AKZM 799 User and maintenance manual Manuel d’utilisation et d’entretien
IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT This manual and the appliance itself provide important safety warnings, to be read and observed at all times. This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others. All safety warnings are preceded by the danger symbol and the following terms: DANGER Indicates a hazardous situation which, if not avoided, will cause serious injury.
Scrapping of household appliances - This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. Before scrapping, cut off the power supply cable. For further information on the treatment, recovery and recycling of household electrical appliances, contact your competent local authority, the collection service for household waste or the store where you purchased the appliance.
Energy saving - Only pre-heat the oven if specified in the cooking table or your recipe. Use dark lacquered or enamelled baking moulds as they absorb heat far better. Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will continue to cook even once the oven is switched off. DECLARATION OF CONFORMITY - This oven, which is intended to come into contact with foodstuffs, complies with European Regulation ( ) n.
CLEANING WARNING - Never use steam cleaning equipment. Only clean the oven when it is cool to the touch. Disconnect the appliance from the power supply. Oven exterior IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with the appliance, clean immediately with a damp cloth. • Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish off with a dry cloth.
MAINTENANCE - WARNING Use protective gloves. Ensure the oven is cold before carrying out the following operations. Disconnect the appliance from the power supply. REMOVING THE DOOR To remove the door: 1. 2. 3. Open the door fully. Lift the catches and push them forwards as far as they will go (Fig. 1). Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2). To refit the door: 1. 2. 3. 4. Insert the hinges in their seats. Open the door fully.
REPLACING THE OVEN LAMP To replace the rear lamp (if present): 1. Disconnect the oven from the power supply. 2. Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover back on. 3. Reconnect the oven to the power supply. To replace the side lamp (if present): 1. Disconnect the oven from the power supply. 2. Remove the side accessory holder grilles, if present (Fig. 3). 3. Use a screwdriver to prise off the lamp cover (Fig. 7). 4.
INSTRUCTIONS FOR OVEN USE FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION 1. Control panel 2. Upper heating element/grill 3. Cooling fan (not visible) 4. Dataplate (not to be removed) 5. Light 6. Circular heating element (not visible) 7. Fan 8. Turnspit (if present) 9. Lower heating element (not visible) 10. Door 11. Position of shelves (the number of shelves is indicated on the front of the oven) 12. Rear wall N.B.
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN The wire shelf and other accessories are provided with a locking mechanism to prevent their accidental removal. Fig. 1 1. 2. Insert the wire shelf horizontally, with the raised part “A” ’upwards (Fig. 1). Angle the wire shelf when it reaches the locking position “B” (Fig. 2). Fig. 2 Fig. 3 3. Return the wire shelf to the horizontal position and push it in fully to “C” (Fig. 3). 4. To remove the wire shelf proceed in reverse order.
DESCRIPTION OF DISPLAY I H G F E A B A. B. C. D. E. F. G. H. I.
FAST PREHEATING 1. 2. 3. 4. Turn the “Functions” knob to the symbol to select the fast preheating function. Confirm by pressing : the settings are shown on the display. If the proposed temperature is that desired, press button . To change the temperature, proceed as described in previous paragraphs. The message PRE appears on the display. When the set temperature is reached, the corresponding value (e.g. 200°C) appears on the display and the acoustic signal sounds.
TIMER This function can be used only with the oven switched off and is useful, for example, for monitoring the cooking time of pasta. The maximum time which can be set is 23 hours and 59 minutes. 1. With the “Functions” knob at zero, turn the “Browse” knob to display the desired time. 2. Press button to start the countdown. When the set time has elapsed, the display will show “00:00:00” and an acoustic signal will sound. To mute the acoustic signal, press button (the time of day appears on the display).
Pizza 1. 2. 3. 4. 5. Turn the Functions knob to symbol : the display shows “BREAD”. To select the “PIZZA” function, proceed as follows: Turn the “Browse” knob: “PIZZA” appears on the display. Press to select the function. Turn the “Browse” knob to set the required temperature (between 220°C and 250°C) and confirm with button . Turn the “Browse” knob to set the required cooking duration and press to start cooking. SETTINGS Turn the “Functions” knob indicator to the symbol settings which can be changed.
