Instrucciones para el uso LAVADORA Sumario ES Espanol,1 GB English, 13 DE Deutsch, 25 ES Instalación, 2-3 Desembalaje y nivelación, 2 Conexiones hidráulicas y eléctricas, 2-3 Primer ciclo de lavado, 3 Datos técnicos, 3 Descripción de la lavadora, 4-5 Panel de control, 4 Luces testigo, 5 Puesta en marcha y Programas, 6 En la práctica: poner en marcha un programa, 6 Tabla de programas, 6 Personalizaciones, 7 AVXL 109 Seleccione la temperatura, 7 Seleccionar el centrifugado, 7 Funciones, 7 Detergen
Instalación ES Es importante conservar este manual para poder consultarlo en cualquier momento. En caso de venta, de cesión o de traslado, verifique que permanezca junto con la lavadora para informar al nuevo propietario sobre el funcionamiento y brindar las correspondientes advertencias. Una cuidadosa nivelación brinda estabilidad a la máquina y evita vibraciones, ruidos y desplazamientos durante el funcionamiento.
Conexión del tubo de descarga Una vez instalada la lavadora, la toma de corriente debe ser fácilmente accesible. No utilice alargadores ni conexiones múltiples. El cable no debe estar plegado ni sufrir compresiones. Primer ciclo de lavado Después de la instalación y antes del uso, realice un ciclo de lavado con detergente y sin ropa, seleccionando el programa a 90ºC sin prelavado. Datos técnicos Dim ensio nes an ch o 59 ,5 cm. altu ra 8 5 cm. profu n didad 5 6,5 cm. Capacidad de 1 a 6 kg .
Descripción de la lavadora Panel de control Botones de FUNCIÓN ES Luces testigo Botón de ENCENDIDO/APAGADO Luz indicadora de ENCENDIDO/PUERTA BLOQUEADA Leyenda Mando de Cajón de detergentes Botón de PROGRAMAS START/RESET Mando de Mando de CENTRIFUGADO TEMPERATURA Cajón de detergentes: para cargar detergentes y aditivos (véase la pág. 8). Mando de TEMPERATURA: para seleccionar la temperatura o el lavado en frío (ver la pág. 7).
Luces testigo Prelavado Lavado Descripción Retraso seleccionado: Si fue activada la función Delay Timer (ver la pág. 7), después de haber puesto en marcha el programa, comenzará a centellear la luz testigo correspondiente al retraso fijado: Fase en curso: Durante el ciclo de lavado, las luces testigo se encenderán progresivamente para indicar su estado de avance.
Puesta en marcha y Programas ES En la práctica: poner en marcha un programa 4. 5. 6. 7. Fije la temperatura de lavado (ver la pág. 7). Fije la velocidad de centrifugado (ver la pág. 7). Vierta el detergente y los aditivos (véase la pág. 8). Ponga en marcha el programa pulsando el botón START/RESET. Para anular, mantenga presionado el botón START/RESET durante 2 segundos como mínimo. 8.
Personalizaciones Seleccione la temperatura Girando el mando de la TEMPERATURA se selecciona la temperatura de lavado (ver la Tabla de programas en la pág. 6). La temperatura se puede disminuir hasta el lavado en frío ( ). Instalación Seleccionar el centrifugado . Se puede disminuir la velocidad de centrifugado o excluirlo seleccionando el símbolo La máquina impedirá automáticamente efectuar un centrifugado a una velocidad mayor que la máxima prevista para cada programa.
Detergentes y ropa ES Cajón de detergentes Prendas especiales El buen resultado del lavado depende también de la correcta dosificación del detergente: si se excede la cantidad, no se lava de manera más eficaz, sino que se contribuye a encostrar las partes internas de la lavadora y a contaminar el ambiente. Cortinas: pliéguelas y colóquelas dentro de una funda o de una bolsa de red. Lávelas solas sin superar la media carga. Utilice el programa 11 que excluye automáticamente el centrifugado.
Precauciones y consejos La lavadora fue proyectada y fabricada en confor- Seguridad general Este aparato fue fabricado para uso doméstico. No toque la máquina con los pies desnudos ni con las manos o los pies mojados o húmedos. No abra el contenedor de detergentes mientras la máquina está en funcionamiento. En ningún caso fuerce la puerta: podría dañarse el mecanismo de seguridad que la protege de aperturas accidentales.
