Instruction for Use

5019 300 00039
PREPARATION OF THE WASH CYCLE
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a
wash programme is running, the lid remains locked and
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to “Cancel (Reset) a running programme before
the end”.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) . Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the Prewash option.
“Rapid” button
• Enables quicker washing by shortening the
programme duration.
• Recommendable for small loads or only lightly soiled
laundry.
“Intensive rinse” button
• The amount of water is increased to ensure a more
intensive rinse.
• This option is particularly suitable for areas with very
soft water, washing baby linen and people with skin
allergies.
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• This option is particularly recommended for
the “Synthetics”, “Daily load” and “Delicates”
programmes.
• It is useful if you want to postpone spinning to a later
time, or if you want to drain out only.
• If you select “Rinse hold”, do not leave items to soak
for too long.
• As soon as the appliance stops in the rinse hold, the
“Rinse hold” lamp of the sequence indicator lights up and
the lamp next to the “Start(Pause)” button flashes.
Whirlpool is a registered trademark of Whirlpool USA.
PROGRAMME START
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been executed yet.
“Cold wash” button
• Water is heated only up to 20°C.
• Suitable for delicate laundry items with wash
temperature recommendation of max. 30°C on the
care label.
• Selectable only on the lowest temperature step
of each programme.
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the
values in the table in relation to the water supply pressure and temperature, the load and the type of wash. Water and energy consumption refer to the default setting of
the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that
time (see also “Troubleshooting Guide” in your Instructions for Use).
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Standard Cotton programme and basis for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
FAILURE INDICATIONS
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
without
“Rapid”
(kWh)
Approx. Programme Duration
(hours : minutes)
without “Rapid” with “Rapid”
Cotton/Antibacterial 95 6.0 55* 1.90 2:00 1:50
Cotton 60 6.0 48 1.14 2:30 1:45
Cotton 40 6.0 48 0.64 2:15 1:30
Jeans 40 4.0 41 0.58 1:44 -
Synthetics 60 3.0 50* 0.90 2:05 1:14
Synthetics 40 3.0 40 0.50 1:50 0:59
Delicate 40 1.5 50 0.55 0:45 -
Delicate 30 1.5 50 0.50 0:41 -
Daily load 40 3.0 40 0.45 1:00 -
Speed 15’ 30 3.0 30 0.15 0:15 -
Wool/Handwash 40 1.0 40 0.55 0:35 -
Wool/Handwash Cold 1.0 40 0:10 0:30 -
Eco Cotton** 60 6.0 48 0.90 3:30 -
Eco Cotton** 60 3.0 35 0.78 2:30 -
Eco Cotton 40 6.0 48 0.70 2:30 -
Eco Cotton** 40 3.0 35 0.57 2:05 -
CONSUMPTION DATA
Power consumption in off-mode 0.11 W / in left-on mode 0.11 W
1. Load the machine, close the drum doors and check
that they are properly locked.
2. Add detergent as indicated an the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The lamp next to
the “Start(Pause)” button flashes. The indication
lamp of the predefined spin speed lights up. If you
do not start the programe soon after having made
your choice, the washing machine will switch off
automatically after about a quarter of an hour.
Switch on the washing machine again by turning the
programe selector back to „Off/O“ and then to the
desired programe.
Open the tap and press the “Start(Pause)” button.
The indication lamp next to the “Start(Pause)” button
lights up. The programme sequence indicator shows the
current programme phase, running from left to right
through Wash, Rinse, Spin/Drain. When the programme
phase is finised, the corresponding indication goes out.
• Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”
No or not sufficient inlet water.
“Service”
Failure or malfunction of an electrical component.
“Clean pump”
Waste water is not pumped out.
Spin speed on programme sequence indicator
blinks: unbalance during spinning
CANCEL A RUNNING PROGRAMME BEFORE
THE END
The “Reset” button cancels a programme before the
end. Press the “Reset” button for at least 3 seconds.
Any existing water is drained out before the door can be
opened.
PROGRAMME END
• All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
After about a quarter of an hour, the washing
machine will switch off completely to save energy.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the interior
of the machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start(Pause)” button to pause the
programme. The light blinks.
2. Select the new programme, temperature, any
options and another spin speed if you want.
3. Press the “Start(Pause)” button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
Terminate the “Rinse hold” option:
• Press the “Start(Pause)” button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain” programme
and press the “Start(Pause)” button.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only.