KEY-LOCK This function can be used to lock the buttons and knobs on the control panel. To activate it, press and at the same time for at least 3 seconds. When activated, the functions associated with the buttons are locked and the display shows a key symbol. This function can also be activated during cooking. To deactivate it, repeat the above procedure. When the key-lock function is activated, the oven can be switched off by turning the knob to 0 (zero).
FUNCTION DESCRIPTION TABLE FUNCTION SELECTOR KNOB OFF To halt cooking and switch off the oven. LAMP To switch the oven interior light on/off. SPECIALS DEFROST To speed up defrosting of food. Place food on the middle shelf. Leave food in its packaging in order to prevent it from drying out on the outside. For keeping just-cooked food hot and crisp (e.g: meat, fried food or flans). Place food on the middle shelf. The function will not activate if the temperature in KEEP WARM the oven is above 65°.
COOKING TABLE Recipe Function Pre- Shelf (from heating bottom) Yes 2/3 Temp.
Recipe Function Pre- Shelf (from heating bottom) Yes Meat & potato pies (vegetable pie, quiche lorraine) Vols-au-vent / Puff pastry crackers Lasagna / Baked pasta / Cannelloni / Flans Lamb / Veal / Beef / Pork 1 Kg Chicken / Rabbit / Duck 1 Kg Turkey / Goose 3 Kg Baked fish / en papillote (fillet, whole) Stuffed vegetables (tomatoes, courgettes, aubergines) Toast Fish fillets / steaks Sausages / Kebabs / Spare ribs / Hamburgers 2/3 Temp.
Recipe Function Pre- Shelf (from heating bottom) Leg of lamb / Shanks - 3 Roast potatoes - 3 Vegetables au gratin - 3 Temp.
TESTED RECIPES (in compliance with IEC 50304/60350:2009-03 and DIN 3360-12:07:07) Recipe Function Pre- Shelf (from Temp. heating bottom) (°C) Time Accessories and notes (min) IEC 60350:2009-03 § 8.4.
RECOMMENDED USE AND TIPS How to read the cooking table The table indicates the best function to use for any given food, to be cooked on one or more shelves at the same time. Cooking times start from the moment food is placed in the oven, excluding pre-heating (where required). Cooking temperatures and times are purely for guidance and will depend on the amount of food and type of accessory used.
INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ VOTRE SÉCURITÉ AINSI QUE CELLE D’AUTRUI EST PARTICULIÈREMENT IMPORTANTE Le présent manuel contient d’importants messages relatifs à la sécurité, qui figurent également sur l’appareil. Nous vous invitons à les lire soigneusement et à les respecter en toute circonstance. Ceci est le symbole de danger relatif à la sécurité. Il met en garde l’utilisateur et toute autre personne contre les risques potentiels dérivant de l’utilisation de cet appareil.
- N’utilisez en aucun cas de récipients en matière synthétique pour cuire des aliments au four. Les graisses et l’huile surchauffées s’enflamment facilement. Surveillez régulièrement la cuisson si vous utilisez une quantité importante de graisse ou d’huile. Ne laissez jamais l’appareil sans surveillance pendant le processus de séchage des aliments.
CONSEILS POUR LA PROTECTION DE L’ENVIRONNEMENT Élimination des emballages Les matériaux d’emballage sont entièrement recyclables comme l’indique le symbole de recyclage ( ). Par conséquent, ne les jetez jamais dans la nature mais conformez-vous aux réglementations locales en vigueur en matière d’élimination des déchets. Mise au rebut de l’appareil - Cet appareil est certifié conforme à la Directive Européenne 2002/96/CE, concernant les Déchets d’Équipements Électriques et Électroniques (DEEE ou WEEE).
SERVICE APRÈS-VENTE Avant de faire appel au Service Après-vente : 1. Vérifiez d’abord s’il n’est pas possible de remédier par vous-même au défaut en suivant les points décrits au chapitre « Diagnostic des pannes ». 2. Éteignez puis rallumez le four pour voir si le problème a été éliminé. Si, après ces contrôles, le problème persiste, adressez-vous à votre Service Après-vente.
