GB User and maintenance manual
IMPORTANT SAFETY INSTRUCTIONS These instructions shall also be available on website: docs.whirlpool.eu. YOUR SAFETY AND THAT OF OTHERS IS HIGHLY IMPORTANT. This manual and the appliance itself provide important safety warnings, to be read and observed at all times. This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
• • • • • • • • • • • • • burninggas or other fuels, but must have a separate outlet. All national regulations governing extraction of fumes must be observed. If the hood is used together with other appliances operating on gas or other fuels, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar). For this reason, make sure the room is adequately ventilated. The Manufacturer declines any liability for improper use or incorrect setting of the controls.
Declaration of conformity • This appliance has been designed, manufactured and marketed in compliance with: - the ecodesign requirements of european regulations n. 66/2014, n. 327/2011, n. 244/2009, n. 245/2009, n.1194/2012, n. 2015/1428; Electrical safety of the appliance can only be guaranteed if it is correctly connected to an approved earthing system. Energy saving tips • Switch ON the hood at minimum speed when you start cooking and kept it running for few minutes after cooking is finished.
TROUBLESHOOTING GUIDE The appliance does not work: • Check for the presence of mains electrical power and if the appliance is connected to the electrical supply; • Turn off the appliance and restart it to see if the fault persists. The hood's suction level is not sufficient: • Check the suction speed and adjust as necessary; • Check that the filters are clean; • Check the air vents for any obstructions.
MAINTENANCE - use protective gloves. - disconnect the appliance from the mains power supply. CAUTION: GREASE FILTERS Metal grease filters have an unlimited life and should be washed once a month either by hand or in a dishwasher at a low temperature and with a short cycle. Washing in a dishwasher can cause grease filters to turn white, but this in no way affects efficiency. Pull out the handle to remove the filter. Wash the filter and leave it to dry, proceeding in reverse order to refit it.
MATERIAL SUPPLIED Remove all the components from the packets. Check that all the components are included. • • • • • • • • • • • • • • Hood assembled with motor, lamps and grease filters installed. Instructions for assembly and use 1 connection ring 1 electrical cable Telescopic flues 1 assembly template 6 wall plugs Ø 8mm 6 screws Ø 5x45 1 cable clamp 3 screws Ø 3.5 x 9.5 1 Flue support bracket 1 deflector Power cable 4 screws Ø 2.9x6.
INSTALLATION - ASSEMBLY INSTRUCTIONS The following instructions, given in numerical order, refer to the figures on the last pages of this manual. Note: Some instructions differ according to the hood body width and height, in which case installation differences are given in the text and in the figures. 1. 2. 3. 4. 5. Pull the panel (FRONT) firmly downwards. Push the small lever (located in the right part of the panel) to the left. Release it from the rear supports.
MAINTENANCE IMPORTANT: - Disconnect the appliance from the power supply Perimeter extraction panel cleaning Removal: Pull the panel (FRONT) firmly downwards. Cleaning: The extraction panel must be cleaned as often as the grease filter, using a rag moistened with neutral liquid detergent. Do not use products containing abrasives. DO NOT USE ALCOHOL! Fitting: The panel must be fixed at the front, in the special pins on the hood surface. IMPORTANT: Always make sure the panel is firmly fixed in place.
1 2 3 4 5
6 8 7
220-240 V ~ 50-60 Hz 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24a 24b 25a 25b
26 27 28 29 30
31 32 33
Printed in Italy 08/2017 400011170718 GB