Wasser. (Bitte befolgen Sie die auf der Verpackung befindlichen Anweisungen).
Beladen der Körbe Hinweise Bevor Sie das Geschirr in den Geschirrspüler einräumen, befreien Sie es von Speiserückständen und entleeren Sie Gläser und Behälter von Flüssigkeitsresten. Es ist nicht notwendig, das Geschirr unter fließendem Wasser vorzuspülen. Stellen Sie das Geschirr so ein, dass es fest steht und nicht umfallen kann.
DE Höheneinstellung des Oberkorbes Ungeeignetes Geschirr Der Oberkorb kann in der Höhe verstellt werden: stellen Sie ihn in die oberste Position, wenn Sie großes Geschirr in den Unterkorb einräumen wollen. Wenn Sie eher die klapparen Bereiche nutzen wollen, dann stellen Sie ihn in die untere Position. • Besteck und Geschirr aus Holz. • Empfindliche Dekorgläser, handgemachte Teller und antikes Geschirr. Die Dekore sind nicht spülmaschinenfest. • Nicht temperaturbeständige Kunststoffteile.
Spülmittel und Verwendung des Geschirrspülers Einfüllen des Spülmittels Ein gutes Spülergebnis hängt auch von einer korrekten Spülmitteldosierung ab. Eine zu hohe Dosierung ist nicht gleichzusetzen mit einem besseren Spülergebnis, man belastet dadurch nur die Umwelt. Die Dosierung kann dem jeweiligen Verschmutzungsgrad angepasst werden. Bei einer normalen Verschmutzung ca. 25 g (in Pulverform) bzw. 25 ml (flüssig) verwenden. Werden Spülmitteltabs verwendet, reicht ein Tab aus.
Programme DE Die Programmdaten sind Labormessdaten, die gemäß der europäischen Vorschrift EN 50242 erfasst wurden. Je nach den unterschiedlichen Einsatzbedingungen können die Dauer und die Daten der Programme anders ausfallen. Trocknen Optionen Programmdauer Stunden:Min. Wasserverbrauch (l/Zyklus) Energieverbrauch (KWh/Zyklus) 1. Eco Ja Startverzögerung – Halbe Füllmenge – Tab 03:00 10 0,83 2. Intensiv Ja Startverzögerung – Halbe Füllmenge – Tab 02:30 14 1,3 3.
Sonderprogramme und Optionen Hinweis: Die optimale Leistung der Programme "Smart Daily und Rapid" ist dann gewährleistet, wenn die Anzahl der angegebenen Maßgedecke eingehalten wird. Das Für einen geringeren Verbrauch sollte die Maschine voll beladen werden. Hinweis für die Prüflabors: Informationen hinsichtlich der Bedingungen des EN-Vergleichstests sind unter nachfolgender Adresse anzufordern: contact_ignis@ignis.
Reinigung und Pflege DE Abstellen der Wasser- und Stromversorgung • Drehen Sie den Wasserhahn nach jedem Spülgang zu, um Schäden durch eventuelles Austreten von Wasser auszuschließen. • Ziehen Sie den Netzstecker aus der Steckdose, bevor Sie Ihren Geschirrspüler reinigen oder Wartungsmaßnahmen getroffen werden. Reinigung des Geschirrspülers • Die Gehäuseteile und die Bedienblende können mit einem mit Wasser angefeuchteten, weichen Tuch gereinigt werden. Vermeiden Sie Löse- und Scheuermittel.
Störungen und Abhilfe Sollten Betriebsstörungen auftreten, kontrollieren Sie bitte folgende Punkte, bevor Sie sich an den Kundendienst wenden. Störungen: Mögliche Ursachen/Lösung: Die Spülmaschine startet nicht oder reagiert nicht auf die Bedienungseingaben. • Wasserhahn nicht aufgedreht. • Schalten Sie das Gerät durch das Drücken der ON/OFF-Taste aus und nach etwa einer Minute wieder ein und wiederholen Sie die Programmeinstellung.
Instalación ES En caso de traslado mantener el aparato en posición vertical; si fuera necesario inclinarlo, hacerlo hacia la parte posterior. En ningún caso se debe cortar el tubo de carga de agua porque contiene partes bajo tensión. Conexiones hidráulicas La adaptación de los equipos hidráulicos para la instalación debe ser realizada sólo por personal especializado. Los tubos de carga y de descarga de agua pueden orientar hacia la derecha o hacia la izquierda para permitir una mejor instalación.
