Instruction for Use

ManualsBrandsWhirlpool ManualsOtherADP 6332 WH

GB -1-

Chart

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the

program.

When the door is opened during a washing cycle,

the cycle is temporarily paused: the Start indicator

blinks. To resume the cycle close the door and

push Start button again.

PROGRAM SELECTION

BUTTON

Push “Programs” button

(repeatedly) until the indicator

of the required program lights

up (see “Table of programs”

below).

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute.

If pressed when the dishwasher is switched off it

drains any possible liquids from dishwasher

(1 minute process).

If the indicator flashes repeatedly, see page 6 -

chapter ”What to do if ...”.

(see at right for options description)

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without

additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs

as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed

information on the EN/Standard loading comparison test and other tests, contact the following address:

“nk_customer@whirlpool.com”.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

Pre-Wash cold

Delay Crockery to be washed later. — 4.0 0.03 14 NO

Fragile 40°C

Delay

Light soiling, for example glasses

and cups.

X 10.0 0.85 100 Light

Rapid 45°C

Delay

Lightly soiled crockery, with no

dried-on food.

X 11.0 0.80 30 NO

Eco

50°C

Delay

Normally soiled crockery.

Energy-saving program.

X 12.0 1.15 150 Full

Intensive 65°C

Delay

Recommended program for heavily

soiled crockery, especially suitable for

pans and saucepans.

X 14.0 1.60 145 Full

5019 300 00226

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

SALT INDICATOR

When lit (at the end of the

cycle), the salt reservoir

needs to be refilled.

DELAYED START

BUTTON

The wash cycle can be

programmed to start

after 2, 4 or 8 hours.

Then press the Start

button. The wash

program will start after

the set time.

RINSE AID INDICATOR

When lit (at the end of the

cycle), the rinse aid

dispenser needs to be

refilled.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES

AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

TABLET SETTING

This setting allows to optimize the cycle performances

according the type of detergent used.

Push the Tablet button for 3 seconds (until the indicator

lights up) if you are using the combined detergents in

tablet (rinse aid, salt and detergent in 1 dose).

If you are using powder detergent or liquid detergent,

the Tablet indicator on the control panel has to be off.

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only before the first wash or if water hardness has been changed Water hardness level is factory set for medium-hard water (level 4). Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
PAGE 3
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B.
PAGE 4
How to load the racks UPPER RACK - depending on the model 4 A - Adjustable flaps (2 or 4): in horizontal position for cups / long utensils / stemmed glasses. A - CLOSED A - OPEN B - Cutlery basket: can be placed in the upper rack when the “Half load/Multizone” option is selected. The Grid (F) should be removed. TO OPEN A: How to adjust upper rack height (if available). It could be useful to lift up the upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open. To pause the program (e.g.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... ...is not working/will not start - Possible causes... The appliance must be switched on. Solutions... - Check the household circuit fuse if there is no power supply. - The dishwasher door doesn’t close.
PAGE 7
What to do if... Crockery and cutlery... Possible causes... Solutions... ...salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up. ...have deposits: regeneration salt residue - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly.
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.