Operation Manual

ManualsBrandsWhirlpool ManualsAir ConditioningAMD 012

BEFORE USING THE APPLIANCE

To make the most out of your new appliance,

please read the user instructions carefully and keep

them handy for future consultation.

Before using the appliance please follow and

set according to the below indications:

Remote Control (RC) presetting:

Each time the batteries are replaced in the remote

control, the RC is pre-set on Heat pump.

If the air conditioner that you purchased is a

cooling only, then the pre-set on Heat pump will

not bring any changes.

Auto-Restart presetting Function:

To set the auto-restart function, press the

Emergency button (ON/OFF) on the indoor unit

for at least 5 seconds

A buzz sound will signal that the auto-restart

function is set and the air conditioner is in standby.

To cancel the auto-restart function, repeat the

above steps.

SAFETY PRECAUTIONS

• Do not install the appliance if it is connected to

the power supply.

• The Installation and service/repair must be

performed by a qualified technician, in

compliance with the producer's instructions and

following local safety norms. Do not repair or

replace any parts of the appliance unless it is

specifically written in the user instructions.

• The grounding of this appliance is compulsory.

• Make sure that the power supply cord is long

enough to allow the right connection. Do not

use any extension cord for power supply.

• Do not pull the power supply cord to remove it

from the socket.

• Do not twist or press the power supply cord,

and make sure it is not broken.

• Once installation is completed, the electric

components must not be accessible to the users.

• Do not touch the operation buttons when your

hands are wet and don't use the appliance when

you are barefoot.

• Physically or mentally disabled people, children

and people without any experience with the

product are only allowed to use the appliance if

they have had specific training on how to

operate the appliance by a person responsible

for their security and well-being. The appliance

is not intended for use by disabled people and

very young children without supervision.

Summary of content (22 pages)