Advertencias para el primer lavado Después de la instalación, quitar los tampones colocados en los cestos y los elásticos de retención en el cesto superior (donde estén presentes. Programación ablandador de agua Antes de realizar el primer lavado, programar el nivel de durezadel agua de red. (ver capítulo Sal regeneradora y Abrillantador) La máquina dispone de señales sonoras/tonos que indican la presión del mando: encendido, fin de ciclo, etc.
Descripción del aparato ES Vista de conjunto 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Sal regeneradora y Abrillantador Utilizar sólo productos específicos para lavavajillas. No utilizar sal de cocina o industrial. Seguir las indicaciones del envase. Si se utiliza un producto multifunción, se recomienda igualmente añadir sal, especialmente cuando el agua es dura o muy dura. (Seguir las indicaciones del envase.) Si no se añade ni sal ni abrillantador, es normal que los testigos FALTA SAL y FALTA ABRILLANTADOR permanezcan encendidos.
Cargar los cestos ES Sugerencias Antes de cargar los cestos, eliminar de la vajilla los residuos de alimentos y vaciar los vasos y las copas. No es necesario aclarar la vajilla con agua corriente. Disponer la vajilla de manera que quede firme y no se vuelque. Los recipientes deben colocarse con la abertura hacia abajo y las partes cóncavas o convexas en posición oblicua, para permitir que el agua alcance todas las superficies y fluya.
Regular la altura del cesto superior Vajillas no aptas para el lavado en lavavajillas El cesto superior es de altura regulable: la posición más alta facilita la disposición de vajillas voluminosas en el cesto inferior; la posición más baja permite aprovechar los espacios de las solapas para crear más espacio hacia arriba. • Cubiertos y vajillas de madera. • Vasos decorados delicados, vajillas artesanales y antigüedades. Las decoraciones no son resistentes.
Detergente y uso del lavavajillas ES Cargar el detergente Los buenos resultados del lavado dependen de la correcta dosificación del detergente; en caso de exceso, no se lava más eficazmente y se contamina el medio ambiente. La dosis se puede adaptar al grado de suciedad. En general, para la suciedad normal hay que utilizar unos 25 g (detergente en polvo) o 25 ml (detergente líquido). Si se emplean pastillas, es suficiente una.
Programas Los datos de los programas se obtienen en condiciones de laboratorio según la Norma Europea EN 50242. La duración y los datos de los programas pueden variar según las distintas condiciones de uso. Duración del programa ES Consumo de agua (l/ciclo) Consumo de energía (kWh/ciclo) 03:00 10 0,83 Inicio diferido – Media Carga - Tab 02:30 14 1,3 Sí Inicio diferido – Media Carga - Tab 02:00 13,5 1,1 4. Frágil Sí Inicio diferido – Media Carga - Tab 01:40 10 0,95 5.
Programas especiales y opciones ES Notas: las mejores prestaciones de los programas "Smart Daily y Rápido" se obtienen preferiblemente respetando la cantidad de cubiertos especificados. Opcion Media Carga Para consumir menos use el lavavajillas a plena carga. Si la vajilla que debe lavar es poca, se puede utilizar la media carga que permite ahorrar agua, energía y detergente. Seleccionar el programa y pulsar la tecla MEDIA CARGA; el testigo se enciende.
Mantenimiento y cuidados Interrumpir el agua y la corriente eléctrica • Cerrar el grifo de agua después de cada lavado para prevenir el riesgo de pérdidas. • Desconectar la clavija de la toma de corriente para la limpieza y los trabajos de mantenimiento. Limpiar el lavavajillas • La superficie externa y el panel de control se pueden limpiar con un paño no abrasivo humedecido con agua. No utilizar disolventes ni productos abrasivos.
Anomalías y soluciones ES 195132598.01 - NC 04/2016 pb - Xerox Fabriano Si el aparato presenta anomalías de funcionamiento, controlar los siguientes puntos antes de llamar al Servicio de Asistencia Técnica. Anomalías: Posibles causas/Solución: El lavavajillas no arranca o no responde a los mandos. • El grifo de agua no está abierto. • Apagar la máquina con la tecla ON/OFF, volver a encenderla después de un minuto aproximadamente y elegir el programa.