Accessoires : • • Faites tremper les accessoires dans du détergent à vaisselle après leur utilisation et après refroidissement. S’ils sont encore chauds, munissez-vous de gants pour les manipuler. Utilisez une brosse ou une éponge pour détacher facilement les résidus d’aliments.
ENTRETIEN AVERTISSEMENT - Munissez-vous de gants de protection. Procédez aux opérations indiquées lorsque l’appareil est froid. Veillez à toujours débrancher l’appareil. DÉMONTAGE DE LA PORTE Pour démonter la porte : 1. 2. 3. Ouvrez complètement la porte du four. Soulevez les deux manettes d’arrêt des charnières en les poussant vers l’avant, jusqu’à la butée (Fig. 1). Refermez pratiquement complètement la porte (A), soulevez-la (B) et faites-la pivoter (C) jusqu’à ce qu’elle se décroche (D) (Fig. 2).
REMPLACEMENT DE L’AMPOULE Pour remplacer l’ampoule arrière (si présente) : 1. Débranchez le four. 2. Dévissez le capot de l’ampoule (Fig. 6), remplacez l’ampoule brûlée par une ampoule neuve (voir Remarque pour connaître le type), puis revissez le capot de l’ampoule. 3. Rebranchez le four. Pour remplacer l’ampoule latérale (si présente) : 1. Débranchez le four. 2. Déposez les grilles porte-accessoires latérales, si elles sont présentes (Fig. 3). 3.
INSTRUCTIONS POUR L’UTILISATION DU FOUR POUR LE BRANCHEMENT ÉLECTRIQUE, CONSULTEZ LA PARTIE RELATIVE À L’INSTALLATION 1. Bandeau de commandes 2. Résistance supérieure/gril 3. Ventilateur (non visible) 4. Plaque signalétique (à ne pas enlever) 5. Éclairage 6. Résistance circulaire (non visible) 7. Ventilateur 8. Tournebroche (si présent) 9. Résistance inférieure (non visible) 10. Porte 11. Position des plaques (le nombre de gradins est indiqué sur la façade du four) 12.
INTRODUCTION DE GRILLES ET AUTRES ACCESSOIRES À L’INTÉRIEUR DU FOUR La grille et les autres accessoires sont équipés d’un système de blocage qui évite leur extraction involontaire. Fig. 1 1. 2. Insérez la grille horizontalement, avec la partie rehaussée « A » orientée vers le haut (Fig. 1). Inclinez la grille à la hauteur de la position de blocage « B » (Fig. 2). Fig. 2 Fig. 3 3. Remettez la grille en position horizontale et poussez-la jusqu’à ce qu’elle soit parfaitement insérée « C » (Fig. 3). 4.
DESCRIPTION DE L’AFFICHAGE I H G F E A B C D A. Visualisation des éléments chauffants actifs pour les différentes fonctions B. Symboles pour la gestion du temps : minuterie, durée de cuisson, heure de fin cuisson, heure courante C. Informations relatives aux fonctions choisies D. Fonction automatique PAIN/PIZZA sélectionnée E. Indication porte four fermée durant le cycle de nettoyage automatique (pyrolyse) F. Température intérieure du four G. Fonction Pyrolyse H. Dorage I.
PRÉCHAUFFAGE RAPIDE 1. 2. 3. 4. Sélectionnez la fonction Préchauffage rapide en tournant le bouton « Fonctions » en face du symbole . Confirmez avec la touche : les réglages s’affichent. Si la température proposée correspond à celle voulue, appuyez sur la touche . Pour la modifier, procédez comme indiqué dans les paragraphes précédents. Le message PRE s’affiche. Lorsque la température réglée est atteinte, elle est remplacée par la valeur (par exemple, 200°) accompagnée par un signal sonore.
INDICATION DE LA CHALEUR RÉSIDUELLE À L’INTÉRIEUR DU FOUR À la fin de chaque cuisson, ou à l’extinction du four, si la température à l’intérieur de l’enceinte de cuisson est supérieure à 50°C, l’affichage visualise le message HOT avec la température instantanée. Lorsque la chaleur résiduelle atteint 50°C, l’heure courante réapparaît sur l’affichage. MINUTEUR Cette fonction ne peut être utilisée que lorsque le four est éteint et est utile, par exemple, pour contrôler le temps de cuisson des pâtes.
