Operation Manual

ManualsBrandsWhirlpool ManualsHobAKT 352

AKT 352 PRODUCT DESCRIPTION SHEET

5019 319 01501

To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation.

CZ SK

LIGHTING THE BURNERS

• To ignite one of the burners, turn the relative knob anticlockwise to the maximum flame setting .

• Press the knob against the control panel to ignite the burner.

• After the burner has ignited, keep the knob pressed for about 5 seconds to allow the thermocouple to warm up.

This safety device shuts off the gas if the flame goes out accidentally (draughts, interruption of gas, liquids boiling over,

etc.).

• The device must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not

remain lit, wait at least one minute before trying to light it again.

- The burner might go out when the knob is released. This means that the thermocouple has not warmed up enough.

In this case, repeat the operations described above.

PRATICAL ADVICE FOR USING THE BURNERS

For optimum burner performance, observe the following

rules:

- Use pots and pans that fit the burners (see table on the

right).

- Only use flat-bottomed pots and pans.

- Use the correct amount of water for cooking foods and

keep the pot covered.

1. Removable grid(s)

2. Semi-rapid burner

3. Rapid burner

4. Semi-rapid burner control knob

5. Rapid burner control knob

SYMBOLS

Tap closed

Max. flame

Min. flame

Burner Pot Ø

Rapid

from 24 to 26 cm

Semi-rapid

from 16 to 22 cm

DIMENSIONS AND DISTANCES TO BE MAINTAINED (mm)

NOTE: In the event a hood is fitted above the cooktop, please refer to the hood instructions for the correct

distance.

INJECTOR TABLE CATEGORY II2H3B/P

ELECTRIC SUPPLY: 230 V ~ 50 Hz

Type of gas used Type of

burner

Injector

marking

Nominal heating

capacity

Nominal

consumption

Reduced

heating capacity

Gas pressure (mbar)

min. nom. max.

NATURAL GAS

(Methane) G20

rapid

semi-rapid

128

3.00

1.65

286 l/h

157 l/h

0.60

0.35

17 20 25

LIQUEFIED

PETROLEUM GAS

(Butane) G30

(Propane) G31

rapid

semi-rapid

3.00

1.65

218 g/h

120 g/h

0.60

0.35

20 30 35

Type of gas used Model configuration Nominal heating capacity

Total nominal

consumption

Air necessary (m

) for the

combustion of 1 m

of gas

G20 20 mbar 2 burners 4.65 443 l/h 9.52

G30-G31 30 mbar 2 burners 4.65 338 g/h 30.94

Summary of content (4 pages)

PAGE 1
GB AKT 352 PRODUCT DESCRIPTION SHEET 3 1 CZ SK DIMENSIONS AND DISTANCES TO BE MAINTAINED (mm) 1. Removable grid(s) 2. Semi-rapid burner 3. Rapid burner 4. Semi-rapid burner control knob 5. Rapid burner control knob SYMBOLS Tap closed 2 Max. flame Min. flame 5 4 LIGHTING THE BURNERS • • • • - To ignite one of the burners, turn the relative knob anticlockwise to the maximum flame setting . Press the knob against the control panel to ignite the burner.
PAGE 2
PRECAUTIONS AND GENERAL RECOMMENDATIONS To get full satisfaction from your hob, please read these instructions carefully and keep them for future consultation • • • • • • • These instructions are only valid for those Countries where the destination abbreviations are mentioned on the product description sheet and on the hob. Keep the packaging material (plastic bags, polystyrene parts, etc.) out of the reach of children, as they are potentially dangerous.
PAGE 3
INSTALLATION GAS CONNECTION • • • • The gas supply system must comply with local regulations. You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no information concerning your Country is given, please ask details to your Installer.
PAGE 4
ADJUSTING MINIMUM GAS SETTING OF TAPS TROUBLESHOOTING GUIDE To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows: • tighten the screw to reduce the height of the flame (-) • loosen the screw to increase the height of the flame (+) The adjustment must be performed with the tap in minimum gas setting position (small flame) . • The primary air of the burners does not need to be adjusted.