Instruction for Use

Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
without “Rapid”
Approx. programme duration
(hours : minutes)
without “Rapid” with “Rapid”
Mixed 40 4.0 48 0.50 1:00 -
Cotton 95 7.0 74** 2.20 2:30 -
Cotton 60 7.0 54 1.19 2:20 1:35
Cotton 40 7.0 66 0.75 2:05 1:15
Synthetics 60 3.0 46** 0.90 1:35 1:10
Synthetics 40 3.0 42 0.50 1:20 0:55
Delicates 40 1.5 60 0.65 0:50 -
Delicates 30 1.5 60 0.40 0:46 -
Wool/Handwash 40 1.0 45 0.55 0:40 -
White 40 7.0 68 0.80 2:20 -
Light colours 40 4.0 60 0.45 1:20 -
Dark 40 4.0 40 0.55 1:40 1:15
Eco Cotton * 60 7.0 54 0.84 4:00 -
Eco Cotton * 60 3.5 40 0.63 3:00 *** -
Eco Cotton * 40 3.5 40 0.61 3:00 *** -
AquaEco 40 3.0 19 0.45 1:00 -
Speed 15´ 30 3.0 25 0.15 0:15
-
Jeans 40 4.0 52 0.50 1:30 1:10
Whirlpool is a registered trademark of Whirlpool USA.
5019 300 00002
Load the laundry, close the door and turn the programme
selector to the desired programme; the “Start/Pause” indicator
blinks.
The temperature and spin speed shown on the display can
be altered by pressing the “Temperature” button or the “Spin”
button . If you do not use the “Dosing Aid”, add detergent now.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
When the combination of programme and additional option(s)
is not possible, the indication switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Colours 15°” button
• Saves energy used for water heating while maintaining a good
wash result.
• Supports colour maintenance when washing coloured
laundry.
• Recommendable for lightly soiled laundry without stains.
• Make sure that your detergent is suitable for cold wash
temperatures (15 or 20°C).
• Not selectable for Cotton 70 - 95°C.
“Rapid” button
• Enables quicker washing by shortening the programme
duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 70 - 95°C.
“Prewash” button
• Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
• Recommended for heavily soiled laundry (e.g. with sand
or granular dirt).
• Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
“Soil level” button
• Adapts the programme duration to the soil level of your
laundry. Also influences the detergent quantity
recommendation when using the “Dosing Aid” button.
= lightly soiled - = normally soiled - = heavily soiled
Not all soil levels are selectable for each programme.
“Spin” button (incl. “Rinse hold”)
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If you select spin speed “0”, the final spinning is cancelled
and the water is drained out only. However, intermediate
spin phases remain during the rinse.
• If you select “Rinse hold”, the laundry remains in the last rinse
water without progressing to the final spin cycle, to avoid
creasing and prevent colours from changing. To activate the
“Rinse hold”, press the “Spin” button repeatedly until the
“Rinse hold” symbol on the display lights up.
- The wash programme stops to “Rinse hold” when the
“Rinse hold” symbol on the display blinks; the light of “Start/
Pause” button also blinks.
- To terminate the „Rinse hold“ by spinning the laundry, press
“Start/Pause” - the laundry will be spun with the default spin
speed. You can also select another spin speed with the „Spin“
button before you start the spin cycle by pressing “Start/
Pause”.
- To terminate the „Rinse hold“ by draining the water without
spinning, press the „Spin“ button until spin speed „0“ appears
on the display; then press “Start/Pause” to start the
draining.
- Do not leave the laundry to soak for too long in the “Rinse
hold” (especially silk).
- the sensor technology adapts water, energy and programme duration to the size of your wash load.
Before starting and after end of a programme, the lamp lights to
show the the door can be opened. As long as a wash programme
is running, the door remains locked and must on no account be
forced open. In case you have an urgent need to open it during
a running programme, refer to “Reset” a running programme
before the end”.
Open the tap and press the “Start/Pause” button .
The indicator next to the “Start/Pause” button lights up.
