GB User and maintenance manual
IMPORTANT SAFETY INSTRUCTIONS These instructions shall also be available on website: docs.whirlpool.eu YOUR SAFETY AND THAT OF OTHERS IS HIGHLY IMPORTANT. This manual and the appliance itself provide important safety warnings, to be read and observed at all times. This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
• When drilling through a wall or the ceiling, pay attention not to damage electric connections and/or pipes. • The ventilation ducts must always discharge to the outside. • Exhaust air must not be vented through a flue used for removal of fumes produced by appliances burning gas or other fuels, but must have a separate outlet. All national regulations governing extraction of fumes must be observed.
Declaration of conformity • This appliance has been designed, manufactured and marketed in compliance with: - safety objectives of the “Low Voltage” Directive 2014/35/EU; - the ecodesign requirements of european regulations n. 65/2014, and n. 66/2014 in conformity to the european standard EN 61591 - the protection requirements of Directive “EMC” 2014/30/EU. Electrical safety of the appliance can only be guaranteed if it is correctly connected to an approved earthing system.
TROUBLESHOOTING GUIDE The appliance does not work: • Check for the presence of mains electrical power and if the appliance is connected to the electrical supply; • Turn off the appliance and restart it to see if the fault persists. The hood's suction level is not sufficient: • Check the suction speed and adjust as necessary; • Check that the filters are clean; • Check the air vents for any obstructions.
MAINTENANCE WARNING: - Use safety gloves. - Disconnect the appliance from the mains power supply. GREASE FILTERS The metal grease filter has an unlimited life and should be cleaned once a month by hand or in a dishwasher at low temperature and with a short program. When the grease filter is washed in a dishwasher it may become opaque, but the filtering power is not altered in any way. Pull out the handle to remove the filter. Wash the filter and leave it to dry, proceeding in reverse order to refit.
MATERIAL SUPPLIED Remove all the components from the packets. Check that all the components are included. • Hood assembled with motor, lamps and grease filters installed. • Instructions for assembly and use • 1 electrical cable • 1 assembly template • 1 VNRF (2 pieces) • 2 adjustment blocks • 2 brackets for adjustment blocks • 4 screws Ø 4x8 • 4 screws Ø 3.9 x 25 • 1 support bracket • • • • • • • • 6 wall plugs Ø 8mm 6 screws Ø 5 x 45 1 cable clamp 5 screw Ø 3.5 x 9.
INSTALLATION - ASSEMBLY INSTRUCTIONS The instructions below, to be carried out in the order in which they are numbered, refer to the figures (with the same step numbers) given on the last pages of this manual. 1. Using a pencil, draw the center line on the wall up to the ceiling to facilitate installation operations. 2.
DESCRIPTION AND USE OF HOOD 1. Control panel 2. Grease filters. 3. LED lamps. 4. Telescopic flue. Control panel T1. Device ON/OFF ON: control panel on, no active function. OFF: disable all the functions in use, control panel off. Note: the hood is equipped with an “automatic shutdown” function; if the control panel is on for more than 60 seconds, and no light or motor function is selected, the hood turns off (OFF). T2. Light OFF With long press: gradual decrease of the intensity. T3.
1 2 3 4 5
6 7 8 9 10
Ø 3,5 x 9,5 11 12 13 14 15
16 17 18 19 20 21
22 23 24 25 26
27 28 29
06/2015 400010907694 GB Whirlpool® Registered trademark/TM Trademark of Whirlpool group of companies - © Copyright Whirlpool Europe s.r.l. 2015. All rights reserved - http://www.whirlpool.