Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADP 7609

-1-

Chart

START

DELAY

option

MULTI

ZONE

option

ON/OFF

BUTTON

PROGRAMME

SELECTOR

KNOB

(see “Table of

programmes”

below).

START BUTTON

The indicator lights up during operation, flashes when a fault occurs, and goes off

at the end of the programme.

START BUTTON RESET FUNCTION:

Press this button for at least 2 seconds; the selected programme and options will

be cancelled. Main failure displays (repeated flashing of the START indicator lamp)

can be cancelled by RESETTING. Detailed instructions are given in chapter

“What to do if...”.

(see at right for options description)

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional

options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of

the appliance’s automatic calibration system.

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed

information on the EN/Standard loading comparison test and other tests, contact the following address:

“nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut P

asteur of Lille (France), based on the NF EN 13697 standard of November 2001.

Table of programmes

Deter-

gent

Consumption

Programmes

Available

options

Loading instructions Litres kWh

Minutes

Auto Sensor 50-65°C

Delay

Multizone

Recommended programme for

routine washes, with dried-on

food (e.g. EN 50242).

— 11-16 1.10-1.50 100-130

Pre-Wash cold

Delay

Multizone

Crockery to be washed later. — 4.0 0.03 14

Quickwash 40°C

Delay

Multizone

Lightly soiled crockery, with no

dried-on food.

* Use of

tablets not recommended.

10.0 0.65 30

Eco

50°C

Delay

Multizone

Normally soiled crockery. X 12.0 1.05 160

Antibacterial

Delay

Multizone

Normally or heavily soiled

crockery, with additional

antibacterial wash. Programme

interruption (e.g. due to door

opening) can compromise

elimination of germs.

X 13.0 1.50 115

Intensive 70°C

Delay

Multizone

Recommended programme for

heavily soiled crockery, especially

suitable for pots and pans.

X 14.0 1.55 155

5019 396 01743ADP 7609

DELAYED START

BUTTON

Press the button (repeatedly)

to delay the start of the

programme. Adjustable from 1

to 24 hours. With each press of

the button, the delayed start

indicator increases by one hour

and after 24 restarts from 00.

Then press the START button.

The dishwasher will start after

the set time.

HALF LOAD/MULTIZONE

Allows you to choose the

washing zones. Press this button

to select the wash zones:

both racks

only upper rack

only lower rack

RINSE AID INDICATOR

When lit, the rinse aid dispenser needs

to be refilled.

SALT INDICATOR

When lit, the salt reservoir

needs to be refilled.

FAULT INDICATION AND WASH TIME DISPLA

In normal operation it indicates the remaining time (h:mm),

whereas with “Delayed start” selected it indicates the time

remaining until programme start (hh).

If “F..” appears on the display, see chapter “What to do if...”.

Options and display description

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE INSTALLATION

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE INSTALLATION INSTRUCTIONS! THE GUARANTEE IS NOT APPLICABLE IF FAULTS ARE CAUSED BY INCORRECT USE OF THE APPLIANCE. Options and display description PROGRAMME SELECTOR KNOB (see “Table of programmes” below). START BUTTON The indicator lights up during operation, flashes when a fault occurs, and goes off at the end of the programme.
PAGE 2
First time use How to set detergent type: powder/gel/tablet (if option is available) In order to always ensure the best cleaning results, you NEED to set: DETERGENT type and WATER HARDNESS. 1. Select 3rd programme 2. Press START button 3a. Check your (see Table of programmes for 7 seconds detergent type... - page 1) Detergent types 3b....and set it on your dishwasher using the START button (as per table below) 4. Remember to use salt and rinse aid when needed (as indicated below) 5.
PAGE 3
Daily check Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) 1 The salt level indicator lamp may remain lit for the duration of several wash cycles. If the water hardness level falls within category (soft), no salt is required. Salt indicator (depending on the model) Visual indicator (depending on model). Screw on the cap. Salt residues around cap need to be removed. Add salt (never add detergent!). min. 1.5 kg max.
PAGE 4
How to load the racks How to load UPPER RACK 4 B - Adjustable flaps: In horizontal position for cups/long utensils, in raised position for plates and stemware. (In some models only) A - Multipurpose support: Different positions for long utensils, cups and glasses. How to adjust upper rack height (if available) - It could be useful to lift up upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select programme 6 Quick, permanent or alternating Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the panel (page 1). Choose programme according to the attached table of programmes (page 1). Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open.
PAGE 6
What to do if... If a fault occurs, before restoring normal appliance operation.contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... ...is not working/will not start ...shows “F1” on the display or the START indicator lamp flashes once ...shows “F4” on the display or the START indicator lamp flashes 4 times ...
PAGE 7
What to do if... Crockery and cutlery... ...salt indicator lit ...have deposits: regeneration salt residue ...are not dry Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up. - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly. - Not enough rinse aid.
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, switch off the appliance, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).