PAGE 1
BEFORE USING THE APPLIANCE To make the most out of your new appliance, please read the user instructions carefully and keep them handy for future consultation. Auto-Restart presetting Function: To set the auto-restart function, press the Emergency button (ON/OFF) on the indoor unit for at least 5 seconds A buzz sound will signal that the auto-restart function is set and the air conditioner is in standby. To cancel the auto-restart function, repeat the above steps.
PAGE 2
AIR CONDITIONER PRECAUTIONS Please strictly follow the below instructions: • Long and direct exposure to cool air might be harmful to health. It is advisable to set the louvers in order to avoid direct cool air and deflect it within the room. • Prevent the air flow from reaching the gas burners and stoves. • Upon malfunctioning first turn the appliance off by pressing the ON/OFF button on the remote control, then disconnect it from the mains. • Do not place any objects on the outdoor unit.
PAGE 3
PRODUCT DESCRIPTION Indoor unit 1. Air Intake 2. Front Panel 3. Display panel 4. Electrical box 5. Air Outlet 6. Filter monitor reset button 7. Vertical Adjustment Louver 8. Horizontal Adjustment Louver 9. Air Filter 10. Remote Control Outdoor unit 11. Air Intake 12. Pipes and Power Connection Cord 13. Drain Hose Note: Condensate water drains at COOLING or DRY operation. 14.
PAGE 4
CONTROL PANEL DISPLAY INDICATORS DESCRIPTION Temperature indicator (1) Displays set temperature. Running indicator (2) It lights up during operation. It flashes during outside unit defrosting. Timer indicator (3) It lights up during the set time. It goes off when timer operation ends. Sleep indicator (4) It lights up during sleep mode. Filter monitor indicator (5) Filter monitor indicator flashes after 240 hours of usage as reminder to clean the filter.
PAGE 5
REMOTE CONTROL FUNCTIONS AND INDICATORS 1. ON/OFF BUTTON Starts and/or Stops the appliance by pressing this button. 2. TIMER BUTTON Sets or cancels the timer operation. 3-4. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. Used to set time in timer mode. 5. MODE BUTTON Used to select the operation mode. 6. BUTTON Used to set or cancel 6th sense operation, also during stand-by. 7. SLEEP BUTTON Used to set or cancel Sleep Mode operation. 8.
PAGE 6
STORAGE AND TIPS FOR USING THE RC How to insert the batteries Remove the battery cover in the direction of the arrow. Insert new batteries making sure that the (+) and (-) of battery are matched correctly. Refit the cover by sliding it back into position. Note: • Use 2 LR03 AAA (1.5volt) batteries. Do not use rechargeable batteries. Replace batteries with new ones of the same type when the display becomes dim. • If the replacement is done within 1 minute, the remote control will keep original presetting.
PAGE 7
OPERATING MODE DESCRIPTION Operation Modes: 1. Selecting mode Each time MODE button is pressed, the operation mode is changed in sequence: COOLING → DRY → FAN ONLY → HEATING ↑ Heating mode is not available for cooling only air conditioners. 2. FAN mode Each time the "FAN" button is pressed, the fan speed is changed in sequence: Auto → High → Medium → Low ↑ At "FAN ONLY" mode, only "High","Medium" and "Low" are available.
PAGE 8
AIRFLOW DIRECTION CONTROL 5. Airflow direction control Vertical airflow is automatically adjusted to a certain angle in accordance with the operation mode after turning on the unit. The direction of airflow can be also adjusted to your own requirement by pressing the "SWING" button of the remote control. Operation mode Direction of airflow COOLING, DRY horizontal *HEATING, FAN ONLY downward *Heating mode is only available for heat pump models.
PAGE 9
MODE AND FUNCTION DESCRIPTIONS 6th SENSE MODE Press the button, the unit enters 6th sense mode directly regardless of the unit is on or off. In this mode, temperature and fan speed are automatically set based on the actual room temperature. Operation mode and temperature are determined by indoor temperature. Heat pump models Indoor Operation temperature mode 21°C or below HEATING 21°C-23°C FAN ONLY 23°C-26°C DRY Over 26°C COOLING Target temperature 22°C Room temperature decrease 1.
PAGE 10
SLEEP mode SLEEP mode can be set in COOLING or HEATING operation mode. This function gives you a more comfortable environment for sleep. In SLEEP mode, • The appliance will stop operation automatically after operating for 8 hours. • Fan speed is automatically set at low speed. • Set temperature will rise by max 1°C if the appliance operates in cooling mode for 2 hours. • Set temperature will decrease by 3°C at most if the appliance operates in heating mode for 3 hours.
PAGE 11
Timer function It is convenient to set the timer on by pressing the button to achieve a comfortable room temperature at the time you get home. You can also set timer off automatically to enjoy a good sleep at night. Timer-setting Set the timer when the appliance is off. Switch-off timer during operation. A - As time goes by, LCD on remote control only displays the remaining time not the set temperature. B - The previous set time is stored and the next set time begins with the previous setting.
PAGE 12