Mantenimiento y cuidados ES Excluir agua y corriente eléctrica Limpiar la bomba Cierre el grifo de agua después de cada lavado. De este modo se limita el desgaste de la instalación hidráulica de la lavadora y se elimina el peligro de pérdidas. La lavadora posee una bomba autolimpiante que no necesita mantenimiento. Pero puede suceder que objetos pequeños (monedas, botones) caigan en la precámara que protege la bomba, situada en la parte inferior de la misma.
Anomalías y soluciones Puede suceder que la lavadora no funcione. Antes de llamar a la Asistencia Técnica (ver la pág. 12), controle que no se trate de un problema de fácil solución ayudándose con la siguiente lista. ES La lavadora no se enciende. El enchufe no está introducido en la toma de corriente, o no hace contacto. En la casa no hay corriente. El ciclo de lavado no comienza. La puerta no está bien cerrada. no fue pulsado. El botón El botón START/RESET no fue pulsado.
Asistencia Antes de llamar a la Asistencia Técnica: Verifique si la anomalía la puede resolver solo (ver la pág. 11); Vuelva a poner en marcha el programa para controlar si el inconveniente fue resuelto; Si no es así, llame a la Asistencia técnica autorizada, al número de teléfono indicado en el certificado de garantía. No recurra nunca a técnicos no autorizados. ES Comunicar: el tipo de anomalía; el modelo de la máquina (Mod.); el número de serie (S/N ).
Instructions for use WASHING MACHINE Contents GB English GB Installation, 14-15 Unpacking and levelling, 14 Electric and water connections, 14-15 The first wash cycle, 15 Technical details, 15 Washing machine description, 16-17 Control panel, 16 Leds, 17 Starting and Programmes, 18 Briefly: how to start a programme, 18 Programme table, 18 Personalisations, 19 AVXL 109 Setting the temperature, 19 Setting the spin cycle, 19 Functions, 19 Detergents and laundry, 20 Detergent dispenser, 20 Preparing yo
Installation GB Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features. Read these instructions carefully: they contain vital information on installation, use and safety.
Connecting the drain hose When the washing machine is installed, the mains socket must be within easy reach. Do not use extensions or multiple sockets. The power supply cable must never be bent or dangerously compressed. the socket is compatible with the washing machine's plug. If this is not the case, replace the socket or the plug. Dim ensio ns 5 9 .
Washing machine description GB FUNCTION Control panel Buttons Leds START/STOP Button ON-OFF/DOOR LOCK l Programme key Led PROGRAMME Detergent dispenser Knob START/RESET Button SPIN SPEED TEMPERATURE Knob Knob Detergent dispenser: to add detergent and fabric softener (see page 20). TEMPERATURE knob: to set the temperature or the cold wash cycle (see page 19). Programme key to consult a straightforward chart of the different programmes available: pull the grey tab outwards to open it.
Leds Prewash Wash Rinse Spin cycle Note: during draining, the LED corresponding to the Spin cycle phase will be turned on. Once the set delay is complete, the flashing LED will turn off and the programme set will start. Detergents Function buttons The FUNCTION BUTTONS also act like LEDS. When a function is selected, the corresponding button is illuminated. If the function selected is incompatible with the programme set, the button will flash and the function will not be enabled.
Starting and Programmes GB Briefly: starting a programme 5. Set the spin speed (see page 19). 6. Add the detergent and any fabric softener (see page 20). 7. Start he programme by pressing the START/RESET button. To cancel it, keep the START/RESET button pressed for at least 2 seconds. 8. When the programme is finished, the ON-OFF/ DOOR LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly.
Personalisations Setting the temperature GB Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 18). The temperature can be lowered, or even set to a cold wash ( ). Installation Setting the spin speed Description Turn the SPIN SPEED knob to set the spin speed for the programme selected. The maximum spin speeds for each programme are as follows: Programmes Maximum spin speed Cottone 1000 rpm Synthetics 800 rpm Wool 600 rpm Silk no Programmes .
Detergents and laundry GB Detergent dispenser Special items Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. Curtains: fold curtains and place them in a pillow case or mesh bag. Wash them separately without exceeding half the appliance load. Use programme 11 which excludes the spin cycle automatically.
Precautions and advice The washing machine was designed and built in Disposing of an old washing machine: before scrapping your appliance, cut the power supply cable and remove the appliance door. This washing machine should only be used by adults and in accordance with the instructions provided in this manual. Saving energy and respecting the environment Never touch the washing machine when barefoot or with wet or damp hands or feet.
Care and maintenance GB Cutting off the water or electricity supply Turn off the water tap after every wash. This will limit the wear of your appliance's water system and also prevent leaks. Unplug your appliance when cleaning it and during all maintenance operations. Cleaning your appliance The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Troubleshooting Your washing machine could fail to work. Before calling for Assistance (see page 24), make sure the problem can't easily be solved by consulting the following list. The appliance is not plugged into the socket, or not enough to make contact. There has been a power failure. The wash cycle won't start. The appliance door is not shut properly. The button has not been pressed. The START/RESET button has not been pressed. The water tap is not turned on.
Service Before calling for Assistance: Check whether you can solve the problem on your own (see page 23); Restart the programme to check whether the problem has been solved; If this is not the case, contact an authorised Technical Service Centre on the telephone number provided on the guarantee certificate. GB If the machine has been installed or used incorrectly, you may be charged for the maintenance callout service Always request the assistance of authorised servicemen.
Bedienungsanleitungen WASCHVOLLAUTOMAT INHALTSVERZEICHNIS DE Deutsch DE Installation, 26-27 Auspacken und Aufstellen, 26 Wasser- und Elektroanschlüsse, 26-27 Erster Waschgang, 27 Technische Daten, 27 Beschreibung des Waschvollautomaten, 28-29 Schalterblende, 28 Kontrollleuchten, 29 Inbetriebnahme und Programme, 30 Kurz zusammengefasst: Waschprogramm starten, 30 Programmtabelle, 30 Individualisierungen, 31 AVXL 109 Einstellen der Temperatur, 31 Einstellen der Schleuder, 31 Funktionen, 31 Waschmitte
Installation DE Es ist äußerst wichtig, diese Bedienungsanleitung sorgfältig aufzubewahren, um sie jederzeit zu Rate ziehen zu können. Sorgen Sie dafür, dass sie im Falle eines Umzugs oder Übergabe an einen anderen Benutzer das Gerät stets begleitet, damit auch der neue Inhaber die Möglichkeit hat, diese zu Rate zu ziehen. Lesen Sie bitte folgende Hinweise aufmerksam durch, sie liefern wichtige Informationen hinsichtlich der Installation, dem Gebrauch und der Sicherheit.
Anschluss des Ablaufschlauches DE Verwenden Sie bitte keine Verlängerungen oder Mehrfachstecker. Installation 65 - 100 cm Schließen Sie den Ablaufschlauch, ohne ihn dabei zu krümmen, an eine Ablaufleitung, oder an einen in der Wand in einer Mindesthöhe von 65 - 100 cm angelegten Ablauf an; Das Kabel darf nicht gebogen bzw. eingeklemmt werden.
Beschreibung des Waschvollautomaten DE Schalterblende Taste FUNKTIONEN Kontrollleuchten Taste EIN/AUS Kontrollleuchte ON/FÜLLFENSTER GESPERRT Anzeigetafel Wahlschalter Waschmittelschublade PROGRAMME Taste START/RESET Wahlschalter Wahlschalter TEMPERATUR SCHLEUDER Waschmittelschublade: für Waschmittel und Zusätze (siehe Seite 32). Anzeigetafel: die zu jeder Zeit einen klaren Überblick über die möglichen Programme gewährleistet. Ganz einfach an der grauen Zunge herausziehen.
Kontrollleuchten Vorwäsche Startvorwahl erfolgt: Wurde die Startvorwahl-Funktion Delay Timer (siehe Seite 31) aktiviert, und das Programm in Gang gesetzt, schaltet die Kontrollleuchte, die der eingestellten Zeitverschiebeung entspricht, auf Blinklicht: Hauptwäsche Spülen Anmerkung: Während des Abpumpens leuchtet die entsprechende Kontrollleuchte für die Schleuder auf. Waschmittel Vorsichtsmaßregeln Nach Ablauf der vorgewählten Zeit erlischt die Kontrollleuchte und das gewählte Waschprogramm startet.
Inbetriebnahme und Programme DE Kurz zusammengefasst: Waschprogramm starten 5. Einstellen der Schleudergeschwindigkeit (siehe Seite 31). 6. Waschmittel und Zusätze einfüllen (siehe Seite 32). 7. Programm durch Druck auf die Taste START/RESET in Gang setzen. Um dieses zu löschen, Taste START/RESET für mindestens 2 Sekunden gedrückt halten. 8. Ist das Waschprogramm abgelaufen schaltet die Kontrollleuchte ON/FÜLLFENSTER GESPERRT auf Blinklicht, was anzeigt, dass das Fenster geöffnet werden kann.
Individualisierungen Einstellen der Temperatur Durch Drehen des Wahlschalters TEMPERATUR wird die Waschtemperatur eingestellt. (siehe Programmtabelle auf Seite 30). Die Temperatur kann bis auf Kaltwäsche ( ) herabgesetzt werden. Anmerkung: Sollte die Taste jedoch auf Blinklicht schalten, bedeutet dies, dass die Funktion zu dem eingestellten Programm nicht zugeschaltet werden kann. Delay Timer (Startvorwahl) Anleitungen zur Anwendung Aktiv mit den Programmen: Start kann bis zu 9 Std. verschoben werden.
Waschmittel und Wäsche DE Waschmittelschublade Besondere Wäscheteile Ein gutes Waschergebnis hängt auch von einer korrekten Waschmitteldosierung ab: Eine zu hohe Dosierung bedeutet nicht unbedingt reinere Wäsche, sie trägt nur dazu bei, die Maschineninnenteile zu verkrusten und die Umwelt zu belasten. Gardinen: Gardinen zusammengefaltet in einem Kissenbezug oder in einem netzartigen Beutel waschen. Waschen Sie diese allein, ohne das Gesamtgewicht für halbe Füllung zu übersteigen.
Vorsichtsmaßregeln und Hinweise Allgemeine Sicherheit Ziehen Sie den Gerätestecker nicht am Kabel aus der Steckdose, sondern nur am Stecker selbst. Öffnen Sie die Waschmittelschublade nicht, wenn das Gerät in Betrieb ist. Berühren Sie nicht das Ablaufwasser, es kann sehr heiß sein. Bei etwaigen Störungen versuchen Sie bitte nicht, Innenteile selbst zu reparieren. Während des Waschgangs kann das Füllfenster sehr heiß werden.
Reinigung und Pflege DE Wasser- und Stromversorgung abstellen Wasserhahn nach jedem Waschvorgang zudrehen. Hierdurch wird der Verschleiß der Wasseranlage verringert und Wasserlecks vorgebeugt. Ziehen Sie den Stecker aus der Steckdose, bevor Sie Ihren Waschvollautomaten reinigen. Reinigung der Pumpe Ihr Gerät ist mit einer selbstreinigenden Pumpe ausgerüstet, eine Wartung ist demnach nicht erforderlich.
Störungen und Abhilfe Es kann immer einmal vorkommen, dass Ihr Waschvollautomat nicht funktioniert. Bevor Sie sich an den Technischen Kundendienst wenden (siehe Seite 36), vergewissern Sie sich zuerst, ob es sich nicht um eine Kleinigkeit handelt, die Sie selbst beheben können. Ziehen Sie hierzu nachstehendes Verzeichnis zu Rate. Mögliche Ursachen / Lösungen: Der Waschvollautomat schaltet sich nicht ein. Der Stecker steckt nicht in der Steckdose, oder nicht so, dass der Kontakt hergestellt wird.
Kundendienst 195038552.02 07/2005 - Xerox Business Services Bevor Sie sich an den Kundendienst wenden: Kontrollieren Sie zuerst, ob das Problem nicht allein gelöst werden kann (siehe Seite 35); Starten Sie das Programm erneut, um sicherzustellen, dass die Störung auch wirklich behoben wurde; Ist dies nicht der Fall, dann kontaktieren Sie den autorisierten Kundendienst unter der auf dem Garantieschein aufgedruckten Telefonnummer.