SÉLECTION FONCTION PAIN/PIZZA En mettant l’indicateur du bouton « Fonctions » en face du symbole , on accède à un sous-menu contenant deux fonctions automatiques de cuisson pour « pain » et « pizza ». Pain 1. 2. 3. 4. Tournez le bouton « Fonctions » sur le symbole : l’affichage visualise « BREAD » (pain) avec à côté AUTO. Appuyez sur pour sélectionner la fonction. Tournez le bouton « Navigation » pour régler la température désirée (entre 180°C et 220°C) et confirmez avec la touche .
NETTOYAGE AUTOMATIQUE DU FOUR Pour la description de cette fonction, voir le chapitre NETTOYAGE et le tableau des fonctions page 34. Pour lancer le cycle de nettoyage automatique du four (pyrolyse), procédez de la façon suivante : 1. Tournez le bouton « Fonctions » sur le symbole : le message PYRO s’affiche. 2. Appuyez sur la touche pour confirmer le choix et lancer le cycle de pyrolyse.
TABLEAU DE DESCRIPTION DES FONCTIONS BOUTON DES FONCTIONS OFF LAMPE Pour interrompre la cuisson et éteindre le four. Pour allumer/éteindre l’éclairage à l’intérieur du four. FONCTIONS SPÉCIALES Pour accélérer la décongélation des aliments. Il est conseillé de placer l’aliment sur le gradin central. Laissez l’aliment dans son emballage pour DÉCONGÉLATION empêcher que sa surface ne se déshydrate. Pour conserver les aliments cuits chauds et croustillants (par exemple : viandes, fritures, flans).
PAIN/PIZZA NETTOYAGE AUTOMATIQUE PRÉCHAUFFAGE RAPIDE BOUTON DES FONCTIONS (Suite) Pour cuire différents types et formats de pain et de pizza. Cette fonction a deux programmes dont les réglages sont prédéfinis. Il suffira d’indiquer les valeurs demandées (température et durée) et le four gèrera automatiquement le cycle de cuisson optimal. Positionner la pâte sur le 2ème niveau après le préchauffage du four.
TABLEAU DE CUISSON Recette Fonction PréGradin chauffage (du bas) Oui 2/3 Temp.
Recette Fonction PréGradin chauffage (du bas) Oui Tourtes (Tourtes aux légumes, quiches) Vol-au-vent / Feuilletés Lasagnes / Pâtes au four / Cannellonis / Flans Agneau / Veau / Boeuf / Porc 1 kg Poulet / Lapin / Canard 1 kg Dinde / Oie 3 kg Poisson au four / en papillote (filet, entier) Légumes farcis (tomates, courgettes, aubergines) Pain grillé Temp.
Recette Fonction PréGradin chauffage (du bas) Pommes de terre rôties - 3 Légumes gratinés - 3 Temp.
RECETTES TESTÉES conformément aux normes IEC 50304/60350:2009-03 et DIN 3360-12:07:07 Recette Fonction PréGradin Temp. chauffage (du bas) (°C) IEC 60350:99+A1:05 +A2:08 § 8.4.
CONSEILS D’UTILISATION ET SUGGESTIONS Comment lire le tableau de cuisson Le tableau indique la meilleure fonction à utiliser pour un aliment donné, à cuire sur un ou plusieurs gradins simultanément. Les temps de cuisson commencent au moment de l’introduction du plat dans le four et ne tiennent pas compte du préchauffage (si nécessaire). Les températures et les durées de cuisson sont indicatives et dépendent de la quantité d’aliments et du type d’accessoire.
Pizza Graissez légèrement les plaques pour obtenir une pizza croustillante également sur le fond. Répartissez la mozzarella sur la pizza aux deux tiers de la cuisson. Fonction levage de la pâte Il est conseillé de toujours couvrir la pâte avec un torchon humide avant de la mettre au four. Les temps de levage dans cette fonction diminuent d’environ un tiers par rapport aux temps de levage à température ambiante (20-25°C). Le temps de levage pour 1 kg de pâte à pizza est d’une heure environ.
FR42
5019 310 01410 GB FR Whirlpool is a registered trademark of Whirlpool, USA Printed in Italy 02/2012