FAILURE INDICATION
The “Door open” indicator lights up, and the display shows “End”.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the “Start/Pause” button again. The new programme
continues at the same position where the previous
programme was interrupted. Do not add detergent for this
programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset/Drain” button cancels a programme before the end.
• Press and hold the “Reset/Drain” button for a few seconds;
an animation appears on the display. The water is drained out;
it may last some time until you can open the door.
With this function you can postpone your programme to
complete at a later time: press the button to select in how many
hours the programme shall be finished. Thus, it allows you to
have your laundry ready at a particular time and to profit from
more favorable energy rates during the night, for example.
• The time until the “Cycle end” can be selected in full hour time
segments (1 to 24 h). When you press the button, the shortest
possible time will be displayed; keep on pressing the button to
loop through all the available times. To remove it again, keep
on pressing the button until you see the value “0:00”.
• When you have selected the desired time until the “Cycle
end”, press “Start/Pause” - the countdown will begin.
• During the countdown, you can still modify the programme
setting (select or deselect options, change spin speed etc.).
If the modifications prolong the programme duration so that
it overruns the originally set time until the “Cycle end”, the
programme will start immediately.
• Sometimes the programme may finish before the selected
time until the “Cycle end” has expired (e.g. for small loads).
In this case, the washing machine will tumble the laundry
regularly to keep it fresh, until the selected “Cycle end” time
has expired. During tumbling, the display will show an
animation. The tumbling phase can be stopped at any time
either by pressing any button or by rotating the programme
selector; the animation will stop and the door will unlock in
about 1 minute as indicated on the display.
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water
”Service”: failure or malfunction of an electrical
component
”Clean pump”: waste water is not pumped out.
Spin speed on display blinks: unbalance during spinning.
DETERGENT OVERDOSAGE INDICATION
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time. If the symbol
lights up and the display shows “Fod”, too much foam
interrupted the wash process; refer to the “Troubleshooting
Guide” in your Instructions for Use.
With the “Dosing Aid” button, you can make your washing
machine indicate you the recommended detergent quantity for
your wash load, depending on the soil level selected and the size
of the load.
• Helps to save detergent and protect the environment and
also sensitive skin by avoiding detergent overdosing.
• Before you use this function, you must adapt the washing
machine to the dosing amounts which are recommended
for the detergents you use. Also check if your region’s water
hardness corresponds with the water hardness level “soft” of
your washing machine - if not adapt it.
• Select programme, options and cycle end BEFORE using the
“Dosing Aid” button.
For any details, refer to the separate “Dosing Aid” Instructions
for Use.
CHILD LOCK
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/O” position. To activate the child lock:
• Turn the programme selector to a programme position,
or run a programme as usual.
• Press the 2 buttons marked with the key symbol simultaneously
for at least 3 seconds. A key-like symbol will shortly appear
on the display to indicate that the child lock is active.
Any time you try to change a programme setting with active child
lock, the display will briefly show the key-like symbol.
The programme setting cannot be changed anymore.
The only change possible is to switch the washer off by turning
the programme selector to the “Off/O” position.
To deactivate the child lock:
• Press again the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds.
The „Eco monitor“ gives you a rough feedback about the power
consumption of the programme setting you selected. As soon as
you turn the programme selector to any programme, the „Eco
monitor“ is on.
less more
The indicator on the left is to show that the „Eco monitor“ is
active. The four indicators next to it show the degree of
consumption: the less power your programme setting is forecasted
to consume, the less indicators will light up. This depends on the
programme, temperature and options selected, and also on the
size of the wash load. For that reason, the forecasted degree
of power consumption may adapt when the washing machine
detects the wash load.
PROGRAMME END
ECO MONITOR
SET CYCLE END
DETERGENT DOSING RECOMMENDATION
PROGRAMME START
“DOOR OPEN” INDICATION
CONSUMPTION DATA
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water supply
pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through the cold fill
valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the energy consumption by
reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default setting of the programmes, with
temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also “Troubleshooting
Guide” in your Instructions for Use).
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
Power consumption in off-mode 0.11 W / in left-on mode 2.32 W