Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADL 350/1

Before using the dishwasher, read the

installation and maintenance instructions carefully!

5019 596 01017

ADL 350

1) Programme data obtained in conformity with European standard EN 50242. The data may vary according to different loads,

different extra functions, different sensor settings (for sensor programmes only), different water supply temperatures, different

water hardnesses, different power supply voltages, etc.

2) Programme for energy data label in conformity with EN 50242. - Information for Test Laboratories:

for more detailed information

on the conditions of the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

1. OVERVIEW

On button

Off button

Delayed start button

Press the button repeatedly to delay

the start of the programme by 3, 6

or 9 hours. Then press the START

button. The dishwasher will start at

the set time.

Detergent setting upon initial use and when using a different

type of detergent

1. Select the third programme in the relative table.

2. Press the START button for approx. 7 sec. to change the

display.

3. Using the START button, select the desired detergent:

“3h” = 2in1, “6h” = 3in1, “9h” = other combined action

detergents (In this way the rinse aid and/or salt indicator is

deactivated). All 3 LEDs light up = Powder detergent

(factory setting).

4. Switch the appliance off and then switch it on again. The

selected detergent type will be indicated on the display for

approx. 3 seconds. by the corresponding LEDs.

Programme selection button

Press the button (repeatedly) until the indicator

of the required programme lights up.

START button

The indicator lights up during operation, flashes if

a fault occurs and goes off at the end of the

programme.

START button RESET function

Press this button for at least 2 seconds and the

started programme and the extra functions

selected are cancelled. The main fault indications

(repeated flashing of the START indicator) can be

cancelled with a RESET. Also see Section 5 “What

to do if...”.

An acoustic signal sounds as long as the error persists.

Table 1.1.

Programme chart

Detergent

dispenser

Consumption

Programmes

Available

options

Loading instructions

large small Litres kWh Minutes

1 Pre-Rinse cold

Crockery to be washed

later.

— — 5.0 0.02 10 ±

2 Quickwash 40°C

Lightly soiled crockery,

without dry food residuals.

X — 13.0 0.70 30 ±

Bio

50°C

Normally soiled crockery.

Energy saving programme.

X X 15.0 1.05 165 ±

4 Intensive 70°C

Recommended programme

for heavily soiled crockery,

particularly suitable for pots

and pans.

X X 17.0 1.65 145 ±

Summary of content (8 pages)

PAGE 1
Before using the dishwasher, read the installation and maintenance instructions carefully! GB ADL 350 1. OVERVIEW Programme selection button Press the button (repeatedly) until the indicator of the required programme lights up. START button The indicator lights up during operation, flashes if a fault occurs and goes off at the end of the programme. START button RESET function Press this button for at least 2 seconds and the started programme and the extra functions selected are cancelled.
PAGE 2
. QUICK REFERENCE GUIDE Detailed instructions are given in the following pages, see also chapter “5. What to do if...” 1. Switch on the appliance Open the dishwasher door. Press the ON button. 2. Select a programme Press the button or to bring up the desired programme on the display. Select options, if available. 3. Select the type of detergent The detergent selection procedure varies depending on the dishwasher model. Chapter “1. Overview” provides instructions for selecting detergent type. 4.
PAGE 3
. HOW TO USE THE APPLIANCE PROGRAMME SELECTION Press the button or to bring up the desired programme on the display. The appliance must be switched on. If required, select options (if supplied). The corresponding indicator lamp switches on. Appropriate programmes and relative available options are detailed in table 1.1 on page 1. Programme times stated in the table were obtained under normal conditions and may vary depending on conditions.
PAGE 4
3. HOW TO USE THE APPLIANCE c. How to adjust the rinse aid dosage regulator The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button 2 to open the cover. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again. If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3).
PAGE 5
3. HOW TO USE THE APPLIANCE HOW TO LOAD THE RACKS UPPER RACK - depending on the model Multifunction support A three possible positions for long utensils, cups and glasses. Crockery holder B in horizontal position: cups/long utensils, in raised position for plates and stemware. Adjustable glass holder C Depending on the position, for small or longstemmed glasses. Long-handled utensils (kitchen knives) must be arranged with the sharp end facing in towards the appliance.
PAGE 6
4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
PAGE 7
5. WHAT TO DO IF... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes/solutions ...is not working/will not start - The appliance must be switched on. Check the household circuit fuse if there is no power supply. The dishwasher door must be closed.
PAGE 8
5. WHAT TO DO IF... Crockery and cutlery ... Possible causes/solutions ...are not perfectly clean/have food residues - ...have deposits: - regeneration salt residue - In the event of frequent use of low temperature programmes (50°C or lower) (if available), every now and again select a higher temperature programme The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”).