GB User and maintenance manual
IMPORTANT SAFETY INSTRUCTIONS These instructions shall also be available on website: docs.whirlpool.eu. YOUR SAFETY AND THAT OF OTHERS IS HIGHLY IMPORTANT. This manual and the appliance itself provide important safety warnings, to be read and observed at all times. This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
• • • • • • • • • • • • • gas or other fuels, but must have a separate outlet. All national regulations governing extraction of fumes must be observed. If the hood is used together with other appliances operating on gas or other fuels, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar). For this reason, make sure the room is adequately ventilated. The Manufacturer declines any liability for improper use or incorrect setting of the controls.
Declaration of conformity • This appliance has been designed, manufactured and marketed in compliance with: - the ecodesign requirements of european regulations n. 66/2014, n. 327/2011, n. 244/2009, n. 245/2009, n.1194/2012, n. 2015/1428; Electrical safety of the appliance can only be guaranteed if it is correctly connected to an approved earthing system. Energy saving tips • Switch ON the hood at minimum speed when you start cooking and kept it running for few minutes after cooking is finished.
TROUBLESHOOTING GUIDE The appliance does not work: • Check for the presence of mains electrical power and if the appliance is connected to the electrical supply; • Turn off the appliance and restart it to see if the fault persists. The hood's suction level is not sufficient: • Check the suction speed and adjust as necessary; • Check that the filters are clean; • Check the air vents for any obstructions.
MAINTENANCE - use protective gloves. - disconnect the appliance from the power supply. ATTENTION: GREASE FILTERS The metal grease filter has an unlimited life and should be cleaned once a month by hand or in a dishwasher at low temperature and with a short cycle. Cleaning in a dishwasher may cause discoloring of the grease filter, but its filtering efficiency is unaffected. Open the extraction panel (twist upwards). Note: the panel does not need to be removed. Pull out the handle to remove the filter.
MATERIAL SUPPLIED Remove all the components from the packets. Check that all the components are included. • Hood assembled with motor, lamps and grease filters fitted (1 or 2 grease filters, depending on the model). • Instructions for assembly and use • 1 Assembly template • 1 - adapter Torx T10 • 1 - adapter Torx T20 • 1 deflector • 3 wall plugs Ø 8mm • 3 screws Ø 5x45 • 1 screw Ø 3.5x9.5 • 1 washer Ø 5.
INSTALLATION - ASSEMBLY INSTRUCTIONS The instructions below, to be carried out in the order in which they are numbered, refer to the figures (with the same step numbers) given on the last pages of this manual. IMPORTANT: The hood comes as a filter version. The carbon filter is supplied and must be fitted after installation. 1. Mark a vertical centre line on the wall. 2.
DESCRIPTION AND USE OF HOOD 1. Control panel. 2. Extraction panel. 3. Grease filters. 4. Halogen lamps. Control panel 1. OFF / Extraction speed (power) decrease button 2. ON / Extraction speed (power) increase button Note: The intensive extraction speed (power) is timed and lasts for 5 minutes (indicator c flashes); the hood then reverts to extraction speed (power) 2. 3. ON/OFF Timer button: delays the deactivation of the selected extraction speed (power) by 5 minutes.
1 2 3x Ø 8 x 40mm 2x Ø 5 x 45mm 5mm 3 4 5 6
8 7 9 10 11
13 14 15
03/2017 400011105400 GB Whirlpool® Registered trademark/TM Trademark of Whirlpool group of companies - © Copyright Whirlpool Europe s.r.l. 2014. All rights reserved - http://www.whirlpool.