AKZM 834 Benutzer- und Wartungshandbuch EL Εγχειρίδιο χρήσης και συντήρησης Manuel d’utilisation et d’entretien Gebruiksaanwijzing en Onderhoudshandleiding
IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT This manual and the appliance itself provide important safety warnings, to be read and observed at all times. This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others. All safety warnings are preceded by the danger symbol and the following terms: DANGER Indicates a hazardous situation which, if not avoided, will cause serious injury.
- If the surface of the induction plate is cracked, do not use it and switch off the appliance to avoid the possibility of electric shock (only for models with induction function). - Do not touch the appliance with any wet part of the body and do not operate it when barefoot. - This appliance is designed solely for use as a domestic appliance for cooking food. No other type of use is permitted (e.g.: heating rooms).
- Do not use containers made of synthetic materials. - Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat and oil. - Never leave the appliance unattended during food drying. - If alcoholic beverages are used when cooking foods (e.g. rum, cognac, wine), remember that alcohol evaporates at high temperatures. As a result, there is a risk that vapours released by the alcohol may catch fire upon coming into contact with the electrical heating element.
ELECTRICAL CONNECTION Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front edge of the oven (visible when the door is open). • Power cable replacement (type H05 RR-F 3 x 1.5 mm2) must be carried out by a qualified electrician. Contact an authorized service centre. GENERAL RECOMMENDATIONS Before use: - Remove cardboard protection pieces, protective film and adhesive labels from accessories.
AFTER-SALES SERVICE Before calling the After-Sales Service: 1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide“. 2. Switch the appliance off and back on again it to see if the fault persists. If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.
MAINTENANCE - WARNING Use protective gloves. Ensure the oven is cold before carrying out the following operations. Disconnect the appliance from the power supply. REMOVING THE DOOR To remove the door: 1. 2. 3. Open the door fully. Lift the catches and push them forwards as far as they will go (fig. 1). Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (fig. 2). To refit the door: 1. 2. 3. 4. Fig. 1 Insert the hinges in their seats. Open the door fully.
REPLACING THE OVEN LAMP To replace the rear lamp (if present): 1. Disconnect the oven from the power supply. 2. Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover back on. 3. Reconnect the oven to the power supply. To replace the side lamp (if present): 1. Disconnect the oven from the power supply. 2. Remove the side accessory holder grilles, if present (Fig. 3). 3. Use a screwdriver to prise off the lamp cover (Fig. 7). 4.
INSTRUCTIONS FOR OVEN USE FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION 6 7 12 8 11 10 9 1. Control panel 2. Upper heating element/grill 3. Cooling fan (not visible) 4. Dataplate (not to be removed) 5. Light 6. Fan 7. Circular heating element (not visible) 8. Turnspit 9. Lower heating element (not visible) 10. Door 11. Position of shelves (the number of shelves is indicated on the front of the oven) 12. Rear wall N.B.
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN The wire shelf and other accessories are provided with a locking mechanism to prevent their unintentional removal. Fig. 1 1. 2. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1). Angle the wire shelf when it reaches the locking position “B” (Fig. 2). Fig. 2 Fig. 3 3. Return the wire shelf to the horizontal position and push it in fully to “C” (Fig. 3). 4. To remove the wire shelf proceed in reverse order.
DESCRIPTION OF DISPLAY I H G F E A B A. B. C. D. E. F. G. H. I.
FAST PREHEATING 1. 2. 3. 4. Turn the “Functions” knob to the symbol to select the fast preheating function. Confirm by pressing : the settings are shown on the display. If the proposed temperature is that desired, press button . To change the temperature, proceed as described in previous paragraphs. The message PRE appears on the display. When the set temperature is reached, the corresponding value (e.g. 200°C) appears on the display and the acoustic signal sounds.
TIMER This function can be used only with the oven switched off and is useful, for example, for monitoring the cooking time of pasta. The maximum time which can be set is 23 hours and 59 minutes. 1. With the “Functions” knob at zero, turn the “Browse” knob to display the desired time. 2. Press button to start the countdown. When the set time has elapsed, the display will show “END” and an acoustic signal will sound. To mute the acoustic signal, press button (the time of day appears on the display).
Pizza 1. 2. 3. 4. 5. Turn the Functions knob to symbol : the display shows “BREAD”. To select the “PIZZA” function, proceed as follows: Turn the “Browse” knob: “PIZZA” appears on the display. Press to select the function. Turn the “Browse” knob to set the required temperature (between 220°C and 250°C) and confirm with button . Turn the “Browse” knob to set the required cooking duration and press to start cooking. SETTINGS Turn the “Functions” knob indicator to the symbol which can be changed.
STARCLEAN™ CLEANING CYCLE To keep the oven in best condition, carry out the STARCLEAN™ cleaning cycle after each use. The cycle takes 35 minutes, including a cooling stage, and must be carried out as follows: For the description of this function, see the section CLEANING and the functions table on page 15. 1. Proceed with oven cold. 2. Wet the cellulose cloth provided under running water and wring it out so that it does not drip. 3. Open the oven door and remove the enamelled accessories. 4.
FUNCTION DESCRIPTION TABLE FUNCTIONS KNOB OFF LAMP DEFROST To stop cooking and switch off the oven. To switch the oven interior light on/off. To speed up defrosting of food. Place food on the middle shelf. Leave food in its packaging in order to prevent it from drying out on the outside. SPECIALS For keeping just-cooked food hot and crisp (e.g: meat, fried food or flans). Place food on the middle shelf. The function will not activate if the KEEP WARM temperature in the oven is above 65°C.
BREAD/PIZZA STARCLEAN™ FAST PREHEATING FUNCTIONS KNOB (Continued) To bake different types and sizes of pizza and bread. This function contains two programmes with predefined settings. Simply indicate the values required (temperature and time) and the oven will manage the cooking cycle automatically. Place the dough on the 2nd shelf after preheating the oven. To eliminate the dirt created by cooking by means of a low temperature cycle.
COOKING TABLE Recipe Function Pre- Shelf (from heating bottom) Temp.
Recipe Function Pre- Shelf (from heating bottom) Temp.
Recipe Roast chicken 1-1.3 Kg Function Pre- Shelf (from heating bottom) - Temp.
Table of Tested Recipes (in compliance with IEC 60350-1:2011-12 and DIN 3360-12:07:07) Recipe Function Pre- Shelf (from Temp. heating bottom) (°C) Time Accessories and notes (min) IEC 60350-1:2011-12 § 7.5.
RECOMMENDED USE AND TIPS How to read the cooking table The table indicates the best function to use for any given food, to be cooked on one or more shelves at the same time. Cooking times start from the moment food is placed in the oven, excluding preheating (where required). Cooking temperatures and times are purely for guidance and will depend on the amount of food and type of accessory used.
5019 300 02328 DE GR FR NL Whirlpool is a registered trademark of Whirlpool, USA Printed in Italy 07/2012