MAINTENANCE Unit 1. Unplug from the power supply Turn off the appliance first before disconnecting from power supply. 2. To remove the front panel pull it outwards (Fig. A). 3. Wipe with a soft and dry cloth. Use lukewarm water (below 40°C) to clean if the appliance is very dirty. 4. Never use substances such as gasoline or polishing powder to clean the appliance. 5. Never sprinkle water onto the indoor unit Dangerous! Electric shock! 6. Refit and close the front panel (Fig. B).
PAGE 13
• Install the outdoor unit at a place where the air discharged and the operation noise would not annoy your neighbours. • Do not place any obstacles in front of the air outlet of the outdoor unit lest it increases the noise level. Features of HEATING mode Preheating 2-5 minutes are necessary to preheat the indoor unit at HEATING operation start. Defrosting (out door unit) In HEATING operation the appliance will defrost (de-ice) automatically to raise efficiency. This procedure usually lasts 2-10 minutes.
PAGE 14
INSTALLATION INSTRUCTIONS Installation diagram Distance from ceiling should be over 50mm Distance from wall should be over 50mm Distance from the wall should be over 50mm Distance from floor should be over 2000mm Air intake distance from the wall should be over 250mm Air intake distance from the wall should be over 250mm Ai shor out uld let be dist ov anc er e f 50 rom 0m m the wa ll Over 250mm NOTE: The figure above is only a simple presentation of the unit, it may not match the external appearance
PAGE 15
Select the best location Location for Installing Indoor Unit • Where there is no obstacle near the air outlet and air can be easily blown to every corner. • Where piping and wall hole can be easily arranged. • Observe the required distance from ceiling and wall according to the wiring diagram. • Where the air filter can easily be removed. • Keep the unit and remote control 1m or more from television, radio etc. • To prevent the effects of a fluorescent lamp, keep the unit as far as possible from it.
PAGE 16
INDOOR UNIT INSTALLATION 1. Installing the Mounting Plate • Select a location to install the mounting plate according to the indoor unit location and piping direction. • Adjust the mounting plate horizontally with a horizontal ruler or plumb line. • Drill holes 32mm in deep on the wall to fix the plate. • Insert the plastic plugs in the hole, then fix the mounting plate with tapping screws. • Check that the mounting plate is well fixed. Then drill a hole for piping.
PAGE 17
IMPORTANT: Piping Joints Thermal Insulation: Wrap the piping joints with thermal insulating materials and then wrap with a vinyl tape. Wrapped with vinyl type Thermal insulation Thermal Insulation piping: a. Place the drain hose under the piping. b. Insulation material: polythene foam over 6mm in thickness. Thermally insulated tube Large pipe Power cord NOTE: Drain hose is prepared by user. • Drain pipe should point downward for easy drain flow.
PAGE 18
Piping Connection: a. Connect indoor unit pipes with two wrenches. Pay special attention to the torque allowed as shown below to prevent the pipes, connectors and flare nuts from being deformed and damaged. b. At first fingers-tighten them, then use the wrenches. Model Pipe size Torque Nut width Min. thickness 7,9,12,18K Liquid Side (1/4 inch) 1.8kg.m 17mm 0.6mm 24K Liquid Side (3/8 inch) 3.5kg.m 22mm 0.6mm 7,9k Gas Side (3/8 inch) 3.5kg.m 22mm 0.6mm 12k Gas Side (1/2 inch) 5.5kg.
PAGE 19
CAUTION: 1. Use an individual power circuit specifically for the air conditioner. As for the wiring method, refer to the circuit diagram on the inside of the access door . 2. Check that the cable thickness conforms to the power source specification. 3. Check the wires and make sure that they are all tightly fastened after cable connection. 4. Be sure to install an earth leakage circuit breaker in a wet or moist area.
PAGE 20
• Power supply from Indoor unit, including 18K Model HEAT PUMP Indoor unit Outdoor unit Terminal Terminal Brown Brown Blue Blue power connecting cord 1 Brown Brown Blue Blue power connecting cord Yellow/Green Yellow/Green • Power supply from outdoor unit, including 24K Model For these models, the power supply is connected from outdoor unit, with a circuit breaker.
PAGE 21
OUTDOOR UNIT INSTALLATION 1. Install Drain Port and Drain Hose (for heatpump model only) The condensate drains from the outdoor unit when the unit operates in heating mode. In order not to disturb your neighbours and protect the environment, install a drain port and a drain hose to direct the condensate water. Just install the drain port and rubber washer on the chassis of the outdoor unit, then connect a drain hose to the port Washer as shown in the figure on the right . Drain port 2.
PAGE 22
How to Purge Air Tubes: (1). Unscrew and remove caps from 2 and 3-way valves. (2). Unscrew and remove cap from service valve. (3). Connect vacuum pump flexible hose to the service valve. (4). Start vacuum pump for 10-15 minutes until it reaches an absolute vacuum of 10 mm Hg. (5). With vacuum pump still running close the low pressure knob on vacuum pump manifold. Then stop vacuum pump. (6). Open 2-way valve 1/4 turn, then close it after 10 seconds.