Instruction for Use

GB 14
a.“Water tap closed” indication lights up
The appliance has no or insufficient water supply.
For models with remaining time display, “FH”
appears on that display. The “Start/Pause”
indicator flashes.
Check whether:
• the water tap is fully turned on, and the water
supply pressure is sufficient.
• the water inlet hose is kinked.
• the mesh filter in the water inlet hose is blocked
(see “Care and Maintenance”).
• the water in the water inlet hose is frozen.
• the washing machine has a safety hose and the
safety valve is open (red indicator in the safety
valve inspection window). In this case replace it
with a new safety hose.
Reconnect the washing machine.
Press the “Start/Pause” button to continue with
the programme (do not add any more detergent for
this programme).
If the fault re-occurs, contact After-Sales Service
(see “After-Sales Service”).
b.“Clean pump” indication lights up
Waste water is not pumped out. For models with a
remaining time display, “FP” appears on that
display. The washing machine stops in the
respective programme step. Unplug the appliance.
Check whether:
• the drain hose is kinked (see “Installation”).
• the pump impeller is obstructed (see “Cleaning
the Filter”).
• the water in the drain hose is frozen.
If water has remained in the drum, you can drain it
by following the instructions in the chapter
“Draining Residual Water”.
IMPORTANT: Before draining, allow the wash
water to cool down.
Reconnect the washing machine to the mains.
Select and start the “Drain” programme or push
the “Reset” button for at least 3 seconds and
restart the desired programme.
If the fault occurs again, contact After-Sales Service
(see “After-Sales Service”).
c.“Service” indication lights up
The appliance stops during the programme.
For models with a remaining time display, a failure
code between “F02” and “F35”, “FA”, “Fod” or
“bdd” appears on that display.
If all the lights of the programme sequence
indicator light up (and, for models with
display, “bdd” appears on the display):
The drum doors have not been closed properly.
Push the “Reset” button for at least 3 seconds and
wait until the “Door open” indication lights up.
Open the lid and close the drum doors, then select
and start the desired programme again. If the fault
persists, notify our After-Sales Service.
If a failure code between “F02” and “F35”
appears on the display (if available on your model):
Select and start the “Drain” programme or push the
“Reset” button for at least 3 seconds.
Then select and start the desired programme again.
If the fault persists, unplug the appliance and contact
After-Sales Service (see “After-Sales Service”).
If failure code “FA” appears on the display
(if available on your model):
Switch the appliance off, pull out the mains plug and
turn the water tap off. Tilt the appliance forward
carefully to allow the collected water to flow out
from the bottom of the appliance.
Then:
1.connect the appliance to the electrical supply;
2.turn the water tap on (if water immediately flows
into the appliance again, without the appliance
being started, there is a failure. Turn off the tap
and notify After-Sales Service);
3.select and start the desired programme again.
If the failure occurs again, unplug the appliance and
contact our After Sales Service (see “After-Sales
Service”).
If failure code “Fod” appears on the display
(if available on your model):
Too much foam interrupted the washing
programme. Avoid excessive detergent dosing.
1.Select and start the “Rinse & Spin” programme.
2.Afterwards, select and start the desired
programme again, using less detergent.
3.If the fault persists, unplug the appliance and
contact our After-Sales Service.
If your washing machine has no remaining
time display, check which of the above
described situations could be the origin of the
fault and follow the according instructions.
IFU-TL-Domino_GB.fm Page 14 Tuesday, December 19, 2006 3:06 PM
Black process 45.0° 100.